Please select Into the mobile phone version | Continue to access the computer ver.
Lightbridge 2 - No function at RTH Button
2217 10 2016-11-7
Uploading and Loding Picture ...(0/1)
o(^-^)o
fansc0f6a5f7
New

Germany
Offline

Hello everybody,
i have a problem with my lightbridge 2, because the home button did not work. My configuration is lightbridge 2 with A2 controller. I have connect the s-bus wire and CAN bus wire. I see all channels from the lightbride 2 transmitter in the A2 assistant software CH 1-5 and CH 7-14 but only channel 6 is death. If i press the home button the light ring around is not lighting. Transmitter is set to master, video signal is okay, i can start stop the motors and flying GPS/ATTI/Manual is possible.
Can someone solve my problem ?
Thank you, Arne
2016-11-7
Use props
DJI-Jamie
DJI team
Flight distance : 112405 ft
United States
Offline

Can you please clarify what firmware you are running on Lightbridge 2?
2016-11-7
Use props
fansc0f6a5f7
New

Germany
Offline

Hi Jamie, yust try to find out and at DJI Go APP show Aircraft Status - LatestFirmware. I am using the Android Go APP. Or is there any other way to find out the Firmware Version ? Best Regards Arne  
2016-11-8
Use props
fans1651e2ee
lvl.3
Flight distance : 176335 ft
United States
Offline

Iam having same issues with LB 2 and A3 no gear switch and no Return Home function plus the AL and EV sticks does not work right all latest firwmware. With switch in P mode AL works correct -10000 ot 10000
but elavotor is -10000 to left and -1000 to right put switch in A & S and the elevator and alieron only shows -10000 to left and -10000 to right. Yaw and throttle seem to work correctly in Assistant 2 but not the El AL and no gear swtich function or Return Home function. So far SUPER DISSPOINTED with this setup been messing with it siince Saturday to get nowhere. And Yes its all new.
2016-11-8
Use props
fansc0f6a5f7
New

Germany
Offline

hi fans1651e2ee. May be you need to calibrate the sticks. Try DJI Go App, call transmitter settings and open the calibration page. Start calibration and move the sticks to all end points.(turn around to all corners). Save calibration when sicks are in middle position. Hope it helps.  
2016-11-8
Use props
lechrob
New

Germany
Offline

Hi
did you solve your problems with the not working RTH Botton so far?
2017-1-13
Use props
fans6f57d5c6
lvl.3
Flight distance : 171496 ft
United States
Offline

Exact same problem.  

S1000
A2
Z15-BMPCC
Lightbridge 2

All the latest firmware.  Checked and rechecks wiring.  This is an upgrade from Lightbridge 1, which worked fine.

Sure could use some help

Thanks
2017-2-27
Use props
fansa605563a
lvl.3
Flight distance : 11778 ft
United States
Offline

I'm having the same issue. I can map the ch but it does not do anything when I push the button. I also tried holding it down no luck. All firmware are updated. Did someone find a solution?

DJI S900
LB 2
A2
Z15-GH4
2017-3-25
Use props
NFA Fabrication
lvl.1
United States
Offline

EXACT same problem as OP here. I was hoping someone had posted a solution when I found this thread. Bummer.
2018-1-23
Use props
wpdadmin
lvl.1

United States
Offline

I am having the same problem.  Was a solution found for this?
2018-10-17
Use props
JoiCam
Second Officer
Flight distance : 771434 ft
Iceland
Offline

Same problem here. LB2 and A2.
2018-12-22
Use props
Advanced
You need to log in before you can reply Login | Register now

Credit Rules