Did my first flight today with my MAir 2S and during the flight a warning popped up that said ' Motor Error - Check propellors and fly with caution'.  I landed immediately and double-checked that the props were installed correctly and they were.
This is the exact error warning: Motor error. Check propellers and fly with caution (Code: 30163)

This warning popped up about 4 times during my flight - should I be concerned ??

Seems strange, I would be concerned. Did you buy care refresh?

JimDandy Posted at 5-6 01:34
Seems strange, I would be concerned. Did you buy care refresh?

Sure did, i only got the drone this week and as stated, it was my first flight.

Hello there Mavic2018. I am sorry fro the trouble this has caused and thank you for reaching out. Can you please try to check if your propellers are placed properly and try a test flight to see if the error message will sill show? If the error message shows on your future flights it would be best to contact our DJI Support team at https://www.dji.com/support for further assistance. Thank you and fly safe always.

DJI Stephen Posted at 5-6 02:39
Hello there Mavic2018. I am sorry fro the trouble this has caused and thank you for reaching out. Can you please try to check if your propellers are placed properly and try a test flight to see if the error message will sill show? If the error message shows on your future flights it would be best to contact our DJI Support team at https://www.dji.com/support for further assistance. Thank you and fly safe always.

Blades were definitely installed correctly, having been a Mavic 2 Zoom flyer for the past 3 years and never seen that warning before. I landed, double-checked the blades, even removing each one and reinstalling.  Did another flight and the pop warning message appeared again.

The error message as shown in Airdata

I recall a few similar issues from earlier threads, so maybe check the following...
- Any strange motor noises when idle on the ground?
- Do the motors feel smooth when turning?

Obviously fly with caution and keep an ear & eye out on anything strange on the first few flights.

RobZilla Posted at 5-6 05:06
I recall a few similar issues from earlier threads, so maybe check the following...
- Any strange motor noises when idle on the ground?
- Do the motors feel smooth when turning?

Thanks RobZilla,

Having only had the drone for 2 days and subsequently only done 1 or 2 short flights, I really havent noticed anything unusual.  It is a bit un-nerving to see that pop up warning though.

Maybe the log would tell which motor/ prop may be giving the errors. I think this might end up being be a DJI return, sorry!  

Update -09May21 -  swapped out all propellors and installed a new set - no motor errors since.

Mavic2018 Posted at 5-9 05:01
Update -09May21 -  swapped out all propellors and installed a new set - no motor errors since.

Have you tried putting the other propellers back again. It would be interesting to know if you get the error back again. If you get the error back, can you see any warping or other things on the props compared to the one that works. Just interested to know how sensitive this issue is.

i got the same error on Mini 2 after i changed damaged propellers, but it happens only in sport mode with full trottle... got that error 5 times in first flight with new props, and day after it just stop... today, after fly app update i flew and it happened again, but just once... i never got that error in cine or normal mode... is it just app bug or what?

djiuser_us5XHwwv1pnL Posted at 2021-10-24 04:04
i got the same error on Mini 2 after i changed damaged propellers, but it happens only in sport mode with full trottle... got that error 5 times in first flight with new props, and day after it just stop... today, after fly app update i flew and it happened again, but just once... i never got that error in cine or normal mode... is it just app bug or what?

Did you only get an error or did you also hear the drone make a strange sound? I have the same issues, new set of propellers on the way currently for my Dji Mini 2. Check out this video, this is what it sounds like for me (this is my video): https://youtu.be/9HwH5yxeWMk

Same problem as described here. Error motor code 30163 and 22s after that message RTH activated but drone losse control and error in IMU code 30002 activated several times, finally crashed due this error.
Note that was a replacement unit received 3 days ago with only 5 flights and new propellers correctly installed...no strange sounds and movements in that flights...

Maybe a motor fabrication issue?

I had this issue pop up on a fresh out of the box Air 2s tonight.  I replaced the props, issue gone.  Put the first ones back on, error is back.  At least my issue was related so some apparently bad props.  

Hello there
I got the same warning several times on my mini 2 se when I was flying a few days ago. After an inspection, I saw the grey metallic mount for the props on the motor is a bit loose.
Does anyone know what's exactly wrong and what I have to do?
Greetings

djiuser_XsYSTghSwNZ4 Posted at 7-18 02:40
Hello there
I got the same warning several times on my mini 2 se when I was flying a few days ago. After an inspection, I saw the grey metallic mount for the props on the motor is a bit loose.
Does anyone know what's exactly wrong and what I have to do?

Hi there,
thank you for reaching out.

We apologize for any inconvenience caused. Please ensure that the propellers are free from cracks, bends, or damage, and that the firmware is updated to the latest version. Additionally, could you verify that the propellers are correctly installed and conduct a test flight to determine if the problem continues?

Should the issue persist, kindly let us know. Thank you.

DJI Diana Posted at 7-18 03:15
Hi there,
thank you for reaching out.

Hello
I did several tests flights and first everything was looking normal but suddenly when it was near me, it fell out of the sky and directly recontrolled itself. Now I belief it's because of the motor that's a bit loose and needs to be replaced. In that case, does the warranty cover it? The drone isn't further damaged or unscrewed and is bought in June 2023.
Greetings

djiuser_XsYSTghSwNZ4 Posted at 8-27 10:18
Hello
I did several tests flights and first everything was looking normal but suddenly when it was near me, it fell out of the sky and directly recontrolled itself. Now I belief it's because of the motor that's a bit loose and needs to be replaced. In that case, does the warranty cover it? The drone isn't further damaged or unscrewed and is bought in June 2023.
Greetings

Hi there,
thank you for reaching out.

We regret to hear about the incident. We recommend you send the aircraft for further diagnosis and inspection since the drone has crashed since it may cause damage to both physical structure and electronic components. Kindly proceed to contact our support at https://www.dji.com/be/support to start a case.

Should you have any other questions, kindly message us here for assistance. Thank you.