Hello all,
I'm seeking a solution for this problem, as it's getting really frustrating, and I can't understand If I'm the one doing something wrong.

I'm not able to use my Avata - it is not pairing. I have tried everything. Firmware is updated on all the devices. The main issue is the fact that when I'm trying to manually bind the devices, my Avata is not entering in the pairing mode. Pressing the battery button for at least 4-5 seconds, doesn't work. somewhere at the second 3 is getting out of the blinking sequence.

I really hope some of you got a solution for this situation and looking forward for one.

remove the battery from the avata and press the battery button till it starts .. then deep press the battery without connecting it for 3 seconds .. does it blinks ?


if it blinks .. insert the battery to the avata while its being ON and then try to pair

Hi there. Thank you for reaching out and we do apologize for the trouble. After pressing the link button on the Goggles. The Goggles will start to beep as it indicates that it entered linking mode, you need to "PRESS AND HOLD" the power button on the aircraft until the battery level LEDs start to blink in sequence. If the issue persists, please record a short video showing the problem and send it to us so we can check it further. Please keep us posted.

MAF178 Posted at 3-16 14:25
remove the battery from the avata and press the battery button till it starts .. then deep press the battery without connecting it for 3 seconds .. does it blinks ?

Unfortunately, it doesn't enter in the pairing mode/blinking sequence.

While I'm pressing and holding the button, it's blinking like it is counting seconds - always at the 3rd blink, is stopping.

DJI Paladin Posted at 3-16 21:56
Hi there. Thank you for reaching out and we do apologize for the trouble. After pressing the link button on the Goggles. The Goggles will start to beep as it indicates that it entered linking mode, you need to "PRESS AND HOLD" the power button on the aircraft until the battery level LEDs start to blink in sequence. If the issue persists, please record a short video showing the problem and send it to us so we can check it further. Please keep us posted.

Experiencing the exact same issue and have spent hours trying to troubleshoot it to no success. Pressing the battery power button for 3-4 seconds does nothing but make the  LEDS blink 3 times and stops. The frontal LED is blinking rainbow. Would the environment affect the pairing ability? E.G indoors comapred to outdoors? Got this thing a few days ago and still trying to get it to pair.

IceBlueMink Posted at 3-27 21:31
Experiencing the exact same issue and have spent hours trying to troubleshoot it to no success. Pressing the battery power button for 3-4 seconds does nothing but make the  LEDS blink 3 times and stops. The frontal LED is blinking rainbow. Would the environment affect the pairing ability? E.G indoors comapred to outdoors? Got this thing a few days ago and still trying to get it to pair. [view_image]

Hi there. Thank you for reaching out and we do apologize for the trouble. Can you please confirm if you have managed to activate the unit before? If you are having issues with pairing the aircraft, goggles, and remote controller, kindly download first the DJI Assistant 2 software on your computer and update all the components (one by one) to its latest firmware then try linking them again to see if the issue persists. You may download the software using the link below. Please follow the tutorial below for the guide on how to set up the unit. Please keep us posted.

DJI Assistant 2 software: https://www.dji.com/global/downl ... sumer-drones-series

I'm having the same issue, only mine was flying fine for over a year until I updated to firmware 1.05. I had the drone in the air moments before deciding to land and update the firmware, after which point it allowed me to fly for all of two seconds before popping up with an error and starting RTH. I canceled RTH and flew it back (about 10ft), landed, and it immediately disconnected and began flashing rainbow. I've updated firmware, made sure batteries were fully charged, updated my headset and controller, and even tried the weird powered battery plug-in hack mentioned above. Nothing seems to work.

I'm just lucky I wasn't flying for a gig at the time, because this issue would have cost me a job.

DJI Paladin Posted at 3-30 03:08
Hi there. Thank you for reaching out and we do apologize for the trouble. Can you please confirm if you have managed to activate the unit before? If you are having issues with pairing the aircraft, goggles, and remote controller, kindly download first the DJI Assistant 2 software on your computer and update all the components (one by one) to its latest firmware then try linking them again to see if the issue persists. You may download the software using the link below. Please follow the tutorial below for the guide on how to set up the unit. Please keep us posted.

DJI Assistant 2 software: https://www.dji.com/global/downloads/softwares/dji-assistant-2-consumer-drones-series

I've followed each and every step, being sure I have all the devices updated, without succeeding...

this is disappointing....

d.buzdugan Posted at 4-25 12:16
I've followed each and every step, being sure I have all the devices updated, without succeeding...

this is disappointing....

Thank you for your response and we do apologize for the trouble. Kindly upload a short video showing the issue so we can check the behavior further. Also, please include the firmware version you are using with your aircraft, goggles, and remote controller for further investigation. Please keep us posted.

Same/similar issue, details below.

Setup:
* Avata (1 battery reports v01.05.0000, for the other battery see below)
* Goggles 2 (v01.09.0000)
* 2x RC Motion 2 controllers (v02.00.0700)
* 1x FPV RC 2 controller (v02.00.0900)
* 2x Intelligent Flight Battery
* DJI Assistant 2 (Consumer Drone Series) (v2.121, macOS Sonoma)

Problem & Troubleshooting:
Upon launching the DJI app on my iPhone and starting the "Connection Guide", I can't get past step 3 of 4 (shown at top of DJI App) which prompts to pair a remote.

Following the instructions, I power on the remote. The lights blink and then turn solid green. After a few seconds of not automatically pairing, the text at the bottom changes to "Trouble linking your remote?" (or some such) that, when tapped, gives instructions to hold down the power button on the remote for 4 seconds and then tap the "Pair" button on the screen. Tapping the "Pair" button starts a 60 second countdown and disables the button.

The remote seems to pair (lights stop cycling in sequence, all lights are on and solid) but the "Pair" 60 second timer in the DJI app continues to countdown until it reaches 0 and issues an error that the attempt failed.

Tapping the "3/4" (step 3 of 4) at the top of the DJI app results in the attached screenshot. i

I can bypass by tapping "Camera View" at the top of the DJI app on my phone on this screen. Using the Goggles 2, I can then see what the drone sees. "Status" menu reports no issues, the "RC" signal meter at the bottom is white (not greyed out, like it would be if it can't find any remote) and signal bars are full.

No compass, calibration, or any other error or failure shown on any menu. Pressing the "Mode" button on any remote results in the UI within the Goggles 2 UI to reflect the switch from "Normal" to "Sport".

However, the rotors don't start upon pressing the "Lock" button twice in quick succession.

I have access to an additional RC Motion 2 controller and FPV RC 2 controller and the issue/behavior persists across all 3 remotes.

The only other thing "of note" is that when connecting the Avata to my computer and opening DJI Assistant 2, one of the two batteries causes the "Firmware Update" tab to just display "Loading" indefinitely. It doesn't present the current firmware version installed like it does when the other battery, remotes, or goggles are connected.

Have attempted outdoors and indoors. Drone was flying fine with either battery a week ago.

DJI Paladin Posted at 4-26 20:08
Thank you for your response and we do apologize for the trouble. Kindly upload a short video showing the issue so we can check the behavior further. Also, please include the firmware version you are using with your aircraft, goggles, and remote controller for further investigation. Please keep us posted.

https://youtu.be/kP3sg6JwGTg

Above the video.

As I have mentioned all the devices are updated to the last firmware.

Looking forward for your reply.

d.buzdugan Posted at 4-28 07:19
https://youtu.be/kP3sg6JwGTg

Above the video.

Thank you for the information provided. We will coordinate this with our relevant team for further investigation. We will keep you posted.

DJI Paladin Posted at 4-28 19:41
Thank you for the information provided. We will coordinate this with our relevant team for further investigation. We will keep you posted.

Any updates on this, please?

d.buzdugan Posted at 5-2 12:38
Any updates on this, please?

Hi there. Sorry for the late response. If your aircraft firmware is already the latest version, please confirm whether there is an SD card installed in the aircraft. If yes, please remove the SD card and try to enter the binding state again then check if the issue persists. Please keep us posted.

DJI Paladin Posted at 5-3 00:36
Hi there. Sorry for the late response. If your aircraft firmware is already the latest version, please confirm whether there is an SD card installed in the aircraft. If yes, please remove the SD card and try to enter the binding state again then check if the issue persists. Please keep us posted.

I have tried:

1. with the removed card
2. by inserting the card back
3. by removing the card again.

All 3 are individual binding instances.

I would really appreciate a quicker response..... It's been over a year since I bought it, and I haven't had a chance to fly it yet due to these stubborn pairing problems. It's incredibly frustrating, especially when I see newer models hitting the market.

Just a heads up, I still have an active DJI Care Refresh 2-Year Plan for my DJI Avata. So, I'm really hoping we can get this sorted out soon and make the most out of my investment.

d.buzdugan Posted at 5-4 08:34
I have tried:

1. with the removed card

Thank you for keeping us posted.  In this case, I'm afraid that you may consider sending the unit in for a proper diagnosis. You may contact our support team to start up a ticket at https://www.dji.com/support or create an online ticket using this link https://repair.dji.com/repair/index . Also, the warranty can be applied depending on the outcome of the damage assessment including the warranty period of your unit. We appreciate your understanding.

DJI Paladin Posted at 5-4 21:30
Thank you for keeping us posted.  In this case, I'm afraid that you may consider sending the unit in for a proper diagnosis. You may contact our support team to start up a ticket at https://www.dji.com/support or create an online ticket using this link https://repair.dji.com/repair/index . Also, the warranty can be applied depending on the outcome of the damage assessment including the warranty period of your unit. We appreciate your understanding.

Hello. Was there ever an update or fix on this? I am having the exact same problem, where the Avata will not enter pairing mode. It does not beep, only flashes light buttons a few times and does nothing.

I downloaded assistant 2 and updated firmware, removed the sd card and tried again, etc. But have had no success at all.

Please assist.

undavidable Posted at 5-18 15:54
Hello. Was there ever an update or fix on this? I am having the exact same problem, where the Avata will not enter pairing mode. It does not beep, only flashes light buttons a few times and does nothing.

I downloaded assistant 2 and updated firmware, removed the sd card and tried again, etc. But have had no success at all.

Hi there. We're deeply sorry for the trouble. If you already perform the troubleshooting steps above and still the issue persists, I'm afraid that we cannot fix it remotely, kindly contact our team using the link above to send back the unit for proper diagnostics. Thank you for your understanding.

me too but my indicator  light is yellow  now blinking

fans20f68474 Posted at 6-11 00:52
me too but my indicator  light is yellow  now blinking

Hi there,
thank you for reaching out.

If the indicator blinks yellow quickly, that means your DJI Avata is not connected to the remote controller.

Kindly inform us the full details of the issue that you experienced with your DJI product and we will surely provide you with an accurate resolution after we review the details.

In addition, please post a short sample video showing the said issue for us to see and assist you further. Thank you!

I was having the same issue but I have sorted it now. Turns out the battery wasn't connected to the aircraft properly. After insterting the battery press the connector into place to make sure it is properly located. HTH

darren7urner Posted at 7-26 13:00
I was having the same issue but I have sorted it now. Turns out the battery wasn't connected to the aircraft properly. After insterting the battery press the connector into place to make sure it is properly located. HTH

Hi there,
thank you for reaching out.

We appreciate the update provided. If the issue persists, please inform us.

Should you have any other questions, kindly message us for assistance. Thank you.

If your drone's led doesn't lit at all; then, look at the battery receptacle of your Avata and notice a broken pin cut and not reaching the top for the battery plug to make contact.

DJI Natalia Posted at 6-11 01:06
Hi there,
thank you for reaching out.

Cannot enter pairing mode

DJI Paladin Posted at 3-16 21:56
Hi there. Thank you for reaching out and we do apologize for the trouble. After pressing the link button on the Goggles. The Goggles will start to beep as it indicates that it entered linking mode, you need to "PRESS AND HOLD" the power button on the aircraft until the battery level LEDs start to blink in sequence. If the issue persists, please record a short video showing the problem and send it to us so we can check it further. Please keep us posted.

Where I can share a video
I wanna send video for my pairing mode problem

d.buzdugan Posted at 3-16 23:08
Unfortunately, it doesn't enter in the pairing mode/blinking sequence.

While I'm pressing and holding the button, it's blinking like it is counting seconds - always at the 3rd blink, is stopping.

Same as my problem

fans20f68474 Posted at 9-28 06:26
Where I can share a video
I wanna send video for my pairing mode problem

Hi there, you may share us the video here. Kindly upload the video to a video hosting site like SkyPixel or Youtube, then just put the link here at DJI Forum.

Thank you for your understanding and support!

fans20f68474 Posted at 9-28 06:27
Same as my problem

Hi there,
thank you for reaching out.

Kindly inform us the full details of the issue that you experienced with your DJI product, and we will surely provide you with an accurate resolution after we review the details. Rest assured that we're committed to providing the best experience for our users.

Please keep us posted. Thank you for understanding.

No matter how long pressing the power button it won't go to pairing mode anymore

fans20f68474 Posted at 9-28 06:21
Cannot enter pairing mode

You actually expect warranty support after doing those modifications?

d.buzdugan Posted at 3-16 23:08
Unfortunately, it doesn't enter in the pairing mode/blinking sequence.

While I'm pressing and holding the button, it's blinking like it is counting seconds - always at the 3rd blink, is stopping.

me toooo i have the same issue

JeremyB31 Posted at 9-30 15:26
You actually expect warranty support after doing those modifications?

i don't ask for warranty i just want it to work again what should i do never ask for warranty

DJI Natalia Posted at 9-30 00:26
Hi there, you may share us the video here. Kindly upload the video to a video hosting site like SkyPixel or Youtube, then just put the link here at DJI Forum.

Thank you for your understanding and support!

https://drive.google.com/file/d/1FYMfF0wNojNzF7gjVXGyP4UhI5rC_kWq/view

DJI Paladin Posted at 3-16 21:56
Hi there. Thank you for reaching out and we do apologize for the trouble. After pressing the link button on the Goggles. The Goggles will start to beep as it indicates that it entered linking mode, you need to "PRESS AND HOLD" the power button on the aircraft until the battery level LEDs start to blink in sequence. If the issue persists, please record a short video showing the problem and send it to us so we can check it further. Please keep us posted.

https://drive.google.com/file/d/1FYMfF0wNojNzF7gjVXGyP4UhI5rC_kWq/view

fans20f68474 Posted at 10-27 11:19
https://cdn.djivideos.com/video_play/d4f36eae-9ea0-44e5-825a-167f40ac4cdd
https://drive.google.com/file/d/1FYMfF0wNojNzF7gjVXGyP4UhI5rC_kWq/view

that sucks, hope for an update from DJI for u guys

fans20f68474 Posted at 10-27 11:19
https://cdn.djivideos.com/video_play/d4f36eae-9ea0-44e5-825a-167f40ac4cdd
https://drive.google.com/file/d/1FYMfF0wNojNzF7gjVXGyP4UhI5rC_kWq/view

HI there, thank you for sharing this video. May I cofnirm if the firmware is updated to the latest version in both your aircraft and remote conctroller? If not, kindly update the firmware or rferesh the firmwar to the latest verison vis DA2. Also, please cofnirm whether there is an SD card installed in the aircraft. If yes, please remove the SD acrd and try enter the binding state again then check if the issue still perists.

Keep us posted and thank you for your understanding.

Thank you for your suggestion. I'll try removing the SD card and try the firmware. I'll make a video of the process to ensure everything is documented. If there are any further issues, I'll let you know. Thanks for your assistance.

Having the same problem, ive tried bindint to a controller, motin controller and googles, the problem is the avata dosnt enter mind mode. holdint the button dosnt work. someone in the comments said to try with the battery disconnected, i get the same responce, this make me wonder could it be the battery firmware ? if so how do fix that ?