New firmware for Mavic Pro has been released（04/05/2017）

CAAirborne

Linsenfest Posted at 2016-10-21 01:23
Hmm still no update on my ios app.
Or is this a mavic firmware update?

[removed by poster]

bunny too

Ivan7 Posted at 2017-2-14 08:31
Looks like I have the same issue you mentioned. It will not switch off after charge completed when charging without the hub. I will add my comments into your other thread.

When this happend to me, I installed in the Mavic, turned on, turned off and plugged back in charger and the lights turned off after a few minutes.
Regards,
-d.

CAAirborne

[removed by poster]

M Cubed Media

Now I am confused, I am reading some posts that mention the batteries need upgrading, how do you do this?

I was under the impression that if you do the update when prompted, it sorts out all the updates on the RC, the Mavic as well as on the batteries.

If this is not the case, how do I do updates on the batteries?

Airwolf13

My upgrade went perfect No issues About 20m

bitboy0 - mavic

bunny too Posted at 2017-2-14 08:58
When this happend to me, I installed in the Mavic, turned on, turned off and plugged back in charger and the lights turned off after a few minutes.
Regards,
-d.

You allways can switch off the battery like when you do at the end of a flight. But this is nevertheless an error. Also it seems that this particular batteries do NOT accept any FW-upgrades and also not report their FW-version correctly to the mavic. I would appreciate if you also report your battery here:
forum.dji.com/forum.php?mod=viewthread&tid=84995

This is something that might be a problem in the future and it's better to take care about before any problems occure!

Jdwyier

Upgraded Mavic and RC this morning. Took it out and ran through a battery with it. No problems with the new firmware were seen. I have not run through every possible scenario yet by any means though but so far seems solid. Will be doing some further testing with the various flight modes and doing some video with the new D-log settings to see if I can detect better dynamic range in that video mode.

RichJ53

fansc81e6605 Posted at 2017-2-14 05:40
I just installed this update - now my Mavic seems to stray a little when the controls are not being touched!
Not windy with plenty of satellites locked on? Suggestions?

Calibrate the compass and try again

Rich

c_future

M Cubed Media Posted at 2017-2-14 09:20
Now I am confused, I am reading some posts that mention the batteries need upgrading, how do you do this?

I was under the impression that if you do the update when prompted, it sorts out all the updates on the RC, the Mavic as well as on the batteries.

Hello

I updated from the latest version before (from end of december) via dji assistant.

Afterwards plugging in all my batteries and connecting the app to check if battery update is needed.

but this time no update gets displayed.

so i guess there is none with this firmware compared to the one before?

bitboy0 - mavic

The Update resets some Settings:
EXP, settings are back to 0.25 for all three (I like 0.20 for me)
Camera goes to "JPG-Only" where I had "JPG+DNG"
I had the feeling that decent is faster in GPS-Mode than before
I had to calibrate the sticks also.

bitboy0 - mavic

c_future Posted at 2017-2-14 10:39
Hello

I updated from the latest version before (from end of december) via dji assistant.

in my case there was a popup after restarting the mavic, the RC and the app "firmware inconsistant" and an option to upgrade. This appears for each battery once. The Update that takes only a few seconds and than it's done.

Roli6

c_future Posted at 2017-2-14 10:39
Hello

I updated from the latest version before (from end of december) via dji assistant.

My batteries also didnt get a update.

R&L Aerial

While hooked up to DJI assistant after upgrading firmware replace each battery and click refresh, it only takes a few minutes for each battery.

Frits48

Updated the firmware this morning. Was completed in about 15 minutes. No message to repeat from either of my 2 batteries.
Had 2 lengthy flights later today without any issues.

Bursky

Updated without a hitch from the IOS app in 16 minutes from start of download to the finish of Firmware installation. No update for additional batteries.

Col-Drone

I attempted to upgrade but the upgrade process became stuck at 67% (for about 10min to 15min). Turned everything off and back on again. Second time it worked. One possibility, during the first attempt I forgot to remove the ND filter from the Mavic. The filter was removed and attempted the process again. Using latest versions of iOS and RC.

Just my $0.02 worth. YMMV.

ah93

how can i check what version mine is on? came up failed update rebooted and tried again but the prompt to update didnt appear, under aircraft status everything is normal

danieleforyou

Col-Drone Posted at 2017-2-14 12:30
I attempted to upgrade but the upgrade process became stuck at 67% (for about 10min to 15min). Turned everything off and back on again. Second time it worked. One possibility, during the first attempt I forgot to remove the ND filter from the Mavic. The filter was removed and attempted the process again. Using latest versions of iOS and RC.

Just my $0.02 worth. YMMV.

Did you upgrade via Go 4 app or Assistant 2?

Gateway

Do these firmware updates still wipe out all your settings in the go app? I get so annoyed with having to reset up everything again.

Col-Drone

danieleforyou Posted at 2017-2-14 13:27
Did you upgrade via Go 4 app or Assistant 2?

I used the Go 4 App.

CAAirborne

bitboy0 - mavic Posted at 2017-2-14 10:44
The Update resets some Settings:
EXP, settings are back to 0.25 for all three (I like 0.20 for me)
Camera goes to "JPG-Only" where I had "JPG+DNG"

Thanks for the info. I also noticed that it resets (turns off) the flight change mode (may have the terminology wrong), which allows going from Normal to Sport mode during flight.

PS: Just updated the FW and flew a couple of batteries. No issues.

daivatam

when will come the next firmware...the real one with problem solved and improvements?

boostedford

is that seriously all they changed after a month and a half?? r u serious????? WOW. im not updating yet to see if anyone has any problems but wow thats so messed up!!

CTKgolfboy

Do not update, constantly disconnects from the drone. The app doesn't crash, it simply disconnects. I was 1000 feet away, thankful return to home worked. Beyond frustrated with my mavic pro thus far.

fansbb07b05f

A real critical update is to make the Mavic CSC the same as the Phantom 4 (pull the left stick to the bottom inside corner while simultaneously pressing the RTH button). DJI should do this as a priority. In the case of the Mavic it would be to pull the RIGHT stick to the bottom inside corner because the RTH button is on the left side of the remote.

bunny too

ah93 Posted at 2017-2-14 12:52
how can i check what version mine is on? came up failed update rebooted and tried again but the prompt to update didnt appear, under aircraft status everything is normal

Go to the... Buttons then... (three dots) again, then the "about" tab.
Regards,
-d

aguilera_br

You guys know about 3DLut files for Mavic? Before latest firmware release it was in DJI's webpage for download. Now I can't find it anymore.

Fiveform 2

I had an issue with this upgrade and many previous ones, using DJI Assistant 2. I upgrade successfully, but then when I connect to app and RC I am given the update notification again and have to repeat the process from the DJI Go4 app. Note that this is not an update of the RC, but of the Mavic and the time is about the same - 20 minutes or so to download and update Mavic.
My question is, why is DJI Go4 (latest Android version) no recognizing the firmware update done with DJI Assistant 2?

fansa4d1bef7

I recently received my Mavic Pro and it had the v01.03.0300 firmware installed. I tried to upgrade to v01.03.0400 through DJI Assistant 2. It looks like everything is going smoothly, and the screen says I'm upgrading to v.01.03.0400. After 100% is reached, the screen tells me I've successfully installed v01.03.0300! It then tells me that I need to upgrade to v01.03.0400 and prompts me to upgrade. I've tried this three times, each time shutting everything down and restarting, but I get the same result. Am I doing something wrong? Each attempt to upgrade, after what appears to be a successful upgrade, it shows my current version is still v01.03.0300.

Watty2000

Looks like the gimbal tilt using C1 and the exposure dial to adjust gimbal roll seems to be working as expected now, on iOS anyway.

Thermo614

I've never had luck upgrading the firmware. I am on 1.3.000 and can go no further. I was happy to see today's update, thinking that maybe the 200 update was my problem. Same issue with this version. However, I have seen that i may need to do a complete format of my SD card and install a bin file? I emailed DJI to see if I can get this file.

Silverado101980

Upgraded and lost the ability to change the camera EV setting with the right roller but now it's able to be changed like my old Phantom 3 standard was on the phone I have Android version

DRONE-flies-YOU

D-Log now looks really, really good. The dynamic range has DEFINITELY been increased, as advertised! I couldn't believe how "far" I was able to push some of the sliders in post with today's footage on firmware .0400.

mcd0nald

*arghhh* hope I could get my mavic replacement updated with latest version already!!!

hungdang

fansa4d1bef7 Posted at 2017-2-14 17:46
I recently received my Mavic Pro and it had the v01.03.0300 firmware installed. I tried to upgrade to v01.03.0400 through DJI Assistant 2. It looks like everything is going smoothly, and the screen says I'm upgrading to v.01.03.0400. After 100% is reached, the screen tells me I've successfully installed v01.03.0300! It then tells me that I need to upgrade to v01.03.0400 and prompts me to upgrade. I've tried this three times, each time shutting everything down and restarting, but I get the same result. Am I doing something wrong? Each attempt to upgrade, after what appears to be a successful upgrade, it shows my current version is still v01.03.0300.

try to downgrade to 200 then upgrade to 400

Jenee 2

If I can, I will go back to the 200 firmware as a few problems with 400 that I don't like. Just seems inconsistent. After doing the upgrade to both Mavic and controller and then checking everything including all batteries, everything seemed fine. Flew today and and tried the RTH and although it was facing toward the sun, the sun was higher than the camera but it still went crazy, up, backward, heavy braking. Flew home manually. Found in the Healthydrones logs that during the crazy RTH it lost the data link 3 times. I am not surprised with the way it was flying.
Next flight when app opened said it needed firmware update which was quick and probably the battery. Next flight when app opened, needed firmware update and this time the controller disconnected a couple of times during the update. I now feel nervous flying on this firmware. Not sure what has been done but the sensors are just not working correctly.

4wd

DRONE-flies-YOU Posted at 2017-2-14 19:34
D-Log now looks really, really good. The dynamic range has DEFINITELY been increased, as advertised! I couldn't believe how "far" I was able to push some of the sliders in post with today's footage on firmware .0400.

I was hoping to hear this, can you post a video?

eskape

DRONE-flies-YOU Posted at 2017-2-14 19:34
D-Log now looks really, really good. The dynamic range has DEFINITELY been increased, as advertised! I couldn't believe how "far" I was able to push some of the sliders in post with today's footage on firmware .0400.

What are your picture settings? (Sharpness,Contrast,Saturation)
And are you over-exposing at all?

Thanks for any help

CCD1024

Hello
I received my Mavic 1 week ago in version 1.03.0300 and I tried to update 1.03.0400 but it was a nightmare.
1rt I did the update under Dji GO 4 Android. All was fine but stopped at 73%. Then, impossible to go further, even rebooting all !
I tried many time Dji Assistant 2. Error after 55%.
I was able to downgrade in 1.03.0200 (Mavic & RC). Than I tried again update with 1 hour with Tchat Dji support... no way.
This morning, I tried again under Dji assistant : no way
Then tried again under Android ! Error, then impossible to connect to Mavic (only the RC) , but I relaunch the update and it worked !!!! Now both are 1.03.0400 !
I will check tonight with Dji Assistant for batteries

... a nightmare evening !!!! Nice st-valentin

Essence

Tried to update to the 400 firmware 2 times with GO 4 on android. Could upload the firmware, but could not complete the updating.
The Mavic restarted itself 3 times during each update attempt, and on the 3rd time (every attempt its the same), the updating stopped at 73% and it says "UPDATING FAIL"
Try plugging the RC into my PC with Assistant2, my PC could detect both the RC and Mavic. Hence i'm kinda stuck with GO 4 updating.

Gonna try again a IOS to see if it works. So Frustrating!