New firmware for Mavic Pro has been released（04/05/2017）

phil_r

Heavysledz Posted at 2017-4-16 16:02
Tested earlier today and video cache is working on my iPad mini 2.

Thanks for that info. I have offended something in my quad. I can't get the video cache to work on my mini 4 using firmware .400, .0550 and .0600 and DJI Go4 v4.06/4.07 with firmware .0600.

Jenee 2

There is one thing I have found with the latest .0600 update which I have not seen before. On all previous updates, after turning everything on, I normally wait to make sure I have full GPS and previously, this happened reasonably quickly. On the latest update, it starts in ATTI then briefly show GPS mode then switches to OPTI and stays there for almost a minute. Then it goes back to GPS mode and is stable after that. I don't know if this is happening to other people, but some new users may see the GPS briefly and takeoff before it has really locked into GPS mode. There is nothing in my logs to show that it is doing this as the logs only seem to start when the motors have started and by that time I have full GPS lock.
I don't think it is a fault in my Mavic because I did not have this happen on .0550.

lhabdullah

I have an issue with this firmware. At first I updated it and it said update completed. However, the next day I got a message that a new update available but it is exactly the same update. So I have to do the process twice for the same update.

Asainz320

After upgrading last night, my gimbal randomly started rolling by itself. My video feed started rolling slowly and then I looked at the gimbal and it was slowly rolling by itself. Im assuming this was caused by the new Fixed Wing mode, so I did a gimbal calibration and I see that now the gimbal calibration takes a long time as before but now it does some extreme rolling which I had not seen before. After the calibration I think its better but I will have to check some more.

Something I can say is that I did a quick flight last night and it seems that the horizon tilt has been fixed!! Again, I will need to do more testing, but as far as I could tell from my very short flight, when I started flying sideways the horizon stayed pretty level. I will post my findings later on.

Heavysledz

phil_r Posted at 2017-4-16 20:00
Thanks for that info. I have offended something in my quad. I can't get the video cache to work on my mini 4 using firmware .400, .0550 and .0600 and DJI Go4 v4.06/4.07 with firmware .0600.

Have you deinstalled the app completely and then reinstalled it?

fans95824758

Hi, I have had today a little issue with my mavic flying with the new firmare .600. It has taken off without any problem, has ascended to 50 m, I have flown it 135 meters away and it has appear the message "Aircraft disconnected" on the app. I had control over the aircraft and I have been able to bring it back to home, but the rc was making something strange, the screen on the rc was going and coming, this had not happened before. Is it something related with the new firmware? Just leave it here in case it interests to someone.

Gallacherboy

Hey guys, last night I updated to v01.03.0600 and as always I used DJI Assistant 2 on MAC to download and update the Drone and controller individually. Never had problems when updating, only updated via the DJI GO 4 App only once. After ever update I Refresh the update and reset all my camera settings. Might as well do it as you have to reconfigure all your settings again.

I noticed that the start up melody is back to normal, no echo like sound when starting up - Good job DJI

I ran a Gimbal Auto-Calibration and it did a lot more then pan and tilt. I noticed a lot more activity. Also starting up, the Gimbal does not thrash itself about when starting up. My horizon was PERFECTLY LEVEL. When coming out of SPORT MODE, the horizon is a little off, i am sure most of you know the shortcut to doing a mid flight correction by holding down C2 and using the Shutter wheel to set your horizon level. I have to say it works well this time, I made slight adjustments and the changes were precise.

The last time I flew on v01.03.0550, I did notice the Mavic drifting a lot but maintaining its position. Mavic sounded louder and also batteries drained faster, even when flying - not hovering.

I am very happy with v01.03.0600, well done DJI

phil_r

Heavysledz Posted at 2017-4-17 08:33
Have you deinstalled the app completely and then reinstalled it?

Yes I did that and when I got no joy there. I uninstalled again and installed an earlier IOS version of DJI Go4. I won't be flying for a week but I think my next test may be to backup and then wipe my iPad and just install one fresh copy of the app and see how that goes.

blunt_blunt

Tip: the author has been banned or deleted automatically shield

Heavydpj

blunt_blunt Posted at 2017-4-17 16:24
I suppose one out of 5000 is pretty good.
Everyone else thinks .600 stinks and for that reason i wont be a guinea pig yet again.
So sick and tired of DJI stuffing up my drone.

Unless you're one of the 5,000 (like me)"

Then it sucks. I had to send mine in for "repair" due to repeated failures to update.

Morphin

Heavydpj Posted at 2017-4-17 18:21
Unless you're one of the 5,000 (like me)"

Then it sucks. I had to send mine in for "repair" due to repeated failures to update.

I too sent the item for "repair" only because it does not update to 600.

everyhing is fine except update to 600.......

I suppose that a Hardware-Change could be the reason for that..... Hopefully DJI is investigating this

Andy

srock

New Mavic- previously used DJI Go3 on my iphone 5 without any difficulty until DJI without warning dropped support and forced me to get a new phone (ios) to use DJI 4 which does not seem to work

I have not upgraded firmware yet- I do have DJI GO4 ios v. 4.07- I have installed the desktop assistant- Any consensus as to which firmware provides a stable platform until DJI gets its act together and puts out new stable firmware. Many people seem to be sticking with .400. Is that the best so far ? Will that firmware be OK with newer DJIGo updates?

Steve

/// AROP

release notes should mention now recording sound

MuriloBarroso

I have been having Gimbal issue. Out of the blue the gimbal would shake hard. The first time I thought I had hit something in mid fly. But it wasn't. It was the gimbal doing crazy things. This all started after that last firmware update. I have called DJI. They want me to send in the drone. But I know it isn't anything physical since like you I never crashed or even came close to crash. Anyone have any options to fix it.

I believe this is happening every time you hit the focus button.

One more thing every time this happens it stops recording I was only able to get this footage because I was live streaming to YouTube when it happened.

Here is the video.

Gallacherboy

Does anyone Refresh their Firmware after installing?? When I received my Mavic, I had video issues and I was convinced it was a hardware problem but actually Refreshing the firmware fixed my it. Every time I install I switch it off and run the installation again and I never update via the DJI Go 4 App, always DJI Assist

John12341234

Just bought a Mavic pro, firmware update is stuck at 51%. I think my phone is an iphone SE. Looking right now on downloading assistant 2 for windows. Anyone else stuck at 51%, anything I can do to fix?

Luka M

Just joined the forums, could anyone suggest updating to this firmware or not due to any possible faults in it. Just recently got mine and my current firmware seems all fine so don't want to get this new one to find it's faulty and crash my mavic.

Craig540

MuriloBarroso Posted at 2017-4-18 17:52
I have been having Gimbal issue. Out of the blue the gimbal would shake hard. The first time I thought I had hit something in mid fly. But it wasn't. It was the gimbal doing crazy things. This all started after that last firmware update. I have called DJI. They want me to send in the drone. But I know it isn't anything physical since like you I never crashed or even came close to crash. Anyone have any options to fix it.

I believe this is happening every time you hit the focus button.

I had the same thing happen but its with high wind flights. I have even seen it on the ground with high wind. Are you flying with a gimbal cover or was this without any cover. If no cover try it with a partial cover.

John12341234

John12341234 Posted at 2017-4-20 22:06
Just bought a Mavic pro, firmware update is stuck at 51%. I think my phone is an iphone SE. Looking right now on downloading assistant 2 for windows. Anyone else stuck at 51%, anything I can do to fix?

It works now, recharged iphone next day, went on the app and it looks like the update did finish even though it appeared to be stuck at 51%.

dEEr

Updated to lastest firmware couple of days ago. Since then, several problems appeared:

- iPhone6S doesn't charge up any more. When it's connected to the remote, it shows up "charging" but it just don't charge.
- Rondom Gimbal Error / Losing Gimbal/Camera Settings during flight. After 5-6 min. of flight time, the camera/gimbal is losing the settings for about 10-15 sec. In the App it just shows "N/A" for every camera/gimbal settings. The gimbal is not stabilizing, camera falls down. After 15 sec, settings were up again. By the way, the drone itself is still controllable during this time.

I just dont recommend to upgrade to the latest FW! Trying to downgrade my now -.-

Never had an issue with my mavic before -.-

Dirk52

iPhone gets never charged on RC..
No matter which fw.

Irmantast

Why first post is not updated with Firmware : v01.03.0600 version? It means update is not ready or what?

NicoNic

So is this FW stable or not ?

jameswan

Have no issue with FW update.

fanseb821119

NicoNic Posted at 2017-4-24 07:38
So is this FW stable or not ?

for me it's working great.
no issue during the update
and during flights

Bintryin

NicoNic Posted at 2017-4-24 07:38
So is this FW stable or not ?

I would say NOT!!!!

fallsilent

NicoNic Posted at 2017-4-24 07:38
So is this FW stable or not ?

Updating was simple and everything works great for me. No issues.

WalkingToFlying

Hi Im on latest firmware on MP, RC and GO4 app on android. So far so good. Brought the MP for test flight with the new FW a couple of times and it wirjs great. Using my old Note 4 hp. Quite wary of the latest FW update issue as mentioned in here.
Hope I the issue won't affect me n my equipment here in Singapore.

tanakrit

FW.600 can push up the left stick for cancel auto landing?

I have been waiting for a long time for the safety landing.

fans1109ab43

Updated to FW.600. All is well, the download is smooth, the installation has no issue and the test flight this morning works well. Using Android phone Xiaomi 3S with Marshmallow 6.0.1 to pair with the RC. Updated using the RC with DJI GO App via my phone. Tried the fix-wing mode too and its works all right.

Minor issues are: 1) after the FW.600 update, it tried to update the NFZ but the DJI GO app hanged... maybe its my phone overheated right after the update as the Wifi and LTE both become very unstable, and 2) on my 2nd battery, I can't seem to switch to fix-wing mode... need to read up a bit more on this and try again next time. 1st battery have no issue with fix-wing mode though.

PushSky

I flew with the FW.0600 for the first time today with some issues. Regular start up procedure with no errors or warnings. GPS mode with 12-14 satellites. I had a lot of drifting that required inputs to keep the drone in place. This was a first as the Mavic has been rock solid when flying .0400 and .0550 FW. It also lost GPS lock once in the sky. There are no building or obstructions to that would block out GPS signals so it was a little unusual. Then it went into ATTI mode. It was a little breezy (maybe 10 mph) so flying became a lot more stressful. This happened twice and on the second flight the drone was difficult to control with the breeze. I've rolled back the FW and will see if the Mavic behaves as it had in the past.

I was looking forward to the new flight modes and improved video capture but the random GPS signal loss definitely out weighs any improvement in video capture quality.

Flybee

I was investigating what version I have on the Aircraft and in DJI assistant it says for the .600 version "refresh" and current for .055 or lower it says "downgrade" my interpretation is that i'm on .600. When I start the DJI GO app it says that .600 is available for upgrade.

How should I interpretate the information?

patman89

Flybee Posted at 2017-4-30 00:43
I was investigating what version I have on the Aircraft and in DJI assistant it says for the .600 version "refresh" and current for .055 or lower it says "downgrade" my interpretation is that i'm on .600. When I start the DJI GO app it says that .600 is available for upgrade.

How should I interpretate the information?

Have you upgraded your remote controller? If not, this is why the information pops up ;-)

Just connect your controller to your PC, turn it on and launch DJI Assistant 2. You can connect your controller via Micro USB (same port which is used for charging your controller).

PushSky

PushSky Posted at 2017-4-29 19:34
I flew with the FW.0600 for the first time today with some issues. Regular start up procedure with no errors or warnings. GPS mode with 12-14 satellites. I had a lot of drifting that required inputs to keep the drone in place. This was a first as the Mavic has been rock solid when flying .0400 and .0550 FW. It also lost GPS lock once in the sky. There are no building or obstructions to that would block out GPS signals so it was a little unusual. Then it went into ATTI mode. It was a little breezy (maybe 10 mph) so flying became a lot more stressful. This happened twice and on the second flight the drone was difficult to control with the breeze. I've rolled back the FW and will see if the Mavic behaves as it had in the past.

I was looking forward to the new flight modes and improved video capture but the random GPS signal loss definitely out weighs any improvement in video capture quality.

Update: Rolling back to .0400 didn't change the GPS signal loss. After taking the cover off (voiding warranty again) I found the wires running to the left rear motor had popped out of the clip/guide and were resting closer to the GPS wiring. After tucking the wires back into the holder and making sure they we as far away as possible from the GPS assembly wiring my old rock solid Mavic is back! Flew for 20 min. without a single issue. Just to be clear I've crashed 3 times so far (steep learning curve) so the wires most likely came loose during my last uncontrolled landing. At this point I can give a thumbs up for .0600.

Flybee

patman89 Posted at 2017-4-30 12:21
Have you upgraded your remote controller? If not, this is why the information pops up ;-)

Just connect your controller to your PC, turn it on and launch DJI Assistant 2. You can connect your controller via Micro USB (same port which is used for charging your controller).

Thank you.

I have't upgraded anything got my machine back from repair and have not changed anything.

patman89

Can anyone tell me how to refresh the firmware? Some of you mention this, but never saw an option to do this? Or do you mean a factory reset?

Still trying to get .0600 on my mavic - with no success so far.

My next question: has anyone some details about the next update? .0650 or .0700? Or how is the upgrade cycle? Can we expect a new update anytime soon? So I would try to skip .0600 :-)

saback

patman89 Posted at 2017-5-2 06:16
Can anyone tell me how to refresh the firmware? Some of you mention this, but never saw an option to do this? Or do you mean a factory reset?

Still trying to get .0600 on my mavic - with no success so far.

I had some hiccups to upgrade to the new FW. I got mine few weeks ao and I jumped from the original FW straight to FW .600

I tried the DJI GO 4 app but it stuck first at 0% and later at 5% and didn't progress so I decided to use the DJI Assistant what didn't work first time. The process I follow was:

MP

Upgrade

Factory Reset

Refresh

Remote Control

Upgrade --> worked first time

I'd recommend you to try few times with different setups - MP only, RC only, MP + RC, or as a last resort try to install the previous FW and upgrade from it.

Kronos69

I suggest to NOT upgrade to 600. It literally bricked my new (few minutes lifespan) Mavic. Waiting for a response better than "we'll repair it", for a brand new drone. A lot of other people are complaining about update interruptions, etc.

tanakrit

This time, FW.600 makes me feel good. Like when it was new.
Thanks dji for good support.

patman89

Kronos69 Posted at 2017-5-2 16:29
I suggest to NOT upgrade to 600. It literally bricked my new (few minutes lifespan) Mavic. Waiting for a response better than "we'll repair it", for a brand new drone. A lot of other people are complaining about update interruptions, etc.

As long as my .0550 firmware runs well, I don't need to update. But I have concerns, that this issue persists in future updates :-(

blunt_blunt Offline blunt_blunt Ban Posts + Add Friend Person Message Australia Offline	Tip: the author has been banned or deleted automatically shield

	2017-4-17 Use props