I just received my P4P. It all seams good except for the remote won't calibrate. Every time I start it up it blinks red and beeps non stop until I go into the app open the error message read that the remote needs calibration. Shut the aircraft off, open the remate settings on the app start the calibration process. get a warning. Click ok hit start and start to move the sticks to the max in all directions but never see the pecentage go up from zero or get a finished signal. if I close the calibration setting at this time and restart the aircraft all is good but next time I resart the remote the f*****ing beeping starts again. WTF!

I'm having the same exact problem. I just updated the new Firmware today but I don't know if that has anything to do with it.

Make sure the firmware is up to date, then try to calibrate it again. If it is still the same, please post a short video about this issue for better assistance.

According to DJI4 Go the firmware is up to date. Is there anyway to reinstall the new firmware? Maybe there was a glitch in the update or the process.

DericsDad Posted at 2017-7-20 23:20
I'm having the same exact problem. I just updated the new Firmware today but I don't know if that has anything to do with it.

Ivan,t say for certain because I never used mine with the old firmware. I did do the update when prompted so it could be. Very annoying, that constant beeping is enough to make you crazy.

According to the online support, I am to try reset the controller. I'll keep you posted if it works or not. Fingers crossed but not holding my breath.

Performed the reset function C1 C2 shutter button turn off hold the buttons turn back on same issue.

JF West Coast Posted at 2017-7-21 15:10
Performed the reset function C1 C2 shutter button turn off hold the buttons turn back on same issue.

Have you tried to reset it via DJI Assistant 2?  You can try the steps below , see if the firmware can be re-installed.
1. Power on the RC and connect it to your phone;
2. Open the APP, press and hold the icon on the right top corner for 5 to 10 seconds, then let it go;
3. A black page will pop out, see if you can download the firmware and re-upgrade it on this page.

Thanks I'll give that a try but I'm learning towards returning it for a replacement. I believe when you buy something new it should work.

DJI Diana Posted at 2017-7-22 01:36
Have you tried to reset it via DJI Assistant 2?  You can try the steps below , see if the firmware can be re-installed.
1. Power on the RC and connect it to your phone;
2. Open the APP, press and hold the icon on the right top corner for 5 to 10 seconds, then let it go;

Hi I am having the same issue - as soon as I downloaded the latest firmware upgrade it started doing this. I have followed your instructions however in the select firmware version it has NONE. I hit the download button to try and reinstall but nothing happens?

the version the remote is operating on is 1.9.3 Product GL300 Remote Controller

the following appears underneath the download button 144A0615_362B_4944_B408_06E4C0530B48???

Can you please advise?

fans3fcdf823 Posted at 2017-9-29 19:18
Hi I am having the same issue - as soon as I downloaded the latest firmware upgrade it started doing this. I have followed your instructions however in the select firmware version it has NONE. I hit the download button to try and reinstall but nothing happens?

the version the remote is operating on is 1.9.3 Product GL300 Remote Controller

Hi DJI Diana,

Yes I tried that it has not assisted, is there any other way to deal with this issue or will it be fixed in the next firmware update?

thanks.

fans3fcdf823 Posted at 2017-9-29 19:18
Hi I am having the same issue - as soon as I downloaded the latest firmware upgrade it started doing this. I have followed your instructions however in the select firmware version it has NONE. I hit the download button to try and reinstall but nothing happens?

the version the remote is operating on is 1.9.3 Product GL300 Remote Controller

The firmware is up to date, have you tried to calibrate the Remote Controller?

Same problem. I can still fly. But can't recalibrate.