Please select Into the mobile phone version | Continue to access the computer ver.
Is the H3-3D Suppose to point directly down?
3729 12 2014-10-15
Uploading and Loding Picture ...(0/1)
o(^-^)o
Karsten116
lvl.1

United States
Offline

Is the H3-3D gimbal suppose to point directly downward? All the youtbe videos I have seen shows that is does. but mine does not?
2014-10-15
Use props
Blade_Strike
Super Moderator
Flight distance : 872694 ft
  • >>>
United States
Offline

yes you should be able to point straight down. I would start with an x1 calibration and go from there.
2014-10-16
Use props
Karsten116
lvl.1

United States
Offline

Blade_Strike Posted at 2014-10-16 22:37
yes you should be able to point straight down. I would start with an x1 calibration and go from ther ...

ok yeah I thought so.
Yeah i already did that and still haven't had any luck...
2014-10-16
Use props
etirado
lvl.1

Puerto Rico
Offline

Did you check the end points on your control?
2014-10-16
Use props
Karsten116
lvl.1

United States
Offline

etirado@sssandf Posted at 2014-10-17 02:21
Did you check the end points on your control?

what do you mean? like on the remote controller?
2014-10-16
Use props
etirado
lvl.1

Puerto Rico
Offline

On your remote control, you should check the end points on the channel used for the tilt down. Usually it is channel 7 if you are using Futaba.
2014-10-16
Use props
DJI-Cathy
Second Officer

China
Offline

please calibrate your X1 with the Assistant Software
2014-10-16
Use props
Karsten116
lvl.1

United States
Offline

DJI-Cathy Posted at 2014-10-17 14:20
please calibrate your X1 with the Assistant Software

i already did that....
2014-10-17
Use props
Tahoe_Ed
Administrator
Flight distance : 2605 ft
  • >>>
United States
Offline

Make sure that your endpoints are set at 100% then calibrate.
2014-10-17
Use props
Karsten116
lvl.1

United States
Offline

Tahoe_Ed Posted at 2014-10-18 03:26
Make sure that your endpoints are set at 100% then calibrate.

i finally got iy working after some differnt adjustments. thank u tho
2014-10-22
Use props
guitarian
lvl.2

United States
Offline

Karsten116 Posted at 2014-10-23 02:43
i finally got iy working after some differnt adjustments. thank u tho

I'm having the same issue. I've done a calibration (twice) and it still won't aim straight down. During the "pre" setup after powering up it does go completely horizontal but not by using the controller's slide lever.
What different adjustments did you do?
Also, is there a manual for the RC software? I can't find it on the DJI site.
Thanks
2014-10-27
Use props
lucking
lvl.1

Denmark
Offline

I had the same issue after gimbal firmware update - but suddenly after calibrating using first the RC software and then the Assistant software, it worked again. I was confused that the RC software states that the X1button is not calibrated there - but it had an impact though.
2014-10-28
Use props
markimus58
lvl.1
Flight distance : 6296 ft
United States
Offline

I just received a latest version P2 with H33D and 2312 motors directly from DJI and am using Hero 4B. Successfully performed Advanced Calibration. When H33D boots up it stays pointing straight down I have to use the control wheel to bring it to front facing. Is this normal?
Also, the stabilization in flight is great, however the horizon is not level by 2-4 degrees and drifts as yaw changes during flight.

How do I correct these issues?
2014-11-16
Use props
Advanced
You need to log in before you can reply Login | Register now

Credit Rules