This makes no sense.  I fly my route, setting waypoints along the way, then fly the "mission".  However, the drone points in a seemingly random direction.  I remember seeing a video that shows the ability to select options such as "free", "consistent with recorded" or "consistent with route", but these options were not presented to me when I finished recording.
I've check my version of DJI GO 4, and it's the latest.  FW and RC are all updated as well.
Any clues?

Thanks

You can choose the heading before applying the mission, please check this tutorial video and confirm.

DJI Susan Posted at 2017-10-11 22:13
You can choose the heading before applying the mission, please check this tutorial video and confirm.

Thanks for the reply.  I've viewed several videos showing this, BUT when I do it, I do not get the final dialog where I can select "consistent with record", "consistent with route" or "free".

cleamon Posted at 2017-10-12 01:30
Thanks for the reply.  I've viewed several videos showing this, BUT when I do it, I do not get the final dialog where I can select "consistent with record", "consistent with route" or "free". [view_image][view_image]

The window will pop up after setting the waypoints one by one. Then you can apply it. I would recommend you to start a new mission and check again.

DJI Susan Posted at 2017-10-12 20:18
The window will pop up after setting the waypoints one by one. Then you can apply it. I would recommend you to start a new mission and check again.

I have done several and it NEVER pops up.

cleamon Posted at 2017-10-13 09:05
I have done several and it NEVER pops up.

Please review the video tutorial provided in the previous response to make sure you are following proper procedure.

DJI-Mark Posted at 2017-10-13 09:08
Please review the video tutorial provided in the previous response to make sure you are following proper procedure.

I am following the procedures.  You don't seem to understand, I am not getting the same final dialog.  I just did it again.  During record, the only option is DONE.  Tapping DONE takes me to the next screen where the only options are CANCEL and APPLY.  There are NO options for "Head to:" or "Flight Mission Complete:" .I've tried to attach an image, but I guess I'm not important enough because after specifing the file, it returns to this post without attaching the file.
So here's a link to the image on my dropbox account:
https://www.dropbox.com/s/2vpg5gouktlt70e/DJIWaypoint.jpg?dl=0

cleamon Posted at 2017-10-13 09:05
I have done several and it NEVER pops up.

For what it's worth:
App Version: 4.1.10
Remote Controller: 02.01.01.00
Drone has the latest firmware installed as well: V01.00.0128

cleamon Posted at 2017-10-13 11:04
For what it's worth:
App Version: 4.1.10
Remote Controller: 02.01.01.00

What type of aircraft do you have? What type of mobile device do you have? What type of App do you have?  

DJI-Mark Posted at 2017-10-13 11:28
What type of aircraft do you have? What type of mobile device do you have? What type of App do you have?

Phantom 4 Advanced, DGI Go 4, Android Tablet

cleamon Posted at 2017-10-13 12:04
Phantom 4 Advanced, DGI Go 4, Android Tablet

I sent you a personal message. Please reply back to that message.

DJI-Mark Posted at 2017-10-13 12:21
I sent you a personal message. Please reply back to that message.

I've sent you a private message.  In short:
I have re-installed for the 4th time.  Recorded a waypoints mission and took screen shots.  As you can see, the options for "Head to" are not presented.  Here is a link to the screen shots: https://www.dropbox.com/s/ykvlz0e6tyos98z/DJI-BUG.jpg?dl=0

Ok.  I finally figured this out.  All of the videos I've seen, including the one suggested in this thread, say to tap "DONE", and then the options for "Head to:" will pop up.  However, with the version (4.1.10) of DJI GO 4 that I have (the latest for Android), you have to tap the "gear" icon on the upper right BEFORE you tap DONE.  Seems to be out of order to me, but at least I can now get to the options.

cleamon Posted at 2017-10-21 13:45
Ok.  I finally figured this out.  All of the videos I've seen, including the one suggested in this thread, say to tap "DONE", and then the options for "Head to:" will pop up.  However, with the version (4.1.10) of DJI GO 4 that I have (the latest for Android), you have to tap the "gear" icon on the upper right BEFORE you tap DONE.  Seems to be out of order to me, but at least I can now get to the options.

Aloha cleamon,

    Good to see you found a solution to the problem.  Be sure to change the title of this thread to indicate you solved the problem so others can look at what you did.  Something like [Waypoints view - Interesting Solution].

     Mahalo Nui Loa to DJI Susan and DJI-Mark for their help on this issue!

Aloha and Drone On!