DJI Phantom 4 - Since I installed the latest official firmware v.02.00.0106 and all 3 BETA available I am IMU Error. Calibrate IMU.

Every single time I load a firmware I run a Refresh for my 2nd battery and then a Restore Factory Defaults is done.
All calibration are performed as indicated: VPS using the DJI Assitant, Gimbal, RC and IMU.

I red other users are getting this error and as you can see in my video it will go away after a while. I am at the point where i would like to downgrade prior the faulty firmware to make sure the drone is running fine.
Today I had my first fly on Beta 0600 and I got a lot of Radio Interference. Flying above my subdivison and over a wooded area.

DJI, are you working on this error?

I can't see problem here, it's just warming up and you'd wait under 1 minute, it's normal

Vendex Posted at 2017-10-14 11:19
I can't see problem here, it's just warming up and you'd wait under 1 minute, it's normal

There was no imu Error message before the update just warming up message so it is down to firmware upgrade as myself and many other phantom 4 owners have experienced since the firmware upgrade

Vendex Posted at 2017-10-14 11:19
I can't see problem here, it's just warming up and you'd wait under 1 minute, it's normal

Johnny Mac 4 is right. Before the July update we had no IMU error message. I had the chance to fly the drone before  the v.02.00.0106 and you could only see IMU warming up. Nothing else. And that wasn't taking close to 2min.

It should the misinformation if the warning disappeared after the IMU warming up for a while. We are working on this and will fix it in the next official firmware.

DJI Susan Posted at 2017-10-14 20:06
It should the misinformation if the warning disappeared after the IMU warming up for a while. We are working on this and will fix it in the next official firmware.

Thanks DJI Susan. Still, it takes way longer for the IMU to warm up. I feel bad I didn't open a pool to see how many are having this issue.

I have the same problem

edith Posted at 2017-10-19 08:46
I have the same problem

Please vote on the poll I created. https://forum.dji.com/forum.php? ... p;page=1#pid1002609

For the first time I used my Samsung Galaxy 7 Edge and guess what??? No IMU Error on Android!!! I didn't see the Aircarft warming up message for long time. Is this iOS related? I will try it again and update the post.

I am confirming that the IMU Error appears only on my iPAD Air, iOS 11.02.
No issues on Samsung Galaxy S7 Edge, Android 7.0, DJI GO 4 ver 4.1.10. Warming up 1min 10sec vs 1min 4sec on iOS.

Same situation i updated the to 2.000.106 firmware and i get that same message then i went to calibrate and i get this message

Callatis Posted at 2017-10-24 16:04
I am confirming that the IMU Error appears only on my iPAD Air, iOS 11.02.
No issues on Samsung Galaxy S7 Edge, Android 7.0, DJI GO 4 ver 4.1.10. Warming up 1min 10sec vs 1min 4sec on iOS.

iPhone 7Plus iOS 11.02 appears with the same error to

BoriNinja Posted at 2017-11-12 10:36
Same situation i updated the to 2.000.106 firmware and i get that same message then i went to calibrate and i get this message
[view_image]

Basically you can try to refresh firmware again and give a try, if it's not successful again I suggest you to flash the current beta firmware 2.00.600 and also give it a try

No more issues with the latest version of DJI GO app for iOS. I didn't upgrade the firmware of my drone, still running the last Beta. I am afraid to upgrade to v02.00.0700