Since my last DJI firmware update my Phantom 4 flys in a very jerky fashion. I have reinstalled firmware two times as well as recallibrated IMU, compass and even turned off
all sencors.  It hovers and climbs perfectly. I also changed out the propeller mounts.  Any ideas?   

This is a known issue with the last P4 production firmware v...106.

You should PM a DJI admin here (DJI Thor, DJI Dianna and DJI Susan frequent here often) requesting access to the beta firmware v...600. This solves the erratic flying problem, as well as an issue recording video in 4K. You'll need to provide them with your DJI account email address to enable access.

Punchbuggy Posted at 2018-1-9 15:42
This is a known issue with the last P4 production firmware v...106.

You should PM a DJI admin here (DJI Thor, DJI Dianna and DJI Susan frequent here often) requesting access to the beta firmware v...600. This solves the erratic flying problem, as well as an issue recording video in 4K. You'll need to provide them with your DJI account email address to enable access.

Thank you Sir I will do so.......

Still awaiting update of firmware.  Help please!   Pnolis@yahoo.com.  

Hi fans5bafefc8
106 is far from perfect, but make sure you have the latest controller firmware,
   you still may get  warnings  when flying  strong winds  etc.   i think its due to the  flight instability  that is one of the issues with 106 firmware
with a bit of luck the next official firmware update will resolve the issue   when it comes  soon we all hope!

  

jkw Posted at 2018-1-12 15:10
Hi fans5bafefc8
106 is far from perfect, but make sure you have the latest controller firmware,
   you still may get  warnings  when flying  strong winds  etc.   i think its due to the  flight instability  that is one of the issues with 106 firmware

Hi. Which version of DJI GO 4 are you running? I think you’ll find that the wind warnings are the app, and not the firmware.

Punchbuggy Posted at 2018-1-12 15:28
Hi. Which version of DJI GO 4 are you running? I think you’ll find that the wind warnings are the app, and not the firmware.

hi im running  the very latest

jkw Posted at 2018-1-12 15:33
hi im running  the very latest

V4.1.22? OK. Hmm...

I did another firmware update yesterday to V02.00.0106 dated 2017-07-06.   The craft is essentialy unflyable. Hoover’s well but that’s it.  Have requested with Susan and Diana but nothing new on my Assistant 2. Am I doing this right?  Not a wiz at this!  

fans5bafefc8 Posted at 2018-1-12 17:25
I did another firmware update yesterday to V02.00.0106 dated 2017-07-06.   The craft is essentialy unflyable. Hoover’s well but that’s it.  Have requested with Susan and Diana but nothing new on my Assistant 2. Am I doing this right?  Not a wiz at this!

You need access to the beta .600, but there's a beta .700 now available to a closed test group. DJI appear to have removed access to .0600 as a result, which is not helping new people updating to the faulty .0106.

Ordinarily I'd be suggesting that you PM a request to DJI Susan, Diana or Thor with your  DJI account email.

Punchbuggy Posted at 2018-1-12 15:56
V4.1.22? OK. Hmm...

yep that’s the same vision i’m running  on an ipad pro  and  at the moment 106 on the drone

Punchbuggy Posted at 2018-1-12 20:01
You need access to the beta .600, but there's a beta .700 now available to a closed test group. DJI appear to have removed access to .0600 as a result, which is not helping new people updating to the faulty .0106.

Ordinarily I'd be suggesting that you PM a request to DJI Susan, Diana or Thor with your  DJI account email.

With no response from anyone, seems like my only option to regain proper functionality of my drone is just wait?
Wonder why I am not allowed access to .600 like others in this forum who have requested after me. I am starting to feel like Jerry Seinfeld in the “Soup Nazi” episode.  Lol.    “No Update for you..........  Next”!
Just saying.     

fans5bafefc8 Posted at 2018-1-12 17:25
I did another firmware update yesterday to V02.00.0106 dated 2017-07-06.   The craft is essentialy unflyable. Hoover’s well but that’s it.  Have requested with Susan and Diana but nothing new on my Assistant 2. Am I doing this right?  Not a wiz at this!

Hi it took 3 days  to come through for me

jkw Posted at 2018-1-13 13:10
Hi it took 3 days  to come through for me

Did they give you access to .600 or .700?

Punchbuggy Posted at 2018-1-13 13:30
Did they give you access to .600 or .700?

.700     now its asked me to calibrate the vision sensors , and in Dji Assistant2  i cant get the  calibration image  show !!!! , and looking at the forum i'm not the only one, my god i wasted some time with this P4 since the dreaded 106 update, before it was a dream of a drone.
  i did the quick calibration in the ipad go4 app, but it wants further calibration in Assistant 2.

jkw Posted at 2018-1-13 19:51
.700     now its asked me to calibrate the vision sensors , and in Dji Assistant2  i cant get the  calibration image  show !!!! , and looking at the forum i'm not the only one, my god i wasted some time with this P4 since the dreaded 106 update, before it was a dream of a drone.
  i did the quick calibration in the ipad go4 app, but it wants further calibration in Assistant 2.

most of the time the problem is in the monitor or the resolution of the screen

P4Mano Posted at 2018-1-14 02:51
most of the time the problem is in the monitor or the resolution of the screen

i've tried now all the imac screen resolutions , and still no joy ,  i have a newer imac and a mac book pro and that wont even identify the is a drone connected , ill keep battling  on  
many thanks   John

Sorry for the delay, we'll add the beta firmware to your account within 1 business day, your patience will be highly appreciated.

jkw Posted at 2018-1-14 07:53
i've tried now all the imac screen resolutions , and still no joy ,  i have a newer imac and a mac book pro and that wont even identify the is a drone connected , ill keep battling  on  
many thanks   John

John, have you tried to reinstall the DJI Assistant 2? If it persists, please try a windows PC if you can.

DJI Diana Posted at 2018-1-14 20:07
John, have you tried to reinstall the DJI Assistant 2? If it persists, please try a windows PC if you can.

Hi Diana     
yes i have  a few times  , i have a friend with an inspire 2  and a windows  PC   so ill try that on Wednesday    many thanks

I'm having the same issue. Great at low speeds but becomes erratic at higher speeds in all modes.  

jkw Posted at 2018-1-15 04:36
Hi Diana     
yes i have  a few times  , i have a friend with an inspire 2  and a windows  PC   so ill try that on Wednesday    many thanks

You are welcome, please keep us posted.

Nelsongc1@msn.c Posted at 2018-1-15 11:36
I'm having the same issue. Great at low speeds but becomes erratic at higher speeds in all modes.

Hi Nelsongc1, Which drone are you referring to? Have you tried to calibrate the IMU and check the propellers? Besides, what is the firmware version of the drone?

DJI Diana Posted at 2018-1-15 22:41
Hi Nelsongc1, Which drone are you referring to? Have you tried to calibrate the IMU and check the propellers? Besides, what is the firmware version of the drone?

Hi Diana,

I have a Phantom 4.  I have checked all The propellers and mounting plates and they are all secure.  The firmware/versions are:

App on Samsung S8 is 4.1.18
Aircraft firmware is 02.00.0106
R/C firmware is 1.9.3
I will try the IMU calibration and also use my iPad 4 mini.   But it didn't do it until after the update.  Is there away to do the firmware update again.  

Thanks,

DJI Diana Posted at 2018-1-15 22:41
Hi Nelsongc1, Which drone are you referring to? Have you tried to calibrate the IMU and check the propellers? Besides, what is the firmware version of the drone?

Diana,

I accomplished the IMU calibration and it didn't help.

Thanks,

DJI Diana Posted at 2018-1-15 22:39
You are welcome, please keep us posted.

I also have refreshed the firmware in DJI Assistant II and it did fix anything.  Still jerky in flight.  Wind in the flying area is 3mph, but it never did this even in 15mph winds.  Thanks for any help

Nelsongc1@msn.c Posted at 2018-1-16 15:15
I also have refreshed the firmware in DJI Assistant II and it did fix anything.  Still jerky in flight.  Wind in the flying area is 3mph, but it never did this even in 15mph winds.  Thanks for any help

It's a known issue with that firmware. You can request access to beta v...600 (try a PM to Susan of Diana with your DJI account email address), or wait until the next prod release which is hopefully not too far off (but who knows... ). There is a beta v...700  too, but only offered to a closed group of lucky few.

Punchbuggy Posted at 2018-1-16 15:45
It's a known issue with that firmware. You can request access to beta v...600 (try a PM to Susan of Diana with your DJI account email address), or wait until the next prod release which is hopefully not too far off (but who knows... ). There is a beta v...700  too, but only offered to a closed group of lucky few.

I requested v..600.  I hope it fixes it, thanks

Nelsongc1@msn.c Posted at 2018-1-16 19:11
I requested v..600.  I hope it fixes it, thanks

Could you please provide me with your DJI account email? I can add the beta to your account.

DJI Diana Posted at 2018-1-17 03:28
Could you please provide me with your DJI account email? I can add the beta to your account.

Diana,

Dji account email is

Nelsongc1@msn.com

Thanks

DJI Diana Posted at 2018-1-15 22:39
You are welcome, please keep us posted.

vs Calibration now  successful   On a windows pc    Ready to  test it. As soon as the weather improves

Nelsongc1@msn.c Posted at 2018-1-17 07:38
Diana,

Dji account email is

Got it, will add it to your account within 1 business day.

jkw Posted at 2018-1-17 16:56
vs Calibration now  successful   On a windows pc    Ready to  test it. As soon as the weather improves

Glad to hear that, hope you enjoy the drone and fly safe!

DJI Diana Posted at 2018-1-18 18:13
Got it, will add it to your account within 1 business day.

Thank you Diana

Nelsongc1@msn.c Posted at 2018-1-18 19:28
Thank you Diana

You are welcome. Added it to your account, please check it.

DJI Diana Posted at 2018-1-19 04:36
You are welcome. Added it to your account, please check it.

Diana,

Thanks for FW ..700.  Upgraded today and it flew like a dream.  Hovered and landed better than ever.  Very stable in flight and all the Intelligent flight modes worked well.  Didn't fly above 50m or farther than 200m out but seems to be good. Thanks again!

Nelsongc1@msn.c Posted at 2018-1-19 15:28
Diana,

Thanks for FW ..700.  Upgraded today and it flew like a dream.  Hovered and landed better than ever.  Very stable in flight and all the Intelligent flight modes worked well.  Didn't fly above 50m or farther than 200m out but seems to be good. Thanks again!

Glad to hear this, please feel free to let us know if you need further assistance.

I have been following this thread intently.  I am having identical problems.  After updating my iPAD PRO to the newest release, the DJI Go 4, app to v4.1.22, the aircraft to v02.00.0106, Precise Fly Safe Database to v01.00.01.07, and the Basic Fly Safe Database to v01.00.01.05, the horizontal flight is jerky.  Mind you, the gimbal seems to compensate for the jerky flight, and the horizon is level in all flight modes on mine.  But the jerky flight is VERY unnerving.  If the update to .600 or .700 has fixed the issue, I would appreciate it if I were added to the list of beta testers.  One item that was not mentioned in this thread that I can see is that when the jerky flight is happening, the blue horizon bar on the round rose on the bottom-left corner of the map display goes nuts too.

dpanetta Posted at 2018-1-21 15:51
I have been following this thread intently.  I am having identical problems.  After updating my iPAD PRO to the newest release, the DJI Go 4, app to v4.1.22, the aircraft to v02.00.0106, Precise Fly Safe Database to v01.00.01.07, and the Basic Fly Safe Database to v01.00.01.05, the horizontal flight is jerky.  Mind you, the gimbal seems to compensate for the jerky flight, and the horizon is level in all flight modes on mine.  But the jerky flight is VERY unnerving.  If the update to .600 or .700 has fixed the issue, I would appreciate it if I were added to the list of beta testers.  One item that was not mentioned in this thread that I can see is that when the jerky flight is happening, the blue horizon bar on the round rose on the bottom-left corner of the map display goes nuts too.

Pm DJI Diana, she helped me and all my problems went away.  I did download assistant 2 for the uodate.  That program allows you to reset to factory prior to the update and then reflash it.  It's also much easier to update your firmware.  I flashed it with every battery and then it also allows you to calibrate the VPS.  Once it's all updated make sure you do a IMU calibration.  I'm not sure that's all required but it works great.   Good luck.

Nelsongc1@msn.c Posted at 2018-1-21 21:20
Pm DJI Diana, she helped me and all my problems went away.  I did download assistant 2 for the uodate.  That program allows you to reset to factory prior to the update and then reflash it.  It's also much easier to update your firmware.  I flashed it with every battery and then it also allows you to calibrate the VPS.  Once it's all updated make sure you do a IMU calibration.  I'm not sure that's all required but it works great.   Good luck.

Thanks for the tips.  I have Assistant 2, and can update through it.  I have only used my IPAD in the past since it is the nearly 100% dedicated control device I use for the drone.  I just sent DJI Dana my account info.  Looking forward to making my post back on this thread that .700 fixed my issues as well