Please select Into the mobile phone version | Continue to access the computer ver.
Inspire1 Firmware v1.2.1.0 - Upgrade
1081 6 2015-4-26
Uploading and Loding Picture ...(0/1)
o(^-^)o
m.delfeld
lvl.2
Belgium
Offline

Inspire 1 Firmware v1.2.1.0 upgrade problems

On the 14th of april I have made the update of the drone and remote controls. Everything went perfectly, the update was installed perfectly in my opinion ... .. ....

I could actually fly and shoot without worry. And made several video's

This afternoon, I did a pre-flight check and find that I had no video signal on my iPad!
The app DJI signal me an update error ???? Therefore, whereas previously it was working!
After several attempts of all kinds (re-boot - dismantling - winding camera) I gave up and went back home.

Since then I try to redo the update, this is 2 hours that I try to do that damned update.

Does somebody have an idea?

2015-4-26
Use props
m.delfeld
lvl.2
Belgium
Offline

JI cried too fast for help

Searching, I finally found the problem ... ..
One of the two cables between the camera and the drone was detached from the two-'un connectors!

Dismantling the camera platform reconnection and it works!

But I find that the fixing security seem to be of. Do you know if there are replacement pieces?
2015-4-26
Use props
gmaiche
lvl.1
France
Offline

m.delfeld Posted at 2015-4-27 03:01
JI cried too fast for help

Searching, I finally found the problem ... ..

Hi m.delfeld, i have the same problem with the upgrade1,2,1.  Could you send me a picture of cable ?

Actually Dji tell me to send I1.

Here my log file. Dji tell me the line 15 is camera connexion and in my case " [00022100][15 00] device not detected."


[00010423]========== 2014.01.01 00:00:10 unsynchronized ======
[00010444]Packet [C:\WM610_FW_V01.02.01.00.bin] detected.
[00010479]Packet upgrade start...

[00010503]Packet checking...
[00010511]Done.

[00010516]Version checking[1]...
[00010521][01 00] v1.7.2499 -> v1.7.2499
[00010527][01 01] v1.7.2499 -> v1.7.2499
[00010563][03 05] v34.1.0.5 -> v34.1.0.5
[00010603][03 06] v2.0.5.10 -> v2.0.5.10
[00010614][04 00] v1.16.0.76 -> v1.16.0.76
[00010643][05 00] v2.5.6.1 -> v2.5.6.1
[00010654][08 00] v1.11.0.19 -> v1.11.0.19
[00010671][09 00] v1.7.0.3 -> v1.7.0.3
[00010703][11 00] v3.3.0.0 -> v3.2.1.0
[00010763][12 00] v1.3.0.60 -> v1.3.0.60
[00010803][12 01] v1.3.0.60 -> v1.3.0.60
[00010843][12 02] v1.3.0.60 -> v1.3.0.60
[00010883][12 03] v1.3.0.60 -> v1.3.0.60
[00022100][15 00] device not detected.
[00022143][17 00] v1.1.0.1 -> v1.1.0.1
[00022203][17 01] v2.0.0.1 -> v2.0.0.1
[00022217][19 00] v1.0.8.59 -> v1.0.8.59
[00022223]Packet upgrade failed at version checking.
2015-4-26
Use props
gmaiche
lvl.1
France
Offline

m.delfeld Posted at 2015-4-27 03:01
JI cried too fast for help

Searching, I finally found the problem ... ..

Hi m.delfeld, i have the same problem with the upgrade1,2,1.  Could you send me a picture of cable ?

Actually Dji tell me to send I1.

Here my log file. Dji tell me the line 15 is camera connexion and in my case " [00022100][15 00] device not detected."


[00010423]========== 2014.01.01 00:00:10 unsynchronized ======
[00010444]Packet [C:\WM610_FW_V01.02.01.00.bin] detected.
[00010479]Packet upgrade start...

[00010503]Packet checking...
[00010511]Done.

[00010516]Version checking[1]...
[00010521][01 00] v1.7.2499 -> v1.7.2499
[00010527][01 01] v1.7.2499 -> v1.7.2499
[00010563][03 05] v34.1.0.5 -> v34.1.0.5
[00010603][03 06] v2.0.5.10 -> v2.0.5.10
[00010614][04 00] v1.16.0.76 -> v1.16.0.76
[00010643][05 00] v2.5.6.1 -> v2.5.6.1
[00010654][08 00] v1.11.0.19 -> v1.11.0.19
[00010671][09 00] v1.7.0.3 -> v1.7.0.3
[00010703][11 00] v3.3.0.0 -> v3.2.1.0
[00010763][12 00] v1.3.0.60 -> v1.3.0.60
[00010803][12 01] v1.3.0.60 -> v1.3.0.60
[00010843][12 02] v1.3.0.60 -> v1.3.0.60
[00010883][12 03] v1.3.0.60 -> v1.3.0.60
[00022100][15 00] device not detected.
[00022143][17 00] v1.1.0.1 -> v1.1.0.1
[00022203][17 01] v2.0.0.1 -> v2.0.0.1
[00022217][19 00] v1.0.8.59 -> v1.0.8.59
[00022223]Packet upgrade failed at version checking.
2015-4-26
Use props
m.delfeld
lvl.2
Belgium
Offline

I haven't took a picture of those cable. I can tell you this was the image return cable.
From the nose os the drone it's the second cable the largest one.

When starting the drone, I got a message on the tablet "NO SIGNAL" but I could fly the drone and take pictures and video. This without seeing anything (return video I suppose) And all video's/pictures were correctly recorded.

I didn't got such messages like yours! I suppose these messages were written on the card?

After replacing the cable, I got my return video back and I could take video as before!

Anyhow, tomorrow I will get new cable at my reseller
2015-4-28
Use props
cgfelker
lvl.2
Flight distance : 83127 ft
  • >>>
United States
Offline

m.delfeld Posted at 2015-4-28 01:54
I haven't took a picture of those cable. I can tell you this was the image return cable.
From the n ...

Hi M.delfeld do you happen to have the V1.2.1.0 firmware still? I need it for a bricked inpsire I have and DJI is absolutely giving me the run around with getting it to me. They took it off the site and said they can't email it. Driving me nuts. Please help if you can.

Thank you,
Clint
2016-1-8
Use props
DJI-Ken
DJI team
Flight distance : 1515312 ft
  • >>>
United States
Offline

cgfelker@gmail. Posted at 2016-1-9 04:29
Hi M.delfeld do you happen to have the V1.2.1.0 firmware still? I need it for a bricked inpsire I  ...

Just curious how it is bricked and what 1.2 would fix.
2016-1-8
Use props
Advanced
You need to log in before you can reply Login | Register now

Credit Rules