I purchased a second Phantom 3 SE and have an issue with the gimble wandering left and right as if it was searching back and forth. Am I likly looking at a gimble problem or is it software or something else. I will attempt to attach a short video. Any advice on this would be greatly appreciated.
Thank you for responding. My firmware version is 1.9.10 and yes I just repeated the auto gimbal calibration again with no change. It has a steady approximately .5 of a second 5 to 10 degree left and right rotation.
Classic Posted at 2018-6-16 09:07
Thank you for responding. My firmware version is 1.9.10 and yes I just repeated the auto gimbal calibration again with no change. It has a steady approximately .5 of a second 5 to 10 degree left and right rotation.
Thank you for your response. If you can share with us a sample video that would be appreciated so that we can review it Thank you.
DJI Natalia Posted at 2018-6-16 10:49
Thank you for your response. If you can share with us a sample video that would be appreciated so that we can review it Thank you.
Could not directly upload but sent it to youtube and the link is here.
Also read the TF micro when trying to upgrade the firmware and the following came up.
====== 2014.01.01 00:00:12 remo-con disconnect======
[00012211]Packet: P3C_FW_V01.09.0200.bin [00012308]
[00018356]Result: Abort.
The firmware on the SD card is identical to or older than the current firmware on the aircraft.
Classic Posted at 2018-6-16 11:37
Also read the TF micro when trying to upgrade the firmware and the following came up.
====== 2014.01.01 00:00:12 remo-con disconnect======
[00012211]Packet: P3C_FW_V01.09.0200.bin [00012308]
I am following this one too. Had something similar, but when my SD card got corrupted I replace. Then had to do some upgrades, and ended up with a normal working bird.
Lonesome Crow Posted at 2018-6-16 16:17
I am following this one too. Had something similar, but when my SD card got corrupted I replace. Then had to do some upgrades, and ended up with a normal working bird.
Hey- I am tuned in and would be interested in anything you have to share.
I reformatted and attempted to install again and it aborted saying that it was already installed. I am probably way off base but I am now installing a downgrade to 1.08.10 on the chance that it might help. In your opinion does this problem appear to be a software (firmware) issue?
Just an update to inform that it still is wandering from side to side with the 1.08.10 firmware installed. I was hoping against hope on this working. I would welcome any input from anyone at this point.
Out of frustration...I did a complete format on the TF firmware card and fired it up again. This time it wanted me to upgrade from the 1.08.10 firmware to the 1.9.10 and I let it do it's thing. Camera is still twitching side to side and I am beginning to think it might have Parkensons Sorry...that is as close as I can come to humor. Surely I am not the only one out there with this situation?
Classic Posted at 2018-6-17 09:16
Out of frustration...I did a complete format on the TF firmware card and fired it up again. This time it wanted me to upgrade from the 1.08.10 firmware to the 1.9.10 and I let it do it's thing. Camera is still twitching side to side and I am beginning to think it might have Parkensons Sorry...that is as close as I can come to humor. Surely I am not the only one out there with this situation?
Sorry for the frustration. If that will be the case, I highly recommend sending the unit to our facility for a diagnosis and repair. For you to start the request you click on the link provided: http://www.dji.com/support
DJI Natalia Posted at 2018-6-18 00:06
Sorry for the frustration. If that will be the case, I highly recommend sending the unit to our facility for a diagnosis and repair. For you to start the request you click on the link provided: http://www.dji.com/support
Sorry- I am not ready to go to that expense yet and I have to think that I can't be the only one out here with the problem. Thank you in advance to anyone that can contribute.