jdmagoo Posted at 2018-10-24 01:43
Discovered another bug and report submitted.

Using the DJI 15mm lens I had the focus set to manual mode and infinity. Whilst flying around the focus automatically de-foucused, it appeared to travel from infinity to the complete opposite end of the scale and completely out of focus. This has occurred around 4-5 times over several flights using only the 15mm lens. After it occurs I can hit the infinity button and it returns back into focus. However this will have the ability to ruin the shot.

Well done, jdmagoo, please send email to the team for further investigation. Thank you.

Do you have to calibrate VPS Sensor after ?

Did it today... realy better but still unstable

Does anyone know if they will publish an updated beta firmware for us to test before this one goes public so we can confirm any of the fixes ?

FanOfFlight Posted at 2018-10-25 18:38
Does anyone know if they will publish an updated beta firmware for us to test before this one goes public so we can confirm any of the fixes ?

I hope they do, I hope they're not going to release because there hasn't been any major flight control bugs reported. Would really prefer they release beta 2 with the said bugs addressed then so on.
Perhaps one of the betas will have PRORES RAW for the X5S in there!!!

FanOfFlight Posted at 2018-10-25 18:38
Does anyone know if they will publish an updated beta firmware for us to test before this one goes public so we can confirm any of the fixes ?

Hi FanOfFlight, we are not sure about this, if there is further beta, we will share the news in the Forum.

gersphoto.orange Posted at 2018-10-26 00:45
[view_image]

Appreciate your feedback, gersphoto, please test more and report back if there is any other issue.

DJI Mindy Posted at 2018-10-26 01:00
Appreciate your feedback, gersphoto, please test more and report back if there is any other issue.

But I do not have the Remote Controller firmware version : V01.01.0050
How could I install it on my remote ?

Ok got it

gersphoto.orange Posted at 2018-10-26 02:08
Ok got it

OK, glad to know you figured it out, please let me know if you have any further concern.

Fixed a rare issue where compass interference altered the orientation of the aircraft. = checked- It's okay

  

Fixed a rare issue where the aircraft accidentally switched IMU and an incorrect landing gear status

  

prompt appeared = checked- It's okay

  

Fixed an issue where the gimbal pitch did not automatically return to center, leading to the gimbal touching the ground during landing. = checked- It's okay

  

Fixed an issue where the “Gimbal Yaw Smoothness in Follow Mode” in the DJI GO 4 app did not work.  = I still have to test

  

Fixed a rare issue when using the Zenmuse X5S where the gimbal exceeded the gimbal pan limit and drifted slightly = Is unfortunately still something with me (minimal at the drifted Lumix 14-42)

  

Fixed an issue when using Quick Spin where the aircraft did not rotate a complete 360 degrees. = I still have to test

  

I can't say exactly because we have a lot of wind at the moment, but the I2 could be even stability in the air. The P4 Pro is doing better stability right now, in the same wind. Unfortunately we have a lot of rain and strong wind at the moment, so it is difficult to fly at the moment.

Still unstable

Going back to .100, not realy good this firmware. Inspire 2 always unstable and sometime turning on himself. I had to restart the Inspire or to made a new compass calibration...

what about toilet bowl ?

auto rotate problem to

no no no... just have a look

gersphoto.orange Posted at 2018-10-26 07:03
what about toilet bowl ?

bad compass cal I would say

gersphoto.orange Posted at 2018-10-26 06:55
Going back to .100, not realy good this firmware. Inspire 2 always unstable and sometime turning on himself. I had to restart the Inspire or to made a new compass calibration...

Turning it self on sounds weird, do you have more details?

Have you reported all of this to DJI and provided them AC logs?

gersphoto.orange Posted at 2018-10-26 06:55
Going back to .100, not realy good this firmware. Inspire 2 always unstable and sometime turning on himself. I had to restart the Inspire or to made a new compass calibration...

Ok, but that hasn't happened to me yet. Only that my I2 doesn't really stand still with the beta .300 like my P4 Pro.

Yes, Inspire 2 still unstable.

gersphoto.orange Posted at 2018-10-27 02:05
no no no... just have a look
https://www.youtube.com/watch?v=QJ_pHCxu6xI&t=6s

On firm .100 is working better for you?

gersphoto.orange Posted at 2018-10-26 02:02
But I do not have the Remote Controller firmware version : V01.01.0050
How could I install it on my remote ?

This is prompted when you connect remote to aircraft, on the slave remote I did it manually by holding for a couple of secs the bar icon on the Djigo4app main screen, this opens the installation window...also works for master remote...

Nicksons Posted at 2018-10-27 14:22
On firm .100 is working better for you?

No, it was not better but not each fly

just tried the .300, noticed three major issu - stability , stability , and stability, can't live with.  the bird is not stable in the roll axe. the bird slips to the right all the time. I did a compas cal., IMU cal. and sticks cal. , but the instability still here.

Stability issues, and horizon issues on .300... fixed all kind of false warnings, like the landing or redundancy messages, all gone, camera follows ok, except for the horizon.  Signal and gps seems perfect, will go through deeper tests on next weekend in the middle of nowhere, perfect place for compass calibration, no interferences at all...

Very nice!

gersphoto.orange Posted at 2018-10-27 02:05
no no no... just have a look
https://www.youtube.com/watch?v=QJ_pHCxu6xI&t=6s

Hi gersphoto.orange, please refer to the post and email the issue to beta@dji.com with “Inspire 2 Firmware Public Beta Test Feedback” as the subject line. Thank you.

D.Raphael Posted at 2018-10-28 02:29
just tried the .300, noticed three major issu - stability , stability , and stability, can't live with.  the bird is not stable in the roll axe. the bird slips to the right all the time. I did a compas cal., IMU cal. and sticks cal. , but the instability still here.

Hi D.Raphael, thanks for your feedback, please try more open places to see if the issue persists, if yes, please refer to the post and email the issue to beta@dji.com with “Inspire 2 Firmware Public Beta Test Feedback” as the subject line. Thank you.

DJI Mindy Posted at 2018-10-29 00:05
Hi gersphoto.orange, please refer to the post and email the issue to  with “Inspire 2 Firmware Public Beta Test Feedback” as the subject line. Thank you.

That with gersphoto.orange is not a firmware beta .300 problem. I talked to him about it in the Facebook group and he has the same problem with version .100 and also with .200. I think this is a hardware error with the compass.

AeroMovie Posted at 2018-10-29 00:33
That with gersphoto.orange is not a firmware beta .300 problem. I talked to him about it in the Facebook group and he has the same problem with version .100 and also with .200. I think this is a hardware error with the compass.

AeroMovie, thanks for letting us know, it could be the hardware related, if the issue persists in every place and every firmware, it is recommended to send in for evaluation.

DJI Mindy Posted at 2018-10-29 01:11
AeroMovie, thanks for letting us know, it could be the hardware related, if the issue persists in every place and every firmware, it is recommended to send in for evaluation.

yes Mindy, I had also suggested that he send his I2 to DJI for testing. But it's his decision what he does.

DJI Mindy Posted at 2018-10-29 01:11
AeroMovie, thanks for letting us know, it could be the hardware related, if the issue persists in every place and every firmware, it is recommended to send in for evaluation.

My bird came back from your technical service since july 2018. There is a big problem with stability for this one and the other one before.

gersphoto.orange Posted at 2018-10-29 02:39
My bird came back from your technical service since july 2018. There is a big problem with stability for this one and the other one before.

Sorry to hear that, I recommend to report the issue to beta@dji.com first to see if you could get any response from our engineers.

AeroMovie Posted at 2018-10-29 01:49
yes Mindy, I had also suggested that he send his I2 to DJI for testing. But it's his decision what he does.

Thanks for your suggestion, we will follow up his issue, please do more tests of the beta to see if there is any further issue.

Going to try again and again new compas calibration

Just send me an #Inspire2 and I'll test anything you want me to, all day every day

Point is that I've spent 10K on mine so don't really want to be testing anything apart from how to get my shot with a "professional" drone..

DJI Mindy Posted at 2018-10-29 00:07
Hi D.Raphael, thanks for your feedback, please try more open places to see if the issue persists, if yes, please refer to the post and email the issue to  with “Inspire 2 Firmware Public Beta Test Feedback” as the subject line. Thank you.

Hi Mindy, thanks for your response. I tried several times at different places , with the same result . i will report back to the Beta.

D.Raphael Posted at 2018-10-29 20:16
Hi Mindy, thanks for your response. I tried several times at different places , with the same result . i will report back to the Beta.

Thank you, the team will handle it.