Hi ,

if you want to use the ronin S with the old Dji Focus or power your camera you will want to use the two 12V/2A can ports. I read in some other thread
that the pin out is 1:+12V , 2:-12V so it seams easy and straight forward to make your own cable. I my case I wanted a can bus to d-tap so I can power
the old Dji Focus and the Blackmagic Pocket 4k camera.

So I ordered this Dji cable : https://store.dji.com/de/product ... or-ronin-mx-srw-60g and cut it in half to get the can bus plugs and I ordered
a female d-tap plug https://www.amazon.com/Vellcon-R ... ywords=d-tap+female . Total cost about 20€ for two canbus to d-tap cables.

So this is what´s gonna save you some time as you can´t know which pin is represented by what cable:
red is 12V+ , blue and gray/white are for data - and then there are a bunch of unshielded blank cables you should all twist togeather for your 12V- !

hope this works for you and saves some time

can bus cable

almost finished

finished can to d-tap

Awesome just what I was looking for!

dopey-tree Posted at 12-15 08:32
Awesome just what I was looking for!

;) I was already wondering if I was the only one looking to do this ....

Flo the Pirate Posted at 12-15 12:22
;) I was already wondering if I was the only one looking to do this ....

Heyy, I bet you are not!  I am trying to do the same with the ronin s to power the bmpcc4k and the tilta nucleos motor
Was wondering if your setup is running fine!
Hope to hear from you, thanks in advance

AllAirStep Posted at 12-18 13:32
Heyy, I bet you are not!  I am trying to do the same with the ronin s to power the bmpcc4k and the tilta nucleos motor
Was wondering if your setup is running fine!
Hope to hear from you, thanks in advance

All works fine ... if you run into problems powering from one can bus try to take power from the second - I ran into this problem with a teradek

AllAirStep Posted at 12-18 13:32
Heyy, I bet you are not!  I am trying to do the same with the ronin s to power the bmpcc4k and the tilta nucleos motor
Was wondering if your setup is running fine!
Hope to hear from you, thanks in advance

Hello
excuse my English
I'd like to feed the pocket 4k, do you have any idea as far as it could feed ronin s and pocket?

I think this cable should work too, a bit cheaper and you don't have to cut and throw away a connector .. It's meant for the MX but as far as I understood, can bus connection are the same as the S
Ronin-MX RSS power cable :

I modified this long ago for Tilta Nucleus M, may help you

fans1ae40bcc Posted at 1-14 01:16
I think this cable should work too, a bit cheaper and you don't have to cut and throw away a connector .. It's meant for the MX but as far as I understood, can bus connection are the same as the S
Ronin-MX RSS power cable :
[view_image]

this should work as well ! But u don´t have to throw away a connector ... just make two units for those two power outlets .... at one point you will need them eg focus motor or teradek ..

Kwan Posted at 1-14 14:13
I modified this long ago for Tilta Nucleus M, may help you

https://www.youtube.com/watch?v=EWu6WPumV4s

sweet setup !

Kwan Posted at 1-14 14:13
I modified this long ago for Tilta Nucleus M, may help you

https://www.youtube.com/watch?v=EWu6WPumV4s

sweet setup !

Kwan Posted at 1-14 14:13
I modified this long ago for Tilta Nucleus M, may help you

https://www.youtube.com/watch?v=EWu6WPumV4s

Hey, can you make a more detailed video on how you made the 7pin to Ronin/S cable?