Please select Into the mobile phone version | Continue to access the computer ver.
DJI FPV Remote Controller Roll and Yaw issues
376 12 3-26 09:00
Uploading and Loding Picture ...(0/1)
o(^-^)o
Ayuuzawa
lvl.1

Australia
Offline

Just received my DJI FPV Mode 2 Combo earlier today.

I've encountered an issue with the RC when either Yaw or Roll is moved to their maximum positions. On both the Windows 10 Controller interface and Liftoff simulator, the position of the sticks will show at maximum momentarily before suddenly appearing at their minimum values. This is all happening whilst I am holding the sticks to their maximums.

The issue is able to be reproduced consistently if I move either stick to the bottom right positions. It will show the yaw or roll values increasing before suddenly dropping to minimum once maximum is reached.


Is there a fix for this issue?


3-26 09:00
Use props
Tom_A
Captain
Flight distance : 589623 ft
  • >>>
United States
Offline

I have seen this too, but it only happens when connected to a computer and using a simulator. I’m not sure if this is something that needs to be fixed in the remote or in the simulators.
3-26 09:47
Use props
Ayuuzawa
lvl.1

Australia
Offline

Tom_A Posted at 3-26 09:47
I have seen this too, but it only happens when connected to a computer and using a simulator. I’m not sure if this is something that needs to be fixed in the remote or in the simulators.

I'm not able to test the RC on a quad yet, but if this is true then it's relieving to know that the quad won't be suddenly flipping on me during flight.
3-26 10:08
Use props
Tom_A
Captain
Flight distance : 589623 ft
  • >>>
United States
Offline

Ayuuzawa Posted at 3-26 10:08
I'm not able to test the RC on a quad yet, but if this is true then it's relieving to know that the quad won't be suddenly flipping on me during flight.

I didn’t notice this issue on mine immediately. When I did notice it, I hooked a quad up to Betaflight and tested to be sure it was not happening when really flying.
3-26 10:15
Use props
schl0r
lvl.3

Germany
Offline

same for me. I was about to send my controller back when I realised that the issue does not exist in Betaflight. You will not have this issue in real flight. Only in Sim.
You can mitigate by recalibrate the controller through the goggles.

3-26 13:49
Use props
Ayuuzawa
lvl.1

Australia
Offline

schl0r Posted at 3-26 13:49
same for me. I was about to send my controller back when I realised that the issue does not exist in Betaflight. You will not have this issue in real flight. Only in Sim.
You can mitigate by recalibrate the controller through the goggles.

Thanks, looks like I'll have to test it in betaflight first thing when I get the chance.
3-26 14:37
Use props
schl0r
lvl.3

Germany
Offline

the problem is Windows, I reckon.
When you calibrate the controller in Windows, you can check the checkbox for 'raw input'. You'll see that Windows thinks that after 128 follows minus 127.
3-27 01:04
Use props
DJI Thor
Administrator
Flight distance : 13602 ft
Offline

You may try to calibrate the controller after connecting to the simulator. If the actual flight is normal, there is no issue with the controller, please don't worry.
3-28 01:00
Use props
djiuser_oqivBPIo3gNE
New

Italy
Offline

I just received the fpv combo too. I have just use the remote linked to the PC and the simulator. It's normal that as soon as turn on the remote there is a fan quite noisy? I mean very noisy
3-30 14:47
Use props
Ayuuzawa
lvl.1

Australia
Offline

schl0r Posted at 3-27 01:04
the problem is Windows, I reckon.
When you calibrate the controller in Windows, you can check the checkbox for 'raw input'. You'll see that Windows thinks that after 128 follows minus 127.

Yea, seems to be the case. If I remember correctly on the Taranis I had there were options to limit channel output to 127 so this wouldn't happen.

But again, if it doesn't happen in betaflight then there isn't a major issue.
3-30 15:02
Use props
Ayuuzawa
lvl.1

Australia
Offline

djiuser_oqivBPIo3gNE Posted at 3-30 14:47
I just received the fpv combo too. I have just use the remote linked to the PC and the simulator. It's normal that as soon as turn on the remote there is a fan quite noisy? I mean very noisy

I experienced the same. The fan in the controller seems to be quite loud, but I think it's normal.
3-30 15:03
Use props
tags_fpv
lvl.1
Canada
Offline

I have the same issue.  But for me it is the throttle. when I have the throttle all the way down, it goes into MAX throttle mode on my simulator.  Does anyone have a fix for this?
3-31 11:41
Use props
DJI Thor
Administrator
Flight distance : 13602 ft
Offline

Hi all, an update for the issue, we will fix it in a future firmware update.
4-23 01:55
Use props
Advanced
You need to log in before you can reply Login | Register now

Credit Rules