Trying automated treatment with the granule spreader and it is limiting treatment height to 32.8 feet (10 m).  We'd like to use the automated system and be spreading between 100-300 ft. (30-90 m).  Anyone know how to set the system to allow automated spraying at higher altitude?  

It allows us to manually start the spreader at 100 ft (30 m)

The height limit of MG-1P is 30m by default, when the Altitude Stabilization function of rader module is enabled, it could achieve terrain following capatibilities, the drone could continuously climb up to 80m along with the terrain.

DJI Mindy Posted at 4-5 01:14
The height limit of MG-1P is 30m by default, when the Altitude Stabilization function of rader module is enabled, it could achieve terrain following capatibilities, the drone could continuously climb up to 80m along with the terrain.

Where in the settings can I increase the treatment height? Currently only allow 10m height when doing an automated spray mission.

For clarification: We are using the MG Spreading system (granules), When we create a field and enter the speed, height it only allows for a maximum height of 10m.  How to we change this to allow us to treat at 30m?  Please provide us with step by step procedure or any resources that are available.  Thanks!

For clarification: We are using the MG Spreading system (granules), When we create a field and enter the speed, height it only allows for a maximum height of 10m.  How to we change this to allow us to treat at 30m?  Please provide us with step by step procedure or any resources that are available.  Thanks!

For clarification: We are using the MG Spreading system (granules), When we create a field and enter the speed, height it only allows for a maximum height of 10m.  How to we change this to allow us to treat at 30m?  Please provide us with step by step procedure or any resources that are available.  Thanks!

FC Mosquito Posted at 4-5 15:09
Where in the settings can I increase the treatment height? Currently only allow 10m height when doing an automated spray mission.

For clarification: We are using the MG Spreading system (granules), When we create a field and enter the speed, height it only allows for a maximum height of 10m.  How to we change this to allow us to treat at 30m?  Please provide us with step by step procedure or any resources that are available.  Thanks!

Update:  We have been successful in getting our Agras to make treatments at 70ft (all the higher we can get it to go).  We did the following. Create spray block with handheld, turn off Radar Height and then execute the mission.  Once the drone takes off and is on it's way to the sprayblock use the stick to fly up to desired height.  This may not be the best way but the only way we have figured out so far.  Support from DJI is not good.

I am buying a fly control for agras mg-1p. Should I send the damaged serial number flight?

DJI Mindy Posted at 4-5 01:14
The height limit of MG-1P is 30m by default, when the Altitude Stabilization function of rader module is enabled, it could achieve terrain following capatibilities, the drone could continuously climb up to 80m along with the terrain.

Is there a firmware version that can increase the height limitation?

automodality Posted at 2020-10-23 12:11
Is there a firmware version that can increase the height limitation?

There is.  If you contact DJI they can create a custom "patch" to address your spray setting needs.  We were able to get DJI to do this and it allows us a new height limitation.  

FC Mosquito Posted at 3-16 06:15
There is.  If you contact DJI they can create a custom "patch" to address your spray setting needs.  We were able to get DJI to do this and it allows us a new height limitation.

We are having the same problem trying to apply BTI, G/FG etc. Do you have any contact information for DJI to request patch/firmware? Your time is greatly appreciated. Thanks!

fans7eeceb82 Posted at 3-18 11:16
We are having the same problem trying to apply BTI, G/FG etc. Do you have any contact information for DJI to request patch/firmware? Your time is greatly appreciated. Thanks!

Yes we do, unfortunately our UAV Pilot, Andrew is on vacation until next week.  He can share the contact information with you if you want to reach out to him.  
asage@fcmcd.org or call (509) 545-4083