Hi guys,
I decided to collect all the Mavic Mini errors and give recommendations what you can do in your case.
** Code 10001: Camera malfunction. Repairs required. Contact DJI Support for assistance - All you can do is restart the drone. If it doesn’t help, replace or repair the Gimbal camera.
** Code 10016: Camera not calibrated. Image quality can be affected. Contact DJI Support for assistance. - Calibrate the camera, if the error persists - replace or repair the camera.
** Code 10022: No SD card. Insert sd card - Just insert or replace the card.
** Code 10023: SD card malfunction. Change card - Try pulling and inserting back. It did not help - change the SD card.
** Code 30007 & 30008: No GPS signal. Unable to hover. Fly with caution - Repair or replacement of the gps module is required.
** Code 30047: Barometer initialization failed. Restart aircraft - Follow the instructions of the DJI.
** Code 30049: GPS Module Error. Restart Aircraft - Restart the mavic mini. If it does not help, repair or replace the gps module.
** Code 30050: IMU calibration required. Calibrate IMU - In the settings, find the IMU calibration function and calibrate according to the instructions. If it does not help, repair or replace the gps module.
** Code 30055: IMU not calibrated. Calibrate IMU - Repeat the same steps as with the Code 30050 error.
** Code 30060: Compass error. Ensure there are no metal or magnetic objects near the aircraft and calibrate it before use. - If there are definitely no metal objects around mavic mini and calibration does not help - repair or replace the gps module.
** Code 30064: Unable to TakeOff. - Make sure that nothing prevents the drone from taking off and that you are in the area where flights are allowed. If all conditions are met, but the error remains - restart mavic mini. Doesn't help - update the firmware. If again the error - need repair mavic mini ( but here it is need to understand which module is broken, the fastest is the problem in ESC module).
** Code 30168: Aircraft power insufficient. Fly with caution. - The error most often occurs in high winds, but it can be due to a worn battery or a faulty ESC module.
** Code 30210: Power system hardware. Restart aircraft - Reboot helps. If not, update the firmware.
** Code 30226: Start failed. Restart aircraft and DJI Fly App - Follow the instructions of the DJI.
** Code 40002: Gimbal stuck. Check whether gimbal cover is removed and ensure gimbal can rotate freely - Be careful. You can burn the suspension motors, if you forget to remove the cover.
** Code 40011: Gimbal calibration error. Restart aircraft. - Calibrate the gimbal in the settings. If calibration does not work, replace the gimbal.
** Code 40012: Gimbal unable to connect. Repairs required. Contact DJI Support for assistance. - Need to replace the gimbal. Watch the video how to do it.
** Code 40021: Gimbal IMU data error. Contact DJI Support for assistance - Repair or replace GPS module. Watch the video how to do it.
** Code 180016, 180031, 180030: sensor error. Contact DJI Support for assistance. - Try restarting the drone. If it does not help, the sensors are broken and must be replaced.
Often errors occur due to a software failure and these problems can be solved by updating the firmware. Unfortunately, many errors can be caused due to a hardware problems of the module. But don't worry, you can always fix everything.
In video below, I'll show you how to disassemble the Dji Mavic Mini to replace any of the broken parts.
** If the Mavic Mini does not turn on and does not show signs of life, you should pay attention to the main board. Time code 5:50
** Dji Mavic Mini loses GPS signal or Code 30002 error appears indicating a weak GPS signal and unstable positioning, maybe the problem is in the GPS module. Time Code 6:39
** Camera with suspension stabilization - Gimbal. The most fragile part of the quadrocopter, it falls out when drone drop in 99% cases, but fortunately it is easily installed back into place in the quadrocopter. In 70% drop cases - Gimbal may crack or break the cable connecting the camera and the main board, this cable can be removed and replaced. Replacing the camera and cable - Time code 7:07
** ESC errors cause unstable operation of the motors or even loss of quadrocopter control, because the ESC board is responsible for controlling all four motors. Replacing the ESC / IMU board may be necessary if the Mavic Mini reports an ESC error that is NOT resolved by replacing the quadcopter motor (note that you may need to replace the motor again, as sometimes the original damaged ESC board may damage the new motor) - Time code 8:10
** Motor error or replacement hand with the motor - Time code 8:32
To replace the motor you need a soldering-iron. A motor error may be caused due to defective of the ESC board.
Everything written above is based only on my experience. If you have experience repairing the Mavic Mini please share it.
About the ribbon connectors: there's usually two blobs of hot glue on either side of them. There's a high chance of snapping them off you don't warm up the glue.
About another error that I've seen happening: no GPS, somehow related to battery fault or bad connection, to be investigated (I've seen this posted by two different users).
Another code to add to your list, 30085, is an error code having to do with ESC communication. When you have this error,the motors won't do their little vibration and start up, and won't make that little dji tone either.
In my case it was a problem with the ribbon cable connecting the main and ESC boards. Main connectors simply needed to be under a tad bit of pressure ( see end of my thread ). But I'm sure this can range to broken ribbon cables as well.
Very helpful. Getting power system hardware error 30210. Never crashed. Worked great last time I used it a few month ago. Have reset aircraft numerous times. Will try firmware update.
jz729 Posted at 4-7 02:58
Another code to add to your list, 30085, is an error code having to do with ESC communication. When you have this error,the motors won't do their little vibration and start up, and won't make that little dji tone either.
In my case it was a problem with the ribbon cable connecting the main and ESC boards. Main connectors simply needed to be under a tad bit of pressure ( see end of my thread ). But I'm sure this can range to broken ribbon cables as well.
hello my mavic mini in the first flight take off in the water , and now i have error 30085 for esc board , what can i do?
I'm getting error 40021 after replacing the gimbal. Do you know how to fix this? Or is it absolutely necessary to replace the GPS module with the gimbal..?
DenizS Posted at 7-5 12:00
hello friends, I have error code called 30142 (Unable to rotate) anyone have seen that code before)?
Just purchased a Mavic Mini today and got the error code 30142 the first time I tried to fly it right out of the box - very first time. The one motor that won’t rotate seems to be a bit stiffer to rotate by hand but will turn with a bit more resistance. Super disappointed and can’t believe a brand new unit won’t fly. Can’t find anything about this error code online besides this post. Returning it to the retailer tomorrow hoping it will be replaced as a defective unit. Any other tips on what this is would be much appreciated.
Error codes are nice but what if the error is before the system can do a selfcheck?
In my case the mini doesn´t seem to boot properly. Only the 1st and the 4th LEDs are shining and no gimbal check is performed after motor check. Has anyone an idea what does it mean when only the both outer leds are shining?
I was able to get the app loaded (iPhone 11) and controller bound to the UAV, but the camera wasn't working. I had to take my phone out of the case to get the plug in all the way. I don't want to have to do this every time I use the UAV, so I switched to my iPhone 5s. The app loaded and was able to show it was bound to the remote. The camera still wasn't connected (none of the telemetry was showing either (height, speed, etc) but it was showing in another portion of the app I did have flights and the length of time (just a min for each). So,,,, anybody have any ideas what might be the issue with the camera? The app said here was an "error code 01, to restart" the UAV, which I did with no luck. I am able to use the roller pad to tilt the camera but there is no transmission from the camera to the app.
djiuser_pOhMfaNux55Q Posted at 5-21 03:40
Same Problem here with DJI Smart Controller and Mavic Air. Both on newest firmware with DJI Assitant 2. No solutions after two days of Heavy trys.
Code: 3000003 and sometimes Code 30226
Account not logged in. Flight altitude and distance restricted to nnn and nnn. Check and log in (Code: 3000003)
Restart aircraft and DJI Fly (Code: 30226)
I have a newly purchased dji Mavic mini 2. after 20 minutes of flight it shows error Code "30226: Start failed. Restart aircraft and DJI Fly App
- Follow the instructions of the DJI." So far nothing helped. Does anyone have an idea what the Error code actually stands for? DJI tells me to return it but i am far out in the african bush with no access to any store.
djiuser_zWY1IfDUoM52 Posted at 5-25 19:47
I have a newly purchased dji Mavic mini 2. after 20 minutes of flight it shows error Code "30226: Start failed. Restart aircraft and DJI Fly App
- Follow the instructions of the DJI." So far nothing helped. Does anyone have an idea what the Error code actually stands for? DJI tells me to return it but i am far out in the african bush with no access to any store.
Post #30 tells you what code 30226 means - Restart aircraft and DJI Fly app - have you tried this?
djiuser_NPerGy1tvEGH Posted at 5-28 17:02
Just got him with my new Mavic Mini(1). Straight out of the box, I got these three codes: 180016, 180030, 180031.
Looks like I’ll have to send it away for repairs, and wait who knows how long, before I even fly it. Pretty disappointed.
Have no image on my mavic mini, codes
Vision sensor error 180030;
Vision sensor error 180031;
Downward vision sensor error 180016;
Now questinon for million dollars...
Whether there is a possibility that these errors occur due to damage to the video signal cable and if it does not visually appear to be damaged
Hi, will esc problem make the battery info undetectable?
my mavic mini can power on, but with error 30064 and i found that no battery info, all the calibrate no problem
lvl.2
Second Officer
Captain
lvl.3
lvl.4
lvl.1
New
