Anyone heard anything about this .36 version that's mentioned in the .700 SC update, seems 1 or 2 have it but not the majority

Thought for a minute that DJI forgot it at start and included it later. So, tried to reinstall the same firmware version ... no succes to get the 4.3.36.
Trying to upgrade thru the app itself ... "you got the latest" as result.

The DJI website still shows the 4.3.32, so does the Google play store.

Have you tried updating thru the Assistant?

Visual Air Posted at 4-28 16:25
Have you tried updating thru the Assistant?

I only update thru the DJI Assistent.

I always update through assistant2

Im guessing the newer versions have the very annoying altitude and line of sight popup messages?
If so, stick to a less obtrusive older version.

At first, the firmware updated itself via WIFI, but version .32 remained... I reset the SC to the factory settings and and reinstalled the new firmware via DJI Assistant, and then, version .36 appeared.

Dronie2 Posted at 4-30 00:34
At first, the firmware updated itself via WIFI, but version .32 remained... I reset the SC to the factory settings and and reinstalled the new firmware via DJI Assistant, and then, version .36 appeared.

well, I reinstalled the version thru DJI Assistent 2, 3 times already. Still on .32
I have never updated via WiFi.

JohnDG Posted at 4-30 01:27
well, I reinstalled the version thru DJI Assistent 2, 3 times already. Still on .32
I have never updated via WiFi.

Have you reset the SC to the factory settings and installed the new firmware? Or just reinstalled it...?

Go4 .36 is software not firmware.  Different things.
If you really want .36 Go4 then try the update in the Go4 menu or just download the APK and install manually.

Dronie2 Posted at 4-30 01:42
Have you reset the SC to the factory settings and installed the new firmware? Or just reinstalled it...?

Just reinstalled it, this time.

I did a factory reset when installing the former update in early march. Wondering it's a new procedure that one have to reset to factory every new firmware update.

gnirtS Posted at 4-30 04:09
Go4 .36 is software not firmware.  Different things.
If you really want .36 Go4 then try the update in the Go4 menu or just download the APK and install manually.

Go 4 .36 is included in the last firmware. You can update the App (software) manually but NOW, it is updated with this version of firmware.

Perhaps, someone can have a problem with the update, but I have updated everything at the same time.

found the .36 version, it was in the download folder, just didn't install by itself, all good now.

Are the uncloseable annoying popups from the norma versions for altitude and BLOS present on .36 still?

don't know yet, winds been crap for months and now rain added to the mix, so not flown in a while

successfully upgraded to .700 SC and Go 4 .36 without  glitch,  all done thought Wi-Fi connected SC itself.

Ditto as earlier comments that highlight new type of warning message popping out whenever the altitude reaches 120m even there is no altitude restriction at the area where my drone take off.
Silently and steadily, DJI introducing excessive restrictions or let say "army barrack rules"  which don't really like at all.

You can downgrade to the older version by downloading the APK if needed.  No more nag messages.

They've screwed up here, a once off message per flight for height or distance is fine *provided you can close it*.
DJI have no idea what clearances you have, what mountain or valley you're standing in and so on - the distracting message interferes with flight constantly making an incident more likely.  Or at best, a complete pain in the arse.

had a fly today and the nagging is there, but with the feelworld monitor I have attached to the SC nothing is on there but the camera view so lucky there.