After the new firmware update even with 21 sats this thing keeps saying atti mode or if my signal gets low it pops up as well. Dji please fix these issues!

I have the same issue right now with my mini 2 and even 28 satellites. After every flight mode switch ( c/n/s ) it says „ATTI mode“. RTH is still working.

lnnrtwlk Posted at 1-5 07:41
I have the same issue right now with my mini 2 and even 28 satellites. After every flight mode switch ( c/n/s ) it says „ATTI mode“. RTH is still working.

Same thing. My rth works still as well. It’s just annoying and should not be happening

lnnrtwlk Posted at 1-5 07:41
I have the same issue right now with my mini 2 and even 28 satellites. After every flight mode switch ( c/n/s ) it says „ATTI mode“. RTH is still working.

Is it possible to make a screen-recording of a flight in wich ATTI is seen?

If RTH works than ATTI seen on the screen  is not a real ATTI !

cheers
JJB

JJB* Posted at 1-5 07:55
Is it possible to make a screen-recording of a flight in wich ATTI is seen?

If RTH works than ATTI seen on the screen  is not a real ATTI !

Im pretty sure that ATTI is not activated but it keeps confusing me and it‘s a little bit annoying

I started with the same issue after the last app update. https://forum.dji.com/forum.php? ... d=232173#pid2380475

ohhhhhhh

I think i will hold off updating to latest firmware than ....

Yeah my next flight if it starts acting up again will try to catch a recording of it by screen recording

Here’s my flight, RTH works but Atti warnings

The issue is with iOS if I use Android everything is fine but if I use my iPhone 11 or iPad mini 4 I keep getting the atti mode warning even though I have 25+ satellites.

I have android. Never experienced it so defo on iOS

Lots of reports on Mavic Pilots forum also, so where are the DJI moderators on this?

It’s does not matter what system it’s on it should be looked into and fixed. This has to be a big a fly today with no issues but yesterday it was acting up again

Same thing here...did update on new Mini 2 before first flight, immediately started getting ATTI mode warnings with over 20 satellites.

magna99 Posted at 1-8 09:27
Same thing here...did update on new Mini 2 before first flight, immediately started getting ATTI mode warnings with over 20 satellites.

It's not the firmware. It happened to me on both my mini 2 and original mini 1. Using IOS 14.3 and dji fly 1.2.2

bob_r@reagan.com Posted at 1-8 10:15
It's not the firmware. It happened to me on both my mini 2 and original mini 1. Using IOS 14.3 and dji fly 1.2.2

I didn’t have this issue until DJI Fly 1.2.2 so I agree I don’t believe it is aircraft FW.  What I’d like to know is where are the DJI moderators on this issue? They are commenting on every trivial (no offence to forum contributors) yet ignoring a very real issue.

TDZHDTV Posted at 1-8 11:39
I didn’t have this issue until DJI Fly 1.2.2 so I agree I don’t believe it is aircraft FW.  What I’d like to know is where are the DJI moderators on this issue? They are commenting on every trivial (no offence to forum contributors) yet ignoring a very real issue.

The forum moderators are here to look after the forum, not to solve your problems. They will tell you, as I am, to raise this issue directly with DJI Support. Alternatively, other forum members may be able to help you.

Updated my Mini 2 to the latest firmware.
Unlike ever befor I get ATTI mode warnings most of the time when initiating a flight. When I click on the warning it usually initiates the « homepoint updated » notification and all is fine after. Something needs to be addressed here DJI.

Geebax Posted at 1-8 14:00
The forum moderators are here to look after the forum, not to solve your problems. They will tell you, as I am, to raise this issue directly with DJI Support. Alternatively, other forum members may be able to help you.

Hi, I see moderators passing information onto the technical teams all the time, I’m frustrated because I’ve seen no such response.

Same issue here - flying today on iOS, I got several ATTI mode warnings, but had strong signal.

Flight logs do not show a loss of GPS signal, so it looks like an app problem.

Same " Attitude" warning messages for me. The bigger problem is when I hit the RTH button my drone flew back, started to lower then gained altitude, flew sideways.  I cancelled RTH and had to force land it.
Glad I was in an open area. As of yesterday I spoke with DJI and had to open a Cas Number. From reading all the different posts, it looks like others have contacted DJI about these issues. Hope they can correct issues soon.

Had a similar problem.

It is NOT just IOS I had this issue the other day on my One Plus 8 Pro (Android) I had over 25 satellites complete open air and it said GPS signal weak for a brief moment, This software or this drone cannot be trusted at the moment, If it does not switch back to GPS mode and you are high up with wind say goodbye to your M2.

I've so far have only had the "ATTI Mode" notification issue twice on back to back flights, using the up to date firmware and DJIFly app on an iPhone 11 Pro.  Was a rather hot day (38°C) and a little bit of wind but had 15-23 GPS satellites. The aircraft still operated normally, not acting if it was in ATTI Mode and would RTH.

Last flight didn't get the warnings, only thing that changed was I had rebooted the app before the flight, temperature that day was about 32°C.

I'm having the same issue after updating to the latest Aircraft firmware 01.02.0100. I'm also running RC firmware 02.00.1200 and iOS app v 1.2.2. I live in the Southwestern United States with perfectly clear skies, but lately I keep getting the ATTI mode alert and a loss of GPS signal despite seeing up to 21 satellites. I cannot not hover to save my life but RTH does continue to work. I see from all the other posts I'm not alone in this situation. Hoping for a solution.

I had this same issue yesterday, right after updating.  I thought it was the cold temps, but it's the update.  They will fix it inthe next one I'm sure.

51 Drones Posted at 2-13 04:33
I had this same issue yesterday, right after updating.  I thought it was the cold temps, but it's the update.  They will fix it inthe next one I'm sure.

Well there have been multiple posts on this issue and not one moderate has responded or even advised that the information has been passed onto the technical team, so I wouldn’t hold your breath.