Hi All,

Anybody facing this error. imu calibration incomplete code 30084 and 30056. IMU calibration will fail at 2%.
Its happen after servicing gimbal and change gimbal cable.

list of action taken
1) Swap IMU wth other mini 3 set. Not ok.
2) Replaced IMU with other mini. OK
3) Update/downgrade firmware still not ok.

Hello there Reza mavicmini. I am sorry to know that you are receiving these error messages on your DJI Mavic Mini and thank you for reaching out. Kindly please try to restart the said DJI drone and recalibrate the IMU multiple times, if the error persists, you may need to contact our DJI Support Team at https://www.dji.com/support and send the drone for service and repair. Again I am sorry for the trouble and thank you.

DJI Stephen Posted at 12-6 02:43
Hello there Reza mavicmini. I am sorry to know that you are receiving these error messages on your DJI Mavic Mini and thank you for reaching out. Kindly please try to restart the said DJI drone and recalibrate the IMU multiple times, if the error persists, you may need to contact our DJI Support Team at https://www.dji.com/support and send the drone for service and repair. Again I am sorry for the trouble and thank you.

I've calibrate it for almost 2 month..nothing happened

Sounds a bit like it might be time to send it in to a DJI service center for diagnostic testing.  

DowntownRDB Posted at 12-6 13:20
Sounds a bit like it might be time to send it in to a DJI service center for diagnostic testing.

gonna cpst me alot .. thanks anyway

Reza mavicmini Posted at 12-6 16:01
gonna cpst me alot .. thanks anyway

Unfortunately you are right about the cost.  Wish your DIY fix would have worked out without issue.  

Reza mavicmini Posted at 12-6 05:52
I've calibrate it for almost 2 month..nothing happened

Hello, there. Sorry for your inconvenience. May we confirm that have you created a repair case? For the error codes, we would suggest you try to reboot the aircraft and recalibrate IMU. If the issue persists, we would recommend you send it back. Here is the link: https://www.dji.com/service/repair?from=store_footer

Reza mavicmini Posted at 12-6 05:52
I've calibrate it for almost 2 month..nothing happened

Hi there Reza mavicmini. Thank you for the reply and for the given update. Since after the calibration the issue still persist. It would be best to contact our DJI Support Team at https://www.dji.com/support for us to be able to assist you further. Thank you.

DJI Stephen Posted at 12-8 20:56
Hi there Reza mavicmini. Thank you for the reply and for the given update. Since after the calibration the issue still persist. It would be best to contact our DJI Support Team at https://www.dji.com/support for us to be able to assist you further. Thank you.

thanks sir..really aprreciiate it

DJI Stephen Posted at 12-8 20:56
Hi there Reza mavicmini. Thank you for the reply and for the given update. Since after the calibration the issue still persist. It would be best to contact our DJI Support Team at https://www.dji.com/support for us to be able to assist you further. Thank you.

with many thanks..

Hey Reza did you ever resolve your issue. I am facing the exact same problem. Please guide me how did you fit the errors 30055 and 30056

umair air2s Posted at 9-14 21:06
Hey Reza did you ever resolve your issue. I am facing the exact same problem. Please guide me how did you fit the errors 30055 and 30056

Hi sorry for the late reply. For this issues it comes from the mainboard problem. I have send my unit to 3rd party technician. It was caused by the intermittent which was on the gimbal cable camera slot port.  They need to modify it to rectify the problem. Other options is you need to replace the mainboard. Sorry man.. thats the only solution

"I have send my unit to 3rd party technician. It was caused by the intermittent which was on the gimbal cable camera slot port." Can you please elaborate this a little further, I feel that you have missed something there????? please and many thanks for replying.

umair air2s Posted at 9-15 05:43
"I have send my unit to 3rd party technician. It was caused by the intermittent which was on the gimbal cable camera slot port." Can you please elaborate this a little further, I feel that you have missed something there????? please and many thanks for replying.

base on my my experience , it was cause by mainboard problem. you need to replaced the mainboard.

or otherwise you need to find someone who can refurbished the mainboard

Reza mavicmini Posted at 9-15 05:53
base on my my experience , it was cause by mainboard problem. you need to replaced the mainboard.

or otherwise you need to find someone who can refurbished the mainboard

Hi , can u tell me how to refurbish the main board?

Thank you for the reply I guess you are pointing in the right direction but I fail to understand that how can IMU error be related to main board.

I have a Drone mavic Air 2. One of the motors stopped while it was at the top. After it fell, I tried to start it, but the motherboard did not respond. I replaced the motherboard. Several errors appeared. I dealt with all of them except error 30084 for the ESC. I could not fix it... What should I do? Are there special programs?

DJI Stephen Posted at 2021-12-6 02:43
Hello there Reza mavicmini. I am sorry to know that you are receiving these error messages on your DJI Mavic Mini and thank you for reaching out. Kindly please try to restart the said DJI drone and recalibrate the IMU multiple times, if the error persists, you may need to contact our DJI Support Team at https://www.dji.com/support and send the drone for service and repair. Again I am sorry for the trouble and thank you.

I have a Drone mavic Air 2. One of the motors stopped while it was at the top. After it fell, I tried to start it, but the motherboard did not respond. I replaced the motherboard. Several errors appeared. I dealt with all of them except error 30084 for the ESC. I could not fix it... What should I do? Are there special programs?

djiuser_7tGeeu3k5M09 Posted at 10-16 02:07
I have a Drone mavic Air 2. One of the motors stopped while it was at the top. After it fell, I tried to start it, but the motherboard did not respond. I replaced the motherboard. Several errors appeared. I dealt with all of them except error 30084 for the ESC. I could not fix it... What should I do? Are there special programs?

Hello there. Sorry about the inconvenience. You can submit a repair request using this link: https://repair.dji.com/. You can also use the following link to check for the nearest authorized service center in your location: https://www.dji.com/service/repair/centers. Have a nice day ahead.