Overview:

• Release Date: 2022.03.23
• Remote Controller Firmware: v03.01.0600
• DJI Fly App: v1.5.10
  

What’s New?

• Fixed some bugs for remote controller
  

Notes:

• This version contains important updates. It is recommended to update the remote controller.
• If the update fails, restart DJI RC Pro, and use DJI Fly or DJI Assistant 2 (Consumer Drones Series) to retry.
  

thank you  for the update...

Thanks for the update.  Just FYI the Assistant still shows a February release date, but the version is correct.

dr6583 Posted at 3-22 21:13
Thanks for the update.  Just FYI the Assistant still shows a February release date, but the version is correct.

Maybe they finished it in February but didn't release it until the software for the M3 was fully tested...

Thanks for updating.  

Its this a dji joke? I just try this new update in my air 2s and menu camera in the rc pro its a mess i cant change from camera to video and some of the camera options are not responding. Nothing new and something worst. eooooooooo dji
edit

I have rebooted and now everything seems to respond. I don't know what caused the error because I had already restarted after updating

no problems here working 100% on Air2s and Mavic 3.

On the next update, please add the shutter speed and aperture change possibilities on the 5D button (left-right and up-down). It is missing from the RC Pro.

Thanks for the update. Working fine with my Air2s

Hi. My new RC Pro arrived today, but I can't pair it with my Air 2S

ReproRetro Posted at 3-30 02:42
Hi. My new RC Pro arrived today, but I can't pair it with my Air 2S

Oh no!  Did you try the manual process of holding the battery button for 4 seconds until it beeps?

ReproRetro Posted at 3-30 02:42
Hi. My new RC Pro arrived today, but I can't pair it with my Air 2S

is the rc pro updated to the last firmware?

dr6583 Posted at 3-30 07:14
Oh no!  Did you try the manual process of holding the battery button for 4 seconds until it beeps?

Thanks for that. It worked eventually.
I had charged but devices and updated the firmware on both with DJI Assistant. Then rebooted both and entered paring mode on both. But they just wouldn't connect.
After 4 times I gave up, came back later to try 'just for the hell of it' and this time it worked - go figure

juanpirulo Posted at 3-30 14:04
is the rc pro updated to the last firmware?

Thanks for that. It worked eventually.
I had charged but devices and updated the firmware on both with DJI Assistant. Then rebooted both and entered paring mode on both. But they just wouldn't connect.
After 4 times I gave up, came back later to try 'just for the hell of it' and this time it worked - go figure

Hi, i'm one problem, after upgrade firmware NO connected with Mavic 3 and Air 2s. I don't know what is the happened. I have tried to subtract the DJI RC Pro but it always stays with version 03.01.0600. What could be going on? Can I do a factory firmware reset? Thank you!

Apologies, I will re-explain my case. The RC Pro when I first connected it to the Mavic 3 worked with many cuts. Then I linked it again and it worked. So far so good. Then it asked me for the last firmware update and I could never link it to the Mavic 3 again, let alone the Air 2s (I had already done the upgrade). When it connects it gives me a message that there is a firmware inconsistency, it tries to upgrade, and then it says "connect it again after the RC Pro does the reset", but it doesn't do it. I try to reboot the computer but I can't connect to any of the aircraft (neither the Mavic 3 nor the Air 2s.  How can I reset the device to an initial factory firmware other than v03.01.0600? Thanks again!

GLSpro60 Posted at 3-30 23:45
Apologies, I will re-explain my case. The RC Pro when I first connected it to the Mavic 3 worked with many cuts. Then I linked it again and it worked. So far so good. Then it asked me for the last firmware update and I could never link it to the Mavic 3 again, let alone the Air 2s (I had already done the upgrade). When it connects it gives me a message that there is a firmware inconsistency, it tries to upgrade, and then it says "connect it again after the RC Pro does the reset", but it doesn't do it. I try to reboot the computer but I can't connect to any of the aircraft (neither the Mavic 3 nor the Air 2s.  How can I reset the device to an initial factory firmware other than v03.01.0600? Thanks again!

Tray to refresh firmware of the rc pro with mavic assistant 2 (consumer drone series). cheers

juanpirulo Posted at 3-31 01:12
Tray to refresh firmware of the rc pro with mavic assistant 2 (consumer drone series). cheers

Thanks. Yes, i try, but still no linking...I don't know. Too reset de RC but nothing. I will try again! Thanks.

GLSpro60 Posted at 3-30 23:45
Apologies, I will re-explain my case. The RC Pro when I first connected it to the Mavic 3 worked with many cuts. Then I linked it again and it worked. So far so good. Then it asked me for the last firmware update and I could never link it to the Mavic 3 again, let alone the Air 2s (I had already done the upgrade). When it connects it gives me a message that there is a firmware inconsistency, it tries to upgrade, and then it says "connect it again after the RC Pro does the reset", but it doesn't do it. I try to reboot the computer but I can't connect to any of the aircraft (neither the Mavic 3 nor the Air 2s.  How can I reset the device to an initial factory firmware other than v03.01.0600? Thanks again!

I had the exact same scenario with the A2S initially.  It says firmware mismatch, then downloads a small piece of software to the controller, then it says the RCP will restart but never does.  Just restart it manually, and possibly the A2S as well.  For me, it resolved the issue.

Does this firmware update address the problem of the Mavic 3 being "disconnected from RC" even when extremely nearby (i.e. inside 50 meters?) I've had this problem countless times in a variety of locations including while just sitting at my DESK.

DJI Support has told me to update the firmware (which I have) to see if it fixes the problem. But it's not listed in the notes about what this firmware update is supposed to fix.

Are you planning on adding Mavic Air 2 compatibility to the RC?

Please add the capability to swap places the wheel button for camera gimbal and zoom. This is a huge problem for left handed people  Thx

thank you for the update

Basically I got a pretty good zoom lens but I want a
static tripod shot where the camera zooms out of the
subject but found that using the focus motor and wheel
is very jittery, is there a way to program it to zoom at a
steady rate?

djiuser_qbqsYSV7ssRu Posted at 4-19 13:47
Basically I got a pretty good zoom lens but I want a
static tripod shot where the camera zooms out of the
subject but found that using the focus motor and wheel

It’s not letting me create a new thread so I’ll ask here

djiuser_qbqsYSV7ssRu Posted at 4-19 13:48
It’s not letting me create a new thread so I’ll ask here

You might need to post a couple more times to get to 20 points to be able to create a thread

When are you going to make this compatible with Mavic 2 Pro

Please how to download the firmware