Overview:

• Date: 2023.1.6
• DJI O3 Air Unit Firmware: V01.02.0000
• DJI FPV Goggles V2 Firmware: V01.06.0000
• DJI Goggles 2 Firmware: V01.04.0000
• Remote Controller Firmware: V02.00.0500
  

What's New?

• Added support for the DJI O3 Air Unit to record video at 4K@30fps, 2.7K@30fps, and 1080p@30fps. When used with DJI Goggles 2, 4K@120fps, 2.7K@120fps, and 1080p@120fps are also supported.
• Added ability to set the sharpness and noise reduction value. Go to Settings  Camera  Advanced Camera Settings in the goggles menu to set the value.
• The time for DJI O3 Air Unit to enter low-power state after stopping the aircraft motors has been changed from three seconds to six seconds.
• Improved D-Cinelike to 10bit, providing more possibilities for post-processing.
• Optimized the camera exposure in some backlighting scenarios to avoid over-dark in shadow areas.
• Optimized the remote controller signal in some scenarios.
  

Notes:

• Restart DJI O3 Air Unit, the remote controller, and goggles after the update is complete.
• If update fails, restart DJI O3 Air Unit and DJI Assistant 2 (Consumer Drones Series), then try again.
  

---

Overview:

• Date: 2022.11.22
• DJI O3 Air Unit Firmware: V01.01.0000
• DJI FPV Goggles V2 Firmware: V01.04.0000
• DJI Goggles 2 Firmware: V01.02.0000
• Remote Controller Firmware: V02.00.0300
  

What's New?

• Added the following video recording specification:
• With DJI FPV Goggles V2: 4K@120fps, 4K@100fps
• With DJI Goggles 2: 4K@100fps
• Added the function to use DJI Assistant 2 (Consumer Drones Series) to update the camera calibration file to guarantee image quality after the camera module is replaced.
• Optimized the power consumption strategy in low-power state to improve the stand-by time.
  

Notes:

• Restart the aircraft, remote controller, and goggles after the update is complete.
• If update fails, restart DJI O3 Air Unit and DJI Assistant 2 (Consumer Drones Series), then try again.
  

TUTORIAL HERE:

https://forum.dji.com/forum.php? ... D767%26typeid%3D767

I dont understand why a google would limit fps, the older one can 4K@120fps? But the recording is done on the module, not the goggles.

Only thing i would think is that the goggles2 cant do 120fps in the goggles, but rather have a few frame skipping then losing 20fps.  

When will you bring comaptibility for Goggles 2 with the Vistas and older AirUnits ??

djiuser_UoAO0SPIDgoU Posted at 11-24 20:29
When will you bring comaptibility for Goggles 2 with the Vistas and older AirUnits ??

I've been wondering the same thing. hope its sooner than later

djiuser_UoAO0SPIDgoU Posted at 11-24 20:29
When will you bring comaptibility for Goggles 2 with the Vistas and older AirUnits ??

Very soon!!

When will they do away with the rc loss with video loss? NEVER had that issue with the black fpv remote. Anyway the black one can be adapted to O3 au? Or at least adapt the Grey rc to the old vista's but let it use dedicated 2.4ghz? So no loss of rc when video loss.  Very frustrating considering I have over 23 vista units and I don't want to have to buy rx for every one. I'd use my gray rc except if it's going to lose link during vid loss...that's a big no deal...

Missing advance gimbal setting for mini3pro, anyone can help?

Does this update kills the FCC hack?

When will INAV be supported ?

Ricardo Cerqueira Posted at 11-30 06:24
Does this update kills the FCC hack?

I think it does (See Mads Tech @MadRC video on YT). This would be VERY bad and prevents me from buying the O3 unit until this is cleared up.

I just learned: Betaflight will be changing the font in 4.4
Why did DJI not implement MSP Displayport like all other competitors ?? So O3 OSD will be fucked in 4.4

Please work with the INAV developers to implement OSD - if you can make it work for Betaflight I'm SURE you can get it to play nice with INAV
Caroline

Will there be a update to use dji fpv controller 2 with the old dji air unit and caddx vistas?

Tell me about DJI o3 and DJI rcpro fpv live.
How I can use it ?
Avata works , but DJI o3 not.
Can you add DJI o3 to DJI fly (and transmisjom to fpv live)

is it possible to get the beta firmware I like to connect my air units to my goggle 2

willempost Posted at 12-7 09:26
is it possible to get the beta firmware I like to connect my air units to my goggle 2

That firmware is now live.

fichek Posted at 12-8 06:15
That firmware is now live.

Ok thanks
Can not try it anymore I have sended my goggles 2 back because it was closing my nose
I could not use it without breathing trought my mouth very uncomfortable
Really Bad design

Tadango Posted at 2022-12-2 04:00
I think it does (See Mads Tech @MadRC video on YT). This would be VERY bad and prevents me from buying the O3 unit until this is cleared up.

where is that video? cant find it, hehe

Great update thanks dji

With this update what is the goggles 2 live view frames when recording at 120? Is it 100 still?

Can we get an update for the V2 Goggles?
I would like to connect all of my googles to the updated Vista?!

Jacektfc Posted at 2022-12-4 14:18
Tell me about DJI o3 and DJI rcpro fpv live.
How I can use it ?
Avata works , but DJI o3 not.

It is working since the update with v2 goggles

jan_S Posted at 2022-12-2 06:13
I just learned: Betaflight will be changing the font in 4.4
Why did DJI not implement MSP Displayport like all other competitors ?? So O3 OSD will be fucked in 4.4

I'm using Betaflight 4.4 and it's working fine in my Goggles 2. However, I must say, it works fine as long as I don't switch to HD for the OSD. If I switch to HD, it pushes everything off the screen to the right. I've tried to adjust it by moving everything in Betaflight to the left, but it still does not work well. So I'm just keeping my OSD on NTSC for now. Hopefully, DJI will fix that issue in the future.

FPVTrendz Posted at 1-8 09:18
I'm using Betaflight 4.4 and it's working fine in my Goggles 2. However, I must say, it works fine as long as I don't switch to HD for the OSD. If I switch to HD, it pushes everything off the screen to the right. I've tried to adjust it by moving everything in Betaflight to the left, but it still does not work well. So I'm just keeping my OSD on NTSC for now. Hopefully, DJI will fix that issue in the future.

The HD OSD is not yet finished for DJI.

Tadango Posted at 2022-12-2 04:00
I think it does (See Mads Tech @MadRC video on YT). This would be VERY bad and prevents me from buying the O3 unit until this is cleared up.

There is nothing in that video about it... What part are you referring to?

FPV gogles V2 with 1.06 FW can work with VISTA v1.00 FW ? Not using DJI controller.

Me pregunto si algún día harán compatible el air unit o3 con la emisora fpv 1?
Es lamentable que cada vez que venden algo nuevo todo lo antiguo queda inutilizado... alguien sabe algo al respecto?

CappyA330 Posted at 1-8 09:33
I think it is a BetaFlight 4.4 release candidate iissue, not a DJI issue. The HD OSD is not yet finished for DJI. Hopefully with the final release of 4.4 it will be fixed.

That's good to know because I would love to use the HD OSD, so here's hoping it's Betaflight and it get's fixed

O3 Has no HD OSD support yet, it is not a BF issue...

Is it possible for Dji developers to find some way to connect the Dji O3 air unit to the mini 2 controllers.  Or make an app for iOS and android that makes it possible to fly dji aircrafts. ..

Anyone have issues with the goggles 2 power input having a short? I'm trying to power up a new set and theres something getting really hot inside the goggle under touchpad area and nothing is turnibg on. Even the connector for the battery cable is getting hot but this same power cable works fine with another set of goggles 2. I can also smell a slight burnt smell coming from the goggle near the power input so definitely not trying to power it up again.

Hi, at this day, we must always rebind when switch vista to o3 with  goggles V2 ?

fansb8724559 Posted at 2-14 18:12
Anyone have issues with the goggles 2 power input having a short? I'm trying to power up a new set and theres something getting really hot inside the goggle under touchpad area and nothing is turnibg on. Even the connector for the battery cable is getting hot but this same power cable works fine with another set of goggles 2. I can also smell a slight burnt smell coming from the goggle near the power input so definitely not trying to power it up again.

The strong heating inside the goggles occurs when using a non-original battery with a voltage that differs from the standard (9V). If a similar problem occurs with an original battery, it is a reason to contact the manufacturer

fansb8724559 Posted at 2-14 18:12
Anyone have issues with the goggles 2 power input having a short? I'm trying to power up a new set and theres something getting really hot inside the goggle under touchpad area and nothing is turnibg on. Even the connector for the battery cable is getting hot but this same power cable works fine with another set of goggles 2. I can also smell a slight burnt smell coming from the goggle near the power input so definitely not trying to power it up again.

must be an issue with the goggles internally. also i know the goggles 2 cant support any battery with the XT60 connector, like i know 6S deff doesnt work. It might be 2S only, im not sure.

oh the 4.4 bricked my flight controller lol thought was just me, reciever binds but isnt recognized