Please select Into the mobile phone version | Continue to access the computer ver.
User Guide for FAA Remote ID Compliance
20522 34 2023-3-18
Uploading and Loding Picture ...(0/1)
o(^-^)o
DJI Support
Administrator
Flight distance : 2408 ft
Hong Kong
Offline

Table of Contents

2      Frequently Asked Questions

2023-3-18
Use props
DJI Support
Administrator
Flight distance : 2408 ft
Hong Kong
Offline

1        Purpose

As drones became more common, governments around the world have developed rules to encourage safe and productive drone flights while protecting airplanes and helicopters in the air as well as people and property on the ground. Now, a big part of the new era of drone regulation is about to take effect in the United States: Remote Identification (Remote ID).

Remote ID creates a common and consistent way for authorities to monitor airborne drones and identify who is flying them. Similar to a car license plate, this new method of aerial accountability will make the skies safer, improve public acceptance of drones, and open up new possibilities for drone pilots to routinely fly in ways that have until now been restricted for safety and security reasons – like flying at night or directly over people.

The FAA’s first Remote ID compliance deadline, for newly manufactured drones that require registration with the FAA, is September 16, 2022, though the FAA announced an extension to enforce it until December 16, 2022. Customers who already own DJI drones should comply with the FAA's Remote ID regulations on the second compliance deadline which has been extended to March 16, 2024. DJI continues to provide firmware updates to bring most modern DJI drones into compliance. Customers can install those updates at their discretion any time before March 16, 2024. We hope this simple guide to the FAA’s Remote ID rules will help answer any questions you have.

FAA Remote ID Compliance Deadlines:
  • First compliance deadline (for manufacturers): extended to December 16, 2022
  • Second compliance deadline (for operator or pilot): extended to March 16, 2024



2023-3-18
Use props
DJI Support
Administrator
Flight distance : 2408 ft
Hong Kong
Offline

2        Frequently Asked Questions
2.1     What is FAA Remote ID?

The FAA Remote ID rule requires most drones operating in US airspace to have Remote ID capability. Think of Remote ID as an electronic license plate system for drones, allowing authorities to identify who is flying them. A physical license plate wouldn’t be much use on a small airborne drone, so Remote ID sends license plate information via radio signals to receivers on the ground. Remote ID will provide information about drones in flight, such as the identity, location, and altitude of the drone and its control station.
2023-3-18
Use props
DJI Support
Administrator
Flight distance : 2408 ft
Hong Kong
Offline

2.2        Which drone pilots must comply with the rule and when?
Drone pilots which have been registered or are required to be registered, including those flown for recreation, business, or public safety, must comply with the rule on Remote ID beginning with the second compliance deadline.
2023-3-18
Use props
DJI Support
Administrator
Flight distance : 2408 ft
Hong Kong
Offline

2.3         Do I have to upgrade to the RID-compliant firmware that has been released that supports FAA Remote ID functionality?
DJI advises customers to comply with Remote ID rule as soon as possible. On and after the second compliance deadline, all drone pilots which have been registered or are required to register must operate their drone in accordance with the FAA Remote ID rule. This means that you may need to upgrade the RID-compliant firmware unless your drone is not required to be registered and is unregistered.
2023-3-18
Use props
DJI Support
Administrator
Flight distance : 2408 ft
Hong Kong
Offline

2.4        If I upgrade RID-compliant firmware, can I manually disable Remote ID?
No. According to the Remote ID rule, the Remote ID system cannot be disabled.
2023-3-18
Use props
DJI Support
Administrator
Flight distance : 2408 ft
Hong Kong
Offline

2.5        What are the ways for drone pilots to comply with the Remote ID rule?
There are three ways drone pilots can meet the identification requirements of the Remote ID rule:

  • Operate a Standard Remote ID drone that broadcasts identification and location information of the drone and control station. A standard remote ID drone is one that is produced with built-in Remote ID broadcast capabilities. All new drones produced by DJI now that weigh more than 250 grams have these capabilities. Some drones made before the first compliance deadline may have these capabilities by upgrading the RID-compliant firmware as well.

  • Operate a drone with a Remote ID broadcast module giving the drone's identification, location, and take-off information. A broadcast module is a device that can be attached to a drone. Persons operating a drone with a Remote ID broadcast module must be able to see their drone at all times during flight. All DJI drones that were made before the first compliance deadline but without RID-compliant firmware due to hardware and software limitations could comply with the Remote ID rule through an additional Remote ID Broadcast Module.

  • Operate (without Remote ID equipment) at FAA-recognized identification areas (FRIAs) sponsored by community-based organizations or schools. FRIAs are the only locations unmanned aircraft (drones and radio-controlled airplanes) may operate without broadcasting Remote ID message elements.





2023-3-18
Use props
DJI Support
Administrator
Flight distance : 2408 ft
Hong Kong
Offline

2.6        Which DJI drone models support FAA Remote ID?
You can check the list of drone models approved by the FAA by visiting this webpage.

2023-3-18
Use props
DJI Support
Administrator
Flight distance : 2408 ft
Hong Kong
Offline

2.7        What actions do I need to take if I want to comply with the Remote ID rule by upgrading RID-compliance firmware?
You may need to take the following three actions.

Action 1: Upgrade RID-compliant FirmwareThe RID-compliant firmware released by DJI meets the compliance requirements of Standard Remote ID. To meet the requirements of the FAA Remote ID rule, both the drone firmware and the DJI flight control app need to be upgraded. The following operation must be followed as well:
  • If you are a user of a DJI remote controller without an integrated GNSS system, such as DJI RC-N1, RC-N2, you need to connect an external device with an integrated GNSS system such as a cell phone or tablet as a location source to it, and must run the DJI flight control app such as DJI Fly in the foreground and always allow the DJI flight control app to obtain its location information.
  • If you are a user of a DJI remote controller without an integrated GNSS system, such as DJI Motion Controller and DJI FPV Remote Controller 2, and wearing a DJI Goggles without an integrated GNSS system, you need to upgrade the firmware of the DJI Goggles, connect the above external device as a location source to the DJI Goggles, run the DJI flight control app such as DJI Fly in the foreground and always allow the DJI flight control app to obtain its location information.
  • If you are a user of a DJI remote controller with an integrated GNSS system, such as DJI RC, RC 2, RC Pro, RC Plus or DJI Smart Controller and DJI Goggles Integra, you need to upgrade these remote controllers and Goggles to the latest firmware without connecting an additional device as a location source.

Action 2: Add drone Remote ID information on the FAA Drone Registration System
Under the Remote ID rule, the Certificate of Aircraft Registration of the drone used in the operation must include the Remote ID serial number of the drone. Each applicant for a Certificate of Aircraft Registration must submit the following required information to the Registry:
  • Drone manufacturer and model name
  • Remote ID serial number

There are two ways to register a drone in the United States:

The following guide takes the online registration of drone at FAA DroneZone as an example. The registration of DJI agricultural drone may require the operator to register by mail. For detailed requirements, please visit the FAA website.


When you choose "ADD DEVICE" in "Inventory" on the FAA DroneZone webpage, the following window will pop up, asking you to enter the Remote ID related information.

1.jpg

Below we guide you on how to fill in the required information.
DOES YOUR DRONE BROADCAST FAA REMOTE ID INFORMATION?
If you have completed the above Action 1 and confirmed that the Remote ID functionality is working properly Note [1], you can select "YES"
DEVICE TYPE
Select “Standard Remote ID”
UAS MANUFACTURER
Enter “DJI”
UAS MODEL
Particular “MODEL” can be found on the approved DOC published by the FAA, as shown “Mavic 3 Pro” below:
1.png


REMOTE ID SERIAL NUMBER
If the drone has a 20-digit alphanumeric serial number (always prefixed with 1581F)
In this case, the Remote ID serial number is the same as the aircraft serial number, and generally the same as the flight controller serial number, for example: Mavic 3 series, Mini 3 series, Avata, Matrice 30 series, Mavic 3 Enterprise series, etc. You can check the serial number of the drone in various ways:
  • Serial number on the box sticker Note [2]
  • Serial number inside battery compartment or elsewhere on the fuselage of the drone Note [2]
  • Serial number inside the DJI flight control app
  • Serial number inside “Available networks” of the WLAN Note [3]

Note [1] See 2.8 below - "How to check if the Remote ID functionality is working properly?"
Note [2] Visit DJI service webpage for more information:
Note [3] See Way 3 in 2.8 below - "How to check if the Remote ID functionality is working properly?"

If the drone has a 14-digit alphanumeric serial number
In this case, the Remote ID serial number is not the same as the aircraft serial number (or flight controller serial number), for example: DJI Phantom Pro V2.0, Phantom 4 RTK, Mavic 2 series, Mavic Air 2, Air 2S, FPV, Matrice 300 RTK, Agras T30, etc. You can get the Remote ID serial number of these drone in the following two ways:
  • Remote ID Serial number inside the DJI flight control app such as DJI GO 4, DJI Fly, DJI Pilot, DJI GS RTK and DJI Agras to name a few.

      The following images show the Remote ID serial number on DJI GO 4, DJI Pilot, DJI GS RTK, DJI Fly and DJI Agras using DJI Phantom 4 Pro V2.0, Mavic 2 Pro, Phantom 4 RTK, Air 2S and T30 as examples respectively.
1.png
Phantom 4 Pro V2.0 (DJI GO 4)

2.png
Mavic 2 Pro (DJI GO 4)

3.png
Phantom 4 RTK (DJI Pilot)

4.png
Phantom 4 RTK (DJI GS RTK)

5.png
Air 2S (DJI Fly)

6.png
T30 (DJI Agras)



  • Remote ID Serial number inside “Available networks” of the WLAN Note [3]
Note [3] See Way 3 in 2.8 below - "How to check if the Remote ID functionality is working properly?"

After filling in the required information, as shown in the image below (take Air 2S as an example), click "ADD DEVICE".
5.jpg


Action 3: Affix a RID compliance label to your drone
Under the FAA Remote ID rule, drones with Standard Remote ID capabilities are required to have a RID compliance label affixed to indicate that the drone complies with the Remote ID rule. Newly produced drone with compliant Remote ID capabilities will have RID compliance identifier before being put on market. For drone have been upgraded with RID-compliant firmware but do not have a RID compliance identifier affixed, you should label your drone with “ASTM F3411-22a-RID-B” and this label must be legible, prominent and permanently affixed to the drone.
7.png





2023-3-18
Use props
DJI Support
Administrator
Flight distance : 2408 ft
Hong Kong
Offline

2.8        How to check if the Remote ID functionality is working properly?
There are several ways to check if Remote ID is working properly.
Way 1: Remote ID status display on the DJI flight control app
Way 2: Remote ID status display on the DJI Goggles
Way 3: Remote ID serial number displayed in “Available networks” of the WLAN

Way 1: Remote ID status display on the DJI flight control app

The drone automatically initiates a pre-flight self-test (PFST) of the Remote ID system before takeoff, and cannot take off if it does not pass the PFST. The results of the PFST of the Remote ID system, i.e. the working status, can be viewed in the DJI flight control apps below.
DJI Fly
If the Remote ID is working properly, you can see “Remote ID functionality normal”, as shown in the following image.
2.82.jpg


If the Remote ID is working abnormally, DJI Fly will display "Remote ID error", as shown in the following image.

2.83.jpg


DJI Pilot 2
If the Remote ID is working properly, the RID icon in the upper left corner of the DJI Pilot 2 homepage will be displayed in BLACK, and DJI Pilot 2 will display “Normal” on the Camera View, as shown in the Figure below.
DJI Pilot 2 homepage
2.84.jpg


Camera View

2.85.jpg

If the Remote ID is working abnormally, the RID icon in the upper left corner of the DJI Pilot 2 homepage will be displayed in RED, and DJI Pilot 2 will display “Remote ID module error” on the Camera View, as shown in the image below.

DJI Pilot 2 homepage

2.86.jpg


Camera View
2.87.jpg
DJI Agras
If the Remote ID is working properly, the RID “Normal” status will be displayed on the Aircraft Information page of the DJI Agras app, and there is no display of any RID abnormal status in the Camera View, as shown in the Figure below.
Aircraft Information Page
2.88.jpg


Camera View

2.89.jpg


If the Remote ID is working abnormally, the RID “Error” status will be displayed on the Aircraft Information page of the DJI Agras app, and “Remote ID module error” will be displayed on the Camera View as well, as shown in the Figure below.
Aircraft Information Page
2.810.jpg


Camera View
2.811.jpg

DJI GO 4
If the Remote ID is working properly, you can see “Remote ID functionality normal”, as shown in the following image.
8.png

DJI Pilot
If the Remote ID is working properly, DJI Pilot will display Remote ID Status “Normal”, as shown in the following image.
9.png

DJI GS RTK
If the Remote ID is working properly, DJI GS RTK will display Remote ID Status “OK” on Aircraft module self-check page, as shown in the following image.
10.png


Way 2: Remote ID status display on the DJI Goggles
If the Remote ID is working properly, the Status bar in the upper left corner of the DJI Goggles will display “Remote ID functionality normal”, as shown in the Figure below.
2.812.jpg


If the Remote ID is working abnormally, "Remote ID error" will be displayed in the lower right corner of the DJI Goggles.
2.813.jpg

Way 3: Remote ID serial number displayed in “Available networks” of the WLAN
Use the DJI remote controller to control the drone to start the motors, then use the WLAN of your cell phone or tablet to scan the Remote ID serial number broadcast by the drone at a location close to the drone Note [4]. As shown in the image below, if you can see a string always prefixed with “RID-” followed by a 20-digit alphanumeric Remote ID serial number in the "Available networks", it means that the Remote ID is broadcast properly.
2.814.jpg
Note [4] Since the time required for WLAN scanning of different cell phones or tablets is not consistent, it may be necessary to restart the WLAN several times to scan the Remote ID serial number broadcast by the drone.






2023-3-18
Use props
DJI Support
Administrator
Flight distance : 2408 ft
Hong Kong
Offline

2.9        I bought a new drone, how to check whether the drone has built-in compliant Remote ID functionality?
Newly produced drones with compliant Remote ID capabilities will have RID compliance identifier before being put on market. In any case, it is recommended that you check whether the drone is RID compliant by any of the following ways.
Way 1: Check whether there is a RID compliance identifier “ASTM F3411-22a-RID-B” on the box of the drone
Way 2: Check whether a RID compliance identifier “ASTM F3411-22a-RID-B” is on the drone compliance label

RID compliance identifier on box
The RID compliance identifier is usually printed on a sticker with the drone serial number or on a sticker with compliance information, as shown in the image below.
2.815.png


RID compliance identifiers on drone airframe
RID compliance identifier is usually combined with other compliance identifiers such as FCC ID, IC and CMIIT, which are directly lasered on the airframe or printed on stickers affixed to the airframe. The image below takes the combined compliance label of M300 RTK as an example.
2.9.png



2023-3-18
Use props
DJI Support
Administrator
Flight distance : 2408 ft
Hong Kong
Offline

2.10        I bought a drone with built-in RID compliance functionality, what actions do I need to take?
Unlike drone users who have firmware upgrades to comply with the Remote ID rule, you may not need to specifically upgrade the RID compliant firmware and affix the RID compliance identifier to the drone airframe, as the drone is inherently RID-compliant and has the RID compliance identifier affixed. You may simply need to correctly fill in the Remote ID related information when registering the drone, see Action 2 in the 2.7.
2023-3-18
Use props
DJI Support
Administrator
Flight distance : 2408 ft
Hong Kong
Offline

2.11        My drone cannot comply with the Remote ID rule by upgrading firmware, what should I do?
On and after the second compliance deadline, if you continue to fly the drone, you will have to comply with the rule in either of the two ways described below.
  • Operate a drone with a Remote ID broadcast module giving the drone's identification, location, and take-off information. A broadcast module is a stand-alone device that can be attached to a drone, and a visit to the FAA web page will provide information on broadcast modules that have been approved by the FAA. Persons operating a drone with a Remote ID broadcast module must be able to see their drone at all times during flight.
  • Operate (without Remote ID equipment) at FAA-recognized identification areas (FRIAs) sponsored by community-based organizations or schools. FRIAs are the only locations unmanned aircraft (drones and radio-controlled airplanes) may operate without broadcasting Remote ID message elements.


2023-3-18
Use props
DJI Support
Administrator
Flight distance : 2408 ft
Hong Kong
Offline

2.12        I decided to comply with rule by adding a Remote ID module to the drone, what should I be aware of?
The Remote ID module you purchase must be FAA-approved. Follow the Remote ID module instruction manual to properly install it on the drone and make sure the module will not affect the safe operation of the drone. You also need to add Remote ID module information such as make, model, and serial number to the FAA drone registry.


2023-3-18
Use props
DJI Support
Administrator
Flight distance : 2408 ft
Hong Kong
Offline

2.13        What are the conditions for a drone to start broadcasting Remote ID signals?
The drone will start broadcasting the FAA Remote ID signal when all of the following conditions are met.
  • The drone has built-in Remote ID functionality.
  • The drone is within airspace of the United States.
  • The drone is in flight (i.e. the propellers are turning).



2023-3-18
Use props
DJI Support
Administrator
Flight distance : 2408 ft
Hong Kong
Offline

2.14        Does the drone with built-in Remote ID still broadcast FAA Remote ID signals when flying outside the US?
No
2023-3-18
Use props
DJI Support
Administrator
Flight distance : 2408 ft
Hong Kong
Offline

2.15        If I bring a drone with built-in Remote ID to the US from a non-US country, will the drone broadcast FAA Remote ID signals when flying in the US?
Yes

2023-3-18
Use props
DJI Support
Administrator
Flight distance : 2408 ft
Hong Kong
Offline

2.16        Will Remote ID reduce battery life?
No
2023-3-18
Use props
DJI Support
Administrator
Flight distance : 2408 ft
Hong Kong
Offline

2.17 How do DJI Mini series users comply with the Remote ID rule?
As per the FAA Remote ID rule, all drone pilots required to register their UAS must operate their aircraft in accordance with the final rule on and after the second compliance deadline. According to FAA requirements, drones that weigh 0.55 pounds or less (less than 250 grams), and are flown under the Exception for Limited Recreational Operations, do not need to be registered. Therefore, if you are operating a drone with a take-off weight of 0.55 pounds or less (less than 250 grams) for purely recreational purposes, you may not need to register your drone and comply with the Remote ID rule. Please visit the FAA's official website for requirements related to drone registration and Remote ID. Here are additional notes on the Remote ID functionality for the DJI Mini series.
  • DJI Mini 4 Pro & Mini 3: These aircraft support the FAA Remote ID functionality. However, for the latest aircraft firmware (v01.00.03.00 for Mini 4 Pro and v01.00.04.10 for Mini 3), the Remote ID will only be activated when the Intelligent Flight Battery Plus is used.
  • DJI Mini 3 Pro: The aircraft supports the FAA Remote ID functionality regardless of whether an Intelligent Flight Battery Plus or Intelligent Flight Battery is used.
  • DJI Mini series (e.g. Mini & Mini SE) and DJI Mini 2 series (e.g. Mini 2 & Mini 2 SE): These aircraft have a nominal take-off weight of less than 249 grams (including a battery, propellers and a MicroSD card), and does not support FAA Remote ID functionality.








2023-3-18
Use props
DJI Support
Administrator
Flight distance : 2408 ft
Hong Kong
Offline

2.18        I am a DJI Avata user, how do I comply with Remote ID rule?
Read Answer for Question 2.7, then watch the instructional video.
11.png
2023-3-18
Use props
DJI Support
Administrator
Flight distance : 2408 ft
Hong Kong
Offline

2.19        What will happen if the built-in Remote ID of the drone malfunctions or fails during flight?
The drone monitors the Remote ID system functionality from pre-flight to shutdown. If the Remote ID system malfunctions or has a failure, an alarm will be displayed in the DJI flight control app or DJI Goggles or third-party apps developed based on the latest DJI Mobile SDK that supports Remote ID. As required by the rule, the person manipulating the flight controls of the drone must land it as soon as practicable if the drone is no longer broadcasting Remote ID signals.
2023-3-18
Use props
DJI Support
Administrator
Flight distance : 2408 ft
Hong Kong
Offline

2.20        Do I have to connect to a wireless or Wi-Fi network for the Remote ID functionality to work properly?
No, but connecting to the network is convenient to speed up the time to get the location of the remote controller required by the Remote ID rule.
2023-3-18
Use props
DJI Support
Administrator
Flight distance : 2408 ft
Hong Kong
Offline

2.21        What should I do if I'm using a third-party app based on the DJI Mobile SDK to control the DJI drone?
After you upgrade the RID-compliant firmware, you must use an app developed based on the DJI Mobile SDK that supports the FAA Remote ID to control your drone, otherwise the drone will not be able to take off.

Before the second compliance deadline, if the app developed based on the DJI Mobile SDK that supports the Remote ID is not yet available, you may use the DJI flight control app to manipulate the drone to take off, and then manually switch to the third-party app developed by DJI Mobile SDK. However, please note that on and after the second compliance deadline, you must use an FAA RID-compliant DJI flight control app or an app based on the DJI Mobile SDK that supports the Remote ID to manipulate your drone during the entire flight from takeoff to landing.

DJI provides developers with the DJI Mobile SDK that supports the FAA Remote ID functionality, for detailed APIs information, please visit https://developer.dji.com/mobile-sdk/


2023-3-18
Use props
DJI Support
Administrator
Flight distance : 2408 ft
Hong Kong
Offline

2.22        Where can I see more detailed Remote ID rule information?
Please visit FAA’s official website.
2023-3-18
Use props
DJI Support
Administrator
Flight distance : 2408 ft
Hong Kong
Offline

2.23        I have other questions about Remote ID, what should I do?
Please contact DJI Support.
2023-3-18
Use props
djiuser_Ucr9QFpRozBP
New

United Kingdom
Offline

Can someone please tell me exactly what licences I need to fly my 249g mavic mini in Spain. . Also, do I need permission from the airline to carry my mavic mini . Thankyou
2023-3-19
Use props
Dr.Bees
lvl.1
Flight distance : 85787 ft
United States
Offline

DJI Support Posted at 3-18 03:37
2.16        Will Remote ID reduce battery life?
No

It looks like its draining my battery. so i guess your new policy is to lie and force us to buy more batteries. Good to know you guys are liers

2023-3-20
Use props
DowntownRDB
Core User of DJI
Flight distance : 1722 ft
  • >>>
United States
Offline

Quite the detailed post on Remote ID.  
2023-3-22
Use props
Shawgod
lvl.4
Flight distance : 5173104 ft
United States
Offline

How far is Remote ID broadcasted out?  Does it send to a tower?  I purchased a Mini 2 recently, do you plan on supporting that with RFID?  
2023-3-24
Use props
ro_walker
lvl.4
Brazil
Offline

Very detailed post on Remote ID.  
2023-4-2
Use props
fans83d25485
lvl.1

United States
Offline

Shawgod Posted at 3-24 14:45
How far is Remote ID broadcasted out?  Does it send to a tower?  I purchased a Mini 2 recently, do you plan on supporting that with RFID?

didnt read the post at all, huh? The mini weighs less that 250g, it is not required to broadcast remote ID.
2023-6-7
Use props
Shawgod
lvl.4
Flight distance : 5173104 ft
United States
Offline

fans83d25485 Posted at 6-7 12:58
didnt read the post at all, huh? The mini weighs less that 250g, it is not required to broadcast remote ID.

I am Part 107 and would like to use it if I could.  So RID would be required wouldn't it?
2023-6-8
Use props
fansbe846a9d
lvl.1
Flight distance : 59797 ft
United States
Offline

djiuser_Ucr9QFpRozBP Posted at 3-19 00:14
Can someone please tell me exactly what licences I need to fly my 249g mavic mini in Spain. . Also, do I need permission from the airline to carry my mavic mini . Thankyou

Following. I too would like to make sure my mavic mini pro (no accessories and so it remains below the weight limit) is legal for recreational use and if there are some global restrictions that weight isnt part of the rule.
2023-6-13
Use props
FireJoe
New

United States
Offline

DJI Support Posted at 3-18 03:37
2.7        What actions do I need to take if I want to comply with the Remote ID rule by upgrading RID-compliance firmware?
In theory, no action is required until September 16, 2023. If you are already planning to comply with the Remote ID rule, you may need to take the following three actions.

Hello, I upgraded the firmware of my Mavic 2 zoom to add support of Remote ID and don't see the references shown in this post.   I used the DJI GO4 app and updated, restarted and then launched my sUAS.  Looking through the app I don't see any information showing Remote ID information i.e. the number or that it is transmitting or functional.  How do I find the RID number and know it is functioning?
Thank you,  Joe.
2023-11-25
Use props
djiuser_5PTlB1hLmM0t
lvl.1

Israel
Offline

How can you activate/operate Remote ID Compliance in Israel?
1-9 01:15
Use props
Advanced
You need to log in before you can reply Login | Register now

Credit Rules