Hello,  I just downloaded the firmware for Remote ID and updated the DJI Go 4 App to the newest version, and I was curious how a person would  know if they are actaully broadcasting their Remote ID. Is there going to be an icon on the smart controller while they fly that says RID; similar to the the GPS displays in the top banner bar on the main screen? I tried looking via newtork on my phone, but didn't see it either.

Only thing I can figure is the firmware is trash and they're scrambling to fix it right now.  I don't see RID in the app at all and just like you, there's nothing being transmitted via network or the Drone Scanner apps.  Where you at, DJI???

The apps are very slow in acquiring signal. Some phones must have features enabled. I forget which one. Air Sentinel works much better for me.

Mobilehomer Posted at 11-27 13:09
The apps are very slow in acquiring signal. Some phones must have features enabled. I forget which one. Air Sentinel works much better for me.

I have a smart controller though.

bkuennen Posted at 11-27 13:10
I have a smart controller though.

Install Air Sentinel on your phone.

Hi there. Thank you for reaching out. Kindly please use the DJI remote controller to control the drone to start the motors, then use the WLAN of your cell phone or tablet to scan the Remote ID serial number broadcast by the drone at a location close to the drone. Once you see a string always prefixed with "RID-" followed by a 20-digit alphanumeric Remote ID serial number in the "Available networks" it means that the Remote ID is broadcasting properly. Please note that since the time required for WLAN scanning of different cell phones or tablets is not consistent, it may be necessary to restart the WLAN several times to scan the Remote ID serial number broadcast by the drone. Thank you.

Good morning everyone, I read that after the firmware update, the Mavic 2 can no longer be used with the DJI GROUND STATION PRO app. Can you confirm the news for me, because I use this app regularly. Would it be possible, in this case, to downgrade the firmware?
Mario

I did all of the firmware updates to Mavic 2 Pro and Smart Controller.  I updated the DJI GO 4 app to the latest version.  I started the motors indoors and started watching the WLAN on both iphone and computer.  I didn't see a wireless lan starting with RID.  After I heard the drone say "The Home Point Has Been Updated"  I thought well maybe it can't start broadcasting until it has GPS coordinates.  I began turning off and on the wifi on iphone waiting a minute or so each time and eventially did see the RID- network with my serial number appended to it.

I updated my Mavic 2 Pro and have my Remote ID SN, but when I went to the DJI FlySafe site in order to submit my unlocking request for my next mission, it won't allow me to add that new ID SN. Why?

Specialist Posted at 11-29 11:42
I updated my Mavic 2 Pro and have my Remote ID SN, but when I went to the DJI FlySafe site in order to submit my unlocking request for my next mission, it won't allow me to add that new ID SN. Why?

Hi, Specialist. Are you still experiencing the issue? If so I suggest sending an email to our DJI Flysafe Department at flysafe@dji.com for us to be able to assist you further. We appreciate your patience.

DJI Paladin Posted at 11-27 23:16
Hi there. Thank you for reaching out. Kindly please use the DJI remote controller to control the drone to start the motors, then use the WLAN of your cell phone or tablet to scan the Remote ID serial number broadcast by the drone at a location close to the drone. Once you see a string always prefixed with "RID-" followed by a 20-digit alphanumeric Remote ID serial number in the "Available networks" it means that the Remote ID is broadcasting properly. Please note that since the time required for WLAN scanning of different cell phones or tablets is not consistent, it may be necessary to restart the WLAN several times to scan the Remote ID serial number broadcast by the drone. Thank you.

Is this done outside or inside? I'm guessing it is done inside connected to WiFi then outside to check if it's broadcasting. I have a Smart Controller and don't see the RID number on my IPhone or windows laptop WiFi listed networks. Thanks for your help.

fansb445a0a6 Posted at 12-17 00:04
Is this done outside or inside? I'm guessing it is done inside connected to WiFi then outside to check if it's broadcasting. I have a Smart Controller and don't see the RID number on my IPhone or windows laptop WiFi listed networks. Thanks for your help.

Thank you for your response. Kindly please try this outdoors and please enable the location access on your mobile device and check. Please let us know. We appreciate your valued support.

IZ1Mario Posted at 11-28 01:20
Good morning everyone, I read that after the firmware update, the Mavic 2 can no longer be used with the DJI GROUND STATION PRO app. Can you confirm the news for me, because I use this app regularly. Would it be possible, in this case, to downgrade the firmware?
Mario

It's possible to downgrade the drone with the DJI Assistant 2 (Consumer Drones Series) Application.

DJI Tony Posted at 2023-12-8 02:42
Hi, Specialist. Are you still experiencing the issue? If so I suggest sending an email to our DJI Flysafe Department at  for us to be able to assist you further. We appreciate your patience.

I was able to figure it out, everything is working as it should.

Specialist Posted at 1-17 18:28
I was able to figure it out, everything is working as it should.

Awesome. I'm glad you managed to get it to work. Please don't hesitate to reach us if you need further assistance. Have a great day.

DJI Paladin Posted at 2023-11-27 23:16
Hi there. Thank you for reaching out. Kindly please use the DJI remote controller to control the drone to start the motors, then use the WLAN of your cell phone or tablet to scan the Remote ID serial number broadcast by the drone at a location close to the drone. Once you see a string always prefixed with "RID-" followed by a 20-digit alphanumeric Remote ID serial number in the "Available networks" it means that the Remote ID is broadcasting properly. Please note that since the time required for WLAN scanning of different cell phones or tablets is not consistent, it may be necessary to restart the WLAN several times to scan the Remote ID serial number broadcast by the drone. Thank you.

This is a ridiculous process. Why are these Remote IDs not listed in the About tab of the app, alongside the other SNs???

Are you TRYING to make this as difficult as possible?

Pilot_Ron Posted at 2-16 10:08
This is a ridiculous process. Why are these Remote IDs not listed in the About tab of the app, alongside the other SNs???

Are you TRYING to make this as difficult as possible?

Hi there. Thank you for reaching out. My apologies if the response did not meet your expectations. Can you please tell us what specific DJI product are you using so we can provide you an accurate information? Please keep us posted.

Hi, having the same trouble as mentioned by posters previously.  After updating both the Mavic 2 Pro and Smart Controller I'm getting an error code 180 that prevents me from flying.  Saw advice to use the lightning browser, go to DJI site and download the Go 4 app from there, but I don't see it as any option.  Any advice?

Update:  made it through that error...now getting "Remote ID error.  Unable to take off.  Make sure DJI Fly can access mobile device location."  I'm using a smart controller.

Update 2:  Not sure how I did it.  But I did it.  I'd now like to thanks myself for talking myself through this crisis.

DJI Paladin Posted at 2023-11-27 23:16
Hi there. Thank you for reaching out. Kindly please use the DJI remote controller to control the drone to start the motors, then use the WLAN of your cell phone or tablet to scan the Remote ID serial number broadcast by the drone at a location close to the drone. Once you see a string always prefixed with "RID-" followed by a 20-digit alphanumeric Remote ID serial number in the "Available networks" it means that the Remote ID is broadcasting properly. Please note that since the time required for WLAN scanning of different cell phones or tablets is not consistent, it may be necessary to restart the WLAN several times to scan the Remote ID serial number broadcast by the drone. Thank you.

Hi DJI,
I downloaded the latest firmware, latest DJI GO 4 app, and followed your instruction, but can’t find the RID by WLAN broadcast.  Can’t also find it in App as well.
I’m not in US now, but will be.  Is there any other way to find my RID?  So that I can register my Mavic 2 Pro and make sure everything works before my trip to US?

DJI Paladin Posted at 2023-11-27 23:16
Hi there. Thank you for reaching out. Kindly please use the DJI remote controller to control the drone to start the motors, then use the WLAN of your cell phone or tablet to scan the Remote ID serial number broadcast by the drone at a location close to the drone. Once you see a string always prefixed with "RID-" followed by a 20-digit alphanumeric Remote ID serial number in the "Available networks" it means that the Remote ID is broadcasting properly. Please note that since the time required for WLAN scanning of different cell phones or tablets is not consistent, it may be necessary to restart the WLAN several times to scan the Remote ID serial number broadcast by the drone. Thank you.

Hi DJI,
I downloaded the latest firmware, latest DJI GO 4 app, and followed your instruction, but can’t find the RID by WLAN broadcast.  Can’t also find it in App as well.
I’m not in US now, but will be.  Is there any other way to find my RID?  So that I can register my Mavic 2 Pro and make sure everything works before my trip to US?

fansc55b1376 Posted at 3-1 15:38
Hi DJI,
I downloaded the latest firmware, latest DJI GO 4 app, and followed your instruction, but can’t find the RID by WLAN broadcast.  Can’t also find it in App as well.
I’m not in US now, but will be.  Is there any other way to find my RID?  So that I can register my Mavic 2 Pro and make sure everything works before my trip to US?

Your RID is 1581F[Your regular drone serial Number]0

for example 1581F0M6DFAC0012ABC0

It's a 20 character string to use for the FAA registration.

FloridaNext Posted at 3-1 17:50
Your RID is 1581F[Your regular drone serial Number]0

for example 1581F0M6DFAC0012ABC0

Thank you FloridaNext.
I registered successfully

DJI Paladin Posted at 2023-11-27 23:16
Hi there. Thank you for reaching out. Kindly please use the DJI remote controller to control the drone to start the motors, then use the WLAN of your cell phone or tablet to scan the Remote ID serial number broadcast by the drone at a location close to the drone. Once you see a string always prefixed with "RID-" followed by a 20-digit alphanumeric Remote ID serial number in the "Available networks" it means that the Remote ID is broadcasting properly. Please note that since the time required for WLAN scanning of different cell phones or tablets is not consistent, it may be necessary to restart the WLAN several times to scan the Remote ID serial number broadcast by the drone. Thank you.

I followed these instructions from DJI Paladin.   Finally, the remote ID signal did show up on my Iphone, but the signal comes and goes.    The signal never shows up on my 2 Crystalsky tablets (updated to the latest firmware).   I also do not see the signal on my RID scanning App, Drone Scanner.  I know that this app works because I have tested it with my Remote ID module for Inspire 2.
How can I be sure that Mavic 2 Pro Remote ID is actually broadcasting?

fansc55b1376 Posted at 3-1 15:38
Hi DJI,
I downloaded the latest firmware, latest DJI GO 4 app, and followed your instruction, but can’t find the RID by WLAN broadcast.  Can’t also find it in App as well.
I’m not in US now, but will be.  Is there any other way to find my RID?  So that I can register my Mavic 2 Pro and make sure everything works before my trip to US?

Hi there. Sorry for the late response. We're glad that you have managed to register your unit. Should you have other inquiries, feel free to contact us. Have a good one!

grangecam Posted at 3-2 08:40
I followed these instructions from DJI Paladin.   Finally, the remote ID signal did show up on my Iphone, but the signal comes and goes.    The signal never shows up on my 2 Crystalsky tablets (updated to the latest firmware).   I also do not see the signal on my RID scanning App, Drone Scanner.  I know that this app works because I have tested it with my Remote ID module for Inspire 2.
How can I be sure that Mavic 2 Pro Remote ID is actually broadcasting?

Hi there. Thank you for reaching out. Kindly please test it outdoors and make sure to enable the location access on your mobile device and check if the issue persists.

Specialist Posted at 1-17 18:28
I was able to figure it out, everything is working as it should.

So what did you do ??

- I have been outside - acquired gps sync - taken off - and none of my scanner pick it up nor do I see it in my ssid list, yet I bought a RID module from holy stone and within seconds I can see it in my scanners…..

djiuser_ASNLG5cYmhQa Posted at 3-15 18:44
So what did you do ??

- I have been outside - acquired gps sync - taken off - and none of my scanner pick it up nor do I see it in my ssid list, yet I bought a RID module from holy stone and within seconds I can see it in my scanners…..

Hi there. You can confirm that the Remote ID is working by using the DJI remote controller to control the drone to start the motors, then use the WLAN of your cell phone or tablet to scan the Remote ID serial number broadcast by the drone at a location close to the drone Note

if you can see a string always prefixed with “RID-” followed by a 20-digit alphanumeric Remote ID serial number in the "Available networks", it means that the Remote ID is broadcasting properly.
Since the time required for WLAN scanning of different cell phones or tablets is not consistent, it may be necessary to restart the WLAN several times to scan the Remote ID serial number broadcast by the drone. Have a great day.

djiuser_IxvPmktgP79y Posted at 2023-11-28 18:37
I did all of the firmware updates to Mavic 2 Pro and Smart Controller.  I updated the DJI GO 4 app to the latest version.  I started the motors indoors and started watching the WLAN on both iphone and computer.  I didn't see a wireless lan starting with RID.  After I heard the drone say "The Home Point Has Been Updated"  I thought well maybe it can't start broadcasting until it has GPS coordinates.  I began turning off and on the wifi on iphone waiting a minute or so each time and eventially did see the RID- network with my serial number appended to it.

Well this really sucks, so it can be up to 10 or 20 minutes before you can take off, if ever!!

Could anyone guide me where to find remote ID on DJI Marvic 2 Pro?

I appreciate this thread and DJI's help here. I'm trying to register my drone in Japan and having a very difficult time getting the remote ID and doing the registration process with DIPS registration to fly legally in Japan. So many errors. But I'll keep trying. The screen shot of the registration ID in the WLAN was very helpful in understanding that part. Thanks.

I'm using a Maveric Air II, so it's an older drone but I hope I can make the remote ID work.