Hi Guys,

Having a slight issue where the upgrade will appear to have completed but the gimbal goes to a solid red / continuous long beep.  I had this problem on the last update 1.3.2 as well.  The basic log will show that the update failed but when you go to try again the log then reports that the firmware is identical to the one already on the craft.

Seen a few people look over their extensive logs (see below).  Can't help noticing there's a device not detected in there.  Any ideas ?

Cheers,

Paul.

[00011745][01 00] Firmware upgrade finished successfully.
[00011870]Done.

[00011980]Packet [C:\P3S_FW_V01.03.0020.bin] resumed, card sn [0x80ce0c7a].
[00012129]Packet vlink 01.03.0020 <-> 01.01.0009.
[00012272]Version checking[2]...
[00012430][03 05][00] v34.2.0.8 -> v34.2.0.9 need upgrade.
[00012590][03 06][00] v2.1.6.18 -> v2.2.6.19 need upgrade.
[00012704][04 00][00] v1.36.0.0 -> v1.40.0.0 need upgrade.
[00012814][09 00][00] v1.7.0.3 -> v1.7.0.3
[00012950][11 00][00] v1.6.0.0 -> v1.7.0.0 need upgrade.
[00013043][12 00][00] v1.8.0.0 -> v1.8.0.0
[00013117][12 01][00] v1.8.0.0 -> v1.8.0.0
[00013217][12 02][00] v1.8.0.0 -> v1.8.0.0
[00013314][12 03][00] v1.8.0.0 -> v1.8.0.0
[00045851][15 00][00] device not detected.
[00045942][17 00][00] v1.1.1.2 -> v1.1.1.7 need upgrade.
[00046058][17 01][00] v1.0.2.4 -> v1.0.2.7 need upgrade.
[00046109][19 00][00] v1.0.8.59 -> v1.0.8.96 need upgrade.
[00046145][01 00][05] v1.20.3419 -> v1.20.3419
[00046184][01 01][00] v1.7.2735 -> v1.20.3419 need upgrade
[00046219]Done.

[00046256]Firmware upgrading[2]...
[00046409][01 01] Firmware upgrade start...
[00076710][01 01] Firmware upgrade finished successfully.
[00076786][17 00] Firmware upgrade start...
[00183441][17 00] Firmware upgrade finished successfully.
[00183489][17 01] Firmware upgrade start...
[00251804][17 01] Firmware upgrade finished successfully.
[00251858][11 00] Firmware upgrade start...
[00304843][11 00] Firmware upgrade finished successfully.
[00304901][03 05] Firmware upgrade start...
[00378157][03 05] Firmware upgrade finished successfully.
[00378390][03 06] Firmware upgrade start...
[00678852][03 06] Firmware upgrade finished successfully.
[00681904][19 00] Firmware upgrade start...
[00696385][19 00] Firmware upgrade finish failed (step = 4, err = 0xaa, idx = 0, los = 1, ng = 0, usb = 1).
[00726452][04 00] Firmware upgrade start...
[00784524][04 00] Firmware upgrade finished successfully.
[00784564]Done.

[00784598]Version checking[3]...
[00784813][03 05][05] v34.2.0.9 -> v34.2.0.9
[00784888][03 06][05] v2.2.6.19 -> v2.2.6.19
[00784929][04 00][05] v1.40.0.0 -> v1.40.0.0
[00784988][09 00][00] v1.7.0.3 -> v1.7.0.3
[00785113][11 00][05] v1.7.0.0 -> v1.7.0.0
[00785197][12 00][00] v1.8.0.0 -> v1.8.0.0
[00785289][12 01][00] v1.8.0.0 -> v1.8.0.0
[00785377][12 02][00] v1.8.0.0 -> v1.8.0.0
[00785462][12 03][00] v1.8.0.0 -> v1.8.0.0
[00817996][15 00][00] device not detected.
[00818084][17 00][05] v1.1.1.7 -> v1.1.1.7
[00818205][17 01][05] v1.0.2.7 -> v1.0.2.7
[00818270][19 00][00] v1.0.8.59 -> v1.0.8.96 need upgrade.
[00818310][01 00][05] v1.20.3419 -> v1.20.3419
[00818350][01 01][05] v1.20.3419 -> v1.20.3419
[00818387]Done.

[00818423]Firmware upgrading[3]...
[00821344][19 00] Firmware upgrade start...
[00835801][19 00] Firmware upgrade finish failed (step = 4, err = 0xaa, idx = 0, los = 1, ng = 0, usb = 1).
[00865838]Done.

[00865873]Version checking[4]...
[00865952][03 05][05] v34.2.0.9 -> v34.2.0.9
[00866032][03 06][05] v2.2.6.19 -> v2.2.6.19
[00866072][04 00][05] v1.40.0.0 -> v1.40.0.0
[00866132][09 00][00] v1.7.0.3 -> v1.7.0.3
[00866253][11 00][05] v1.7.0.0 -> v1.7.0.0
[00866343][12 00][00] v1.8.0.0 -> v1.8.0.0
[00866422][12 01][00] v1.8.0.0 -> v1.8.0.0
[00866507][12 02][00] v1.8.0.0 -> v1.8.0.0
[00866607][12 03][00] v1.8.0.0 -> v1.8.0.0
[00899143][15 00][00] device not detected.
[00899227][17 00][05] v1.1.1.7 -> v1.1.1.7
[00899344][17 01][05] v1.0.2.7 -> v1.0.2.7
[00899394][19 00][00] v1.0.8.59 -> v1.0.8.96 need upgrade.
[00899428][01 00][05] v1.20.3419 -> v1.20.3419
[00899464][01 01][05] v1.20.3419 -> v1.20.3419
[00899498]Done.

[00899539]Firmware upgrading[4]...
[00902423][19 00] Firmware upgrade start...
[01078467][19 00] Firmware upgrade finished successfully.
[01078503]Done.

[01078545]Version checking[5]...
[01078630][03 05][05] v34.2.0.9 -> v34.2.0.9
[01078686][03 06][05] v2.2.6.19 -> v2.2.6.19
[01078763][04 00][05] v1.40.0.0 -> v1.40.0.0
[01078820][09 00][00] v1.7.0.3 -> v1.7.0.3
[01079030][11 00][05] v1.7.0.0 -> v1.7.0.0
[01079145][12 00][00] v1.8.0.0 -> v1.8.0.0
[01079242][12 01][00] v1.8.0.0 -> v1.8.0.0
[01079321][12 02][00] v1.8.0.0 -> v1.8.0.0
[01079395][12 03][00] v1.8.0.0 -> v1.8.0.0
[01111935][15 00][00] device not detected.
[01111998][17 00][05] v1.1.1.7 -> v1.1.1.7
[01112117][17 01][05] v1.0.2.7 -> v1.0.2.7
[01112182][19 00][05] v1.0.8.96 -> v1.0.8.96
[01112221][01 00][05] v1.20.3419 -> v1.20.3419
[01112260][01 01][05] v1.20.3419 -> v1.20.3419
[01112297]Packet upgrade failed at version checking.



[00011991]========== remo-con disconnect. boot(15) ============
[00012034]Packet [C:\P3S_FW_V01.03.0020.bin] detected, card sn [0x80ce0c7a].
[00012072]Packet upgrade start...

[00012123]Packet checking...
[00012164]Packet vlink 01.03.0020 <-> 01.01.0009.
[00012233]Done.

[00012269]Version checking[1]...
[00012336][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012423][03 06][00] v2.2.6.19 -> v2.2.6.19
[00012467][04 00][00] v1.40.0.0 -> v1.40.0.0
[00012524][09 00][00] v1.7.0.3 -> v1.7.0.3
[00012636][11 00][00] v1.7.0.0 -> v1.7.0.0
[00012735][12 00][00] v1.8.0.0 -> v1.8.0.0
[00012810][12 01][00] v1.8.0.0 -> v1.8.0.0
[00012910][12 02][00] v1.8.0.0 -> v1.8.0.0
[00013010][12 03][00] v1.8.0.0 -> v1.8.0.0
[00013058][15 00][00] v1.1.2.0 -> v1.1.2.0
[00013146][17 00][00] v1.1.1.7 -> v1.1.1.7
[00013266][17 01][00] v1.0.2.7 -> v1.0.2.7
[00013325][19 00][00] v1.0.8.96 -> v1.0.8.96
[00013365][01 00][00] v1.20.3419 -> v1.20.3419
[00013400][01 01][00] v1.20.3419 -> v1.20.3419
[00013440]Packet upgrade cancelled at version checking.



[00011989]========== remo-con disconnect. boot(15) ============
[00012027]Packet [C:\P3S_FW_V01.03.0020.bin] detected, card sn [0x80ce0c7a].
[00012070]Packet upgrade start...

[00012114]Packet checking...
[00012163]Packet vlink 01.03.0020 <-> 01.01.0009.
[00012199]Record vlink 01.03.0020 <-> 01.01.0009 (flow = 0).
[00012235]Done.

[00012278]Version checking[1]...
[00012470][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012556][03 06][00] v2.2.6.19 -> v2.2.6.19
[00012601][04 00][00] v1.40.0.0 -> v1.40.0.0
[00012665][09 00][00] v1.7.0.3 -> v1.7.0.3
[00012790][11 00][00] v1.7.0.0 -> v1.7.0.0
[00012880][12 00][00] v1.8.0.0 -> v1.8.0.0
[00012980][12 01][00] v1.8.0.0 -> v1.8.0.0
[00013080][12 02][00] v1.8.0.0 -> v1.8.0.0
[00013180][12 03][00] v1.8.0.0 -> v1.8.0.0
[00013221][15 00][00] v1.1.2.0 -> v1.1.2.0
[00013315][17 00][00] v1.1.1.7 -> v1.1.1.7
[00013460][17 01][00] v1.0.2.7 -> v1.0.2.7
[00013525][19 00][00] v1.0.8.96 -> v1.0.8.96
[00013569][01 00][00] v1.20.3419 -> v1.20.3419
[00013609][01 01][00] v1.20.3419 -> v1.20.3419
[00013657]Packet upgrade cancelled at version checking.



[00012283]========== remo-con disconnect. boot(15) ============
[00012324]Packet [C:\P3S_FW_V01.04.0010.bin] detected, card sn [0x00774ac7].
[00012363]Packet upgrade start...

[00012416]Packet checking...
[00012463]Packet vlink 01.04.0010 <-> 01.03.0020.
[00012504]Record vlink 01.03.0020 <-> 01.01.0009 (flow = 0).
[00012546]Done.

[00012587]Version checking[1]...
[00012658][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012738][03 06][00] v2.2.6.19 -> v2.3.0.13 need upgrade.
[00012784][04 00][00] v1.40.0.0 -> v1.41.0.0 need upgrade.
[00012838][09 00][00] v1.7.0.3 -> v1.7.0.3
[00012979][11 00][00] v1.7.0.0 -> v1.7.0.0
[00013068][12 00][00] v1.8.0.0 -> v1.10.0.0 need upgrade.
[00013158][12 01][00] v1.8.0.0 -> v1.10.0.0 need upgrade.
[00013243][12 02][00] v1.8.0.0 -> v1.10.0.0 need upgrade.
[00013359][12 03][00] v1.8.0.0 -> v1.10.0.0 need upgrade.
[00045900][15 00][00] device not detected.
[00045985][17 00][00] v1.1.1.7 -> v1.1.1.7
[00046105][17 01][00] v1.0.2.7 -> v1.0.2.7
[00046162][19 00][00] v1.0.8.96 -> v1.0.8.96
[00046202][01 00][00] v1.20.3419 -> v1.21.3647 need upgrade
[00046251][01 01][00] v1.20.3419 -> v1.21.3647 need upgrade
[00046291]Done.

[00048330]Waiting for user confirm...
[00058369]Timeout, start upgrade automatically.

[00058542]Firmware upgrading[1]...
[00073481][01 00] Firmware upgrade start...
[00011747][01 00] Firmware upgrade finished successfully.
[00011918]Done.

[00011968]Packet [C:\P3S_FW_V01.04.0010.bin] resumed, card sn [0x00774ac7].
[00012024]Packet vlink 01.04.0010 <-> 01.03.0020.
[00012070]Record vlink 01.03.0020 <-> 01.01.0009 (flow = 0).
[00012110]Version checking[2]...
[00012192][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012272][03 06][00] v2.2.6.19 -> v2.3.0.13 need upgrade.
[00012322][04 00][00] v1.40.0.0 -> v1.41.0.0 need upgrade.
[00012392][09 00][00] v1.7.0.3 -> v1.7.0.3
[00012513][11 00][00] v1.7.0.0 -> v1.7.0.0
[00012606][12 00][00] v1.8.0.0 -> v1.10.0.0 need upgrade.
[00012706][12 01][00] v1.8.0.0 -> v1.10.0.0 need upgrade.
[00012826][12 02][00] v1.8.0.0 -> v1.10.0.0 need upgrade.
[00012927][12 03][00] v1.8.0.0 -> v1.10.0.0 need upgrade.
[00045471][15 00][00] device not detected.
[00045563][17 00][00] v1.1.1.7 -> v1.1.1.7
[00045683][17 01][00] v1.0.2.7 -> v1.0.2.7
[00045733][19 00][00] v1.0.8.96 -> v1.0.8.96
[00045771][01 00][05] v1.21.3647 -> v1.21.3647
[00045812][01 01][00] v1.20.3419 -> v1.21.3647 need upgrade
[00045854]Done.

[00045894]Firmware upgrading[2]...
[00046048][01 01] Firmware upgrade start...
[00076327][01 01] Firmware upgrade finished successfully.
[00076393][12 00] Firmware upgrade start...
[00151055][12 00] Firmware upgrade finished successfully.
[00151109][12 01] Firmware upgrade start...
[00225918][12 01] Firmware upgrade finished successfully.
[00225976][12 02] Firmware upgrade start...
[00291795][12 02] Firmware upgrade finished successfully.
[00291853][12 03] Firmware upgrade start...
[00353809][12 03] Firmware upgrade finished successfully.
[00354060][03 06] Firmware upgrade start...
[00702427][03 06] Firmware upgrade finished successfully.
[00702499][04 00] Firmware upgrade start...
[00760510][04 00] Firmware upgrade finished successfully.
[00760557]Done.

[00760599]Version checking[3]...
[00760757][03 05][00] v34.2.0.9 -> v34.2.0.9
[00760818][03 06][05] v2.3.0.13 -> v2.3.0.13
[00760868][04 00][05] v1.41.0.0 -> v1.41.0.0
[00760930][09 00][00] v1.7.0.3 -> v1.7.0.3
[00761041][11 00][00] v1.7.0.0 -> v1.7.0.0
[00761130][12 00][05] v1.10.0.0 -> v1.10.0.0
[00761210][12 01][05] v1.10.0.0 -> v1.10.0.0
[00761296][12 02][05] v1.10.0.0 -> v1.10.0.0
[00761385][12 03][05] v1.10.0.0 -> v1.10.0.0
[00793930][15 00][00] device not detected.
[00794007][17 00][00] v1.1.1.7 -> v1.1.1.7
[00794127][17 01][00] v1.0.2.7 -> v1.0.2.7
[00794192][19 00][00] v1.0.8.96 -> v1.0.8.96
[00794237][01 00][05] v1.21.3647 -> v1.21.3647
[00794279][01 01][05] v1.21.3647 -> v1.21.3647
[00794327]Packet upgrade failed at version checking.



[00012278]========== remo-con disconnect. boot(15) ============
[00012315]Packet [C:\P3S_FW_V01.04.0010.bin] detected, card sn [0x80ce0c7a].
[00012361]Packet upgrade start...

[00012404]Packet checking...
[00012446]Packet vlink 01.04.0010 <-> 01.03.0020.
[00012486]Record vlink 01.03.0020 <-> 01.01.0009 (flow = 0).
[00012523]Done.

[00012564]Version checking[1]...
[00012648][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012729][03 06][00] v2.3.0.13 -> v2.3.0.13
[00012779][04 00][00] v1.41.0.0 -> v1.41.0.0
[00012827][09 00][00] v1.7.0.3 -> v1.7.0.3
[00015448][11 00][00] v1.7.0.0 -> v1.7.0.0
[00015532][12 00][00] v1.10.0.0 -> v1.10.0.0
[00015622][12 01][00] v1.10.0.0 -> v1.10.0.0
[00015722][12 02][00] v1.10.0.0 -> v1.10.0.0
[00015802][12 03][00] v1.10.0.0 -> v1.10.0.0
[00046342][15 00][00] device not detected.
[00046434][17 00][00] v1.1.1.7 -> v1.1.1.7
[00046563][17 01][00] v1.0.2.7 -> v1.0.2.7
[00046629][19 00][00] v1.0.8.96 -> v1.0.8.96
[00046669][01 00][00] v1.21.3647 -> v1.21.3647
[00046707][01 01][00] v1.21.3647 -> v1.21.3647
[00046746]Packet upgrade failed at version checking.



[00012012]========== remo-con disconnect. boot(15) ============
[00012065]Packet [C:\P3S_FW_V01.04.0010.bin] detected, card sn [0x80ce0c7a].
[00012200]Packet upgrade start...

[00012247]Packet checking...
[00012290]Packet vlink 01.04.0010 <-> 01.03.0020.
[00012333]Record vlink 01.03.0020 <-> 01.01.0009 (flow = 0).
[00012375]Done.

[00012416]Version checking[1]...
[00012493][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012573][03 06][00] v2.3.0.13 -> v2.3.0.13
[00012623][04 00][00] v1.41.0.0 -> v1.41.0.0
[00012677][09 00][00] v1.7.0.3 -> v1.7.0.3
[00012798][11 00][00] v1.7.0.0 -> v1.7.0.0
[00012881][12 00][00] v1.10.0.0 -> v1.10.0.0
[00012972][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013061][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013146][12 03][00] v1.10.0.0 -> v1.10.0.0
[00013190][15 00][00] v1.1.2.0 -> v1.1.2.0
[00013281][17 00][00] v1.1.1.7 -> v1.1.1.7
[00013401][17 01][00] v1.0.2.7 -> v1.0.2.7
[00013456][19 00][00] v1.0.8.96 -> v1.0.8.96
[00013498][01 00][00] v1.21.3647 -> v1.21.3647
[00013543][01 01][00] v1.21.3647 -> v1.21.3647
[00013584]Packet upgrade cancelled at version checking.



[00012002]========== remo-con disconnect. boot(15) ============
[00012041]Packet [C:\P3S_FW_V01.04.0010.bin] detected, card sn [0x80ce0c7a].
[00012079]Packet upgrade start...

[00012120]Packet checking...
[00012161]Packet vlink 01.04.0010 <-> 01.03.0020.
[00012206]Record vlink 01.04.0010 <-> 01.03.0020 (flow = 0).
[00012243]Done.

[00012282]Version checking[1]...
[00012351][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012431][03 06][00] v2.3.0.13 -> v2.3.0.13
[00012476][04 00][00] v1.41.0.0 -> v1.41.0.0
[00012536][09 00][00] v1.7.0.3 -> v1.7.0.3
[00012651][11 00][00] v1.7.0.0 -> v1.7.0.0
[00012740][12 00][00] v1.10.0.0 -> v1.10.0.0
[00012824][12 01][00] v1.10.0.0 -> v1.10.0.0
[00012905][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013005][12 03][00] v1.10.0.0 -> v1.10.0.0
[00013052][15 00][00] v1.1.2.0 -> v1.1.2.0
[00013145][17 00][00] v1.1.1.7 -> v1.1.1.7
[00013261][17 01][00] v1.0.2.7 -> v1.0.2.7
[00013314][19 00][00] v1.0.8.96 -> v1.0.8.96
[00013354][01 00][00] v1.21.3647 -> v1.21.3647
[00013467][01 01][00] v1.21.3647 -> v1.21.3647
[00013507]Packet upgrade cancelled at version checking.

paul

I see the error of the missing module ( its the Air End USB transmit  ), but on later logs it seems to have corrected itself..

What kind of beep is it doing? can you post a video?

What's the Air End USB transmit ?

I've posted a video to: http://www.alphacrust.co.uk/videos/IMG_0370.m4v

You'll see the solid red light on the gimbal and you can probably just hear the solid constant one tone beep below the RF noise.

Do we think the upgrades are getting to the end, or should I be worried that something is missing ?

sploodge Posted at 2015-9-7 13:43
paul

I see the error of the missing module ( its the Air End USB transmit  ), but on la ...

Hey splooge, is there a post or document that tells what piece of equipment each of those upgrade numbers is for? Be kind of interesting to know.

i had the same issue this morning, i tried everything from reformatting the card, switching out batteries, letting it sit, re-downloading the upgrade. nothing seemed to work. for whatever reason it just seemed to make it all the way to the end, but im not positive. my app says it's updated but im going to post my longer log, can anyone with more knowledge take a look and see if this issue corrected itself?

[00011833][01 00] Firmware upgrade finished successfully.
[00011953]Done.

[00012061]Packet [C:\P3S_FW_V01.02.0007.bin] resumed, card sn [0x80ce1834].
[00012207]Version checking[2]...
[00012350][03 05][00] v34.2.0.8 -> v34.2.0.9 need upgrade.
[00012510][03 06][00] v2.1.6.18 -> v2.2.6.8 need upgrade.
[00012623][04 00][00] v1.36.0.0 -> v1.38.0.0 need upgrade.
[00012750][09 00][00] v1.7.0.3 -> v1.7.0.3
[00012929][11 00][00] v1.6.0.0 -> v1.6.0.0
[00013094][12 00][00] v1.8.0.0 -> v1.8.0.0
[00013184][12 01][00] v1.8.0.0 -> v1.8.0.0
[00013264][12 02][00] v1.8.0.0 -> v1.8.0.0
[00013339][12 03][00] v1.8.0.0 -> v1.8.0.0
[00013377][15 00][00] v1.1.2.0 -> v1.1.2.0
[00013455][17 00][00] v1.1.1.2 -> v1.1.1.6 need upgrade.
[00013575][17 01][00] v1.0.2.4 -> v1.0.2.5 need upgrade.
[00013630][19 00][00] v1.0.8.59 -> v1.0.8.96 need upgrade.
[00013666][01 00][05] v1.14.3061 -> v1.14.3061
[00013701][01 01][00] v1.7.2735 -> v1.14.3061 need upgrade
[00013740]Done.

[00013773]Firmware upgrading[2]...
[00013927][01 01] Firmware upgrade start...
[00044197][01 01] Firmware upgrade finished successfully.
[00044260][17 00] Firmware upgrade start...
[00162122][17 00] Firmware upgrade finished successfully.
[00162169][17 01] Firmware upgrade start...
[00236565][17 01] Firmware upgrade finished successfully.
[00236617][03 05] Firmware upgrade start...
[00307659][03 05] Firmware upgrade finished successfully.
[00307896][03 06] Firmware upgrade start...
[00643451][03 06] Firmware upgrade finished successfully.
[00646518][19 00] Firmware upgrade start...
[00812189][19 00] Firmware upgrade finished successfully.
[00812251][04 00] Firmware upgrade start...
[00869417][04 00] Firmware upgrade finished successfully.
[00869453]Done.

[00869486]Version checking[3]...
[00869568][03 05][05] v34.2.0.9 -> v34.2.0.9
[00869648][03 06][05] v2.2.6.8 -> v2.2.6.8
[00869694][04 00][05] v1.38.0.0 -> v1.38.0.0
[00869744][09 00][00] v1.7.0.3 -> v1.7.0.3
[00869868][11 00][00] v1.6.0.0 -> v1.6.0.0
[00870038][12 00][00] v1.8.0.0 -> v1.8.0.0
[00870118][12 01][00] v1.8.0.0 -> v1.8.0.0
[00870218][12 02][00] v1.8.0.0 -> v1.8.0.0
[00870318][12 03][00] v1.8.0.0 -> v1.8.0.0
[00870357][15 00][00] v1.1.2.0 -> v1.1.2.0
[00870433][17 00][05] v1.1.1.6 -> v1.1.1.6
[00870553][17 01][05] v1.0.2.5 -> v1.0.2.5
[00870603][19 00][05] v1.0.8.96 -> v1.0.8.96
[00870641][01 00][05] v1.14.3061 -> v1.14.3061
[00870675][01 01][05] v1.14.3061 -> v1.14.3061
[00870709]Packet upgrade finish successfully.



[00012856]========== remo-con disconnect. boot(15) ============
[00012946]Packet [C:\P3S_FW_V01.02.0008.bin] detected, card sn [0x80ce1834].
[00013058]Packet upgrade start...

[00013204]Packet checking...
[00013320]Done.

[00013430]Version checking[1]...
[00013597][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013737][03 06][00] v2.2.6.8 -> v2.2.6.8
[00013800][04 00][00] v1.38.0.0 -> v1.38.0.0
[00013922][09 00][00] v1.7.0.3 -> v1.7.0.3
[00014120][11 00][00] v1.6.0.0 -> v1.6.0.0
[00014303][12 00][00] v1.8.0.0 -> v1.8.0.0
[00014454][12 01][00] v1.8.0.0 -> v1.8.0.0
[00014607][12 02][00] v1.8.0.0 -> v1.8.0.0
[00014777][12 03][00] v1.8.0.0 -> v1.8.0.0
[00047366][15 00][00] device not detected.
[00047504][17 00][00] v1.1.1.6 -> v1.1.1.6
[00047687][17 01][00] v1.0.2.5 -> v1.0.2.5
[00047844][19 00][00] v1.0.8.96 -> v1.0.8.96
[00047954][01 00][00] v1.14.3061 -> v1.14.3090 need upgrade
[00048060][01 01][00] v1.14.3061 -> v1.14.3090 need upgrade
[00048173]Done.

[00050283]Waiting for user confirm...
[00060379]Timeout, start upgrade automatically.

[00060593]Firmware upgrading[1]...
[00075967][01 00] Firmware upgrade start...
[00011742][01 00] Firmware upgrade finished successfully.
[00011793]Done.

[00011825]Packet [C:\P3S_FW_V01.02.0008.bin] resumed, card sn [0x80ce1834].
[00011871]Version checking[2]...
[00011950][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012010][03 06][00] v2.2.6.8 -> v2.2.6.8
[00012057][04 00][00] v1.38.0.0 -> v1.38.0.0
[00012115][09 00][00] v1.7.0.3 -> v1.7.0.3
[00012333][11 00][00] v1.6.0.0 -> v1.6.0.0
[00012420][12 00][00] v1.8.0.0 -> v1.8.0.0
[00012505][12 01][00] v1.8.0.0 -> v1.8.0.0
[00012605][12 02][00] v1.8.0.0 -> v1.8.0.0
[00012685][12 03][00] v1.8.0.0 -> v1.8.0.0
[00012729][15 00][00] v1.1.2.0 -> v1.1.2.0
[00012815][17 00][00] v1.1.1.6 -> v1.1.1.6
[00012939][17 01][00] v1.0.2.5 -> v1.0.2.5
[00012995][19 00][00] v1.0.8.96 -> v1.0.8.96
[00013029][01 00][05] v1.14.3090 -> v1.14.3090
[00013073][01 01][00] v1.14.3061 -> v1.14.3090 need upgrade
[00013109]Done.

[00013146]Firmware upgrading[2]...
[00013303][01 01] Firmware upgrade start...
[00043589][01 01] Firmware upgrade finished successfully.
[00043625]Done.

[00043659]Version checking[3]...
[00043737][03 05][00] v34.2.0.9 -> v34.2.0.9
[00043811][03 06][00] v2.2.6.8 -> v2.2.6.8
[00043850][04 00][00] v1.38.0.0 -> v1.38.0.0
[00043902][09 00][00] v1.7.0.3 -> v1.7.0.3
[00044011][11 00][00] v1.6.0.0 -> v1.6.0.0
[00044086][12 00][00] v1.8.0.0 -> v1.8.0.0
[00044167][12 01][00] v1.8.0.0 -> v1.8.0.0
[00044242][12 02][00] v1.8.0.0 -> v1.8.0.0
[00044332][12 03][00] v1.8.0.0 -> v1.8.0.0
[00044371][15 00][00] v1.1.2.0 -> v1.1.2.0
[00044457][17 00][00] v1.1.1.6 -> v1.1.1.6
[00044581][17 01][00] v1.0.2.5 -> v1.0.2.5
[00044637][19 00][00] v1.0.8.96 -> v1.0.8.96
[00044673][01 00][05] v1.14.3090 -> v1.14.3090
[00044709][01 01][05] v1.14.3090 -> v1.14.3090
[00044750]Packet upgrade finish successfully.



[00013216]========== remo-con disconnect. boot(15) ============
[00013355]Packet [C:\P3S_FW_V01.03.0020.bin] detected, card sn [0x80ce1834].
[00013462]Packet upgrade start...

[00013616]Packet checking...
[00013725]Done.

[00013780]Version checking[1]...
[00013943][03 05][00] v34.2.0.9 -> v34.2.0.9
[00014104][03 06][00] v2.2.6.8 -> v2.2.6.19 need upgrade.
[00014216][04 00][00] v1.38.0.0 -> v1.40.0.0 need upgrade.
[00014348][09 00][00] v1.7.0.3 -> v1.7.0.3
[00014543][11 00][00] v1.6.0.0 -> v1.7.0.0 need upgrade.
[00014818][12 00][00] v1.8.0.0 -> v1.8.0.0
[00014983][12 01][00] v1.8.0.0 -> v1.8.0.0
[00015143][12 02][00] v1.8.0.0 -> v1.8.0.0
[00015319][12 03][00] v1.8.0.0 -> v1.8.0.0
[00015429][15 00][00] v1.1.2.0 -> v1.1.2.0
[00015593][17 00][00] v1.1.1.6 -> v1.1.1.7 need upgrade.
[00015793][17 01][00] v1.0.2.5 -> v1.0.2.7 need upgrade.
[00015928][19 00][00] v1.0.8.96 -> v1.0.8.96
[00016037][01 00][00] v1.14.3090 -> v1.20.3419 need upgrade
[00016113][01 01][00] v1.14.3090 -> v1.20.3419 need upgrade
[00016176]Done.

[00018210]Waiting for user confirm...
[00028246]Timeout, start upgrade automatically.

[00028316]Firmware upgrading[1]...
[00040708][01 00] Firmware upgrade start...
[00011731][01 00] Firmware upgrade finished successfully.
[00011782]Done.

[00011816]Packet [C:\P3S_FW_V01.03.0020.bin] resumed, card sn [0x80ce1834].
[00011856]Packet vlink 01.03.0020 <-> 01.01.0009.
[00011922]Version checking[2]...
[00012000][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012059][03 06][00] v2.2.6.8 -> v2.2.6.19 need upgrade.
[00012102][04 00][00] v1.38.0.0 -> v1.40.0.0 need upgrade.
[00012165][09 00][00] v1.7.0.3 -> v1.7.0.3
[00012284][11 00][00] v1.6.0.0 -> v1.7.0.0 need upgrade.
[00012379][12 00][00] v1.8.0.0 -> v1.8.0.0
[00012455][12 01][00] v1.8.0.0 -> v1.8.0.0
[00012535][12 02][00] v1.8.0.0 -> v1.8.0.0
[00012610][12 03][00] v1.8.0.0 -> v1.8.0.0
[00012647][15 00][00] v1.1.2.0 -> v1.1.2.0
[00012735][17 00][00] v1.1.1.6 -> v1.1.1.7 need upgrade.
[00012850][17 01][00] v1.0.2.5 -> v1.0.2.7 need upgrade.
[00012905][19 00][00] v1.0.8.96 -> v1.0.8.96
[00012940][01 00][05] v1.20.3419 -> v1.20.3419
[00012976][01 01][00] v1.14.3090 -> v1.20.3419 need upgrade
[00013010]Done.

[00013053]Firmware upgrading[2]...
[00013193][01 01] Firmware upgrade start...
[00043445][01 01] Firmware upgrade finished successfully.
[00043504][17 00] Firmware upgrade start...
[00140891][17 00] Firmware upgrade finished successfully.
[00140938][17 01] Firmware upgrade start...
[00209055][17 01] Firmware upgrade finished successfully.
[00209101][11 00] Firmware upgrade start...
[00257047][11 00] Firmware upgrade finished successfully.
[00257261][03 06] Firmware upgrade start...
[00561743][03 06] Firmware upgrade finished successfully.
[00561812][04 00] Firmware upgrade start...
[00619131][04 00] Firmware upgrade finished successfully.
[00619168]Done.

[00619204]Version checking[3]...
[00619290][03 05][00] v34.2.0.9 -> v34.2.0.9
[00619370][03 06][05] v2.2.6.19 -> v2.2.6.19
[00619412][04 00][05] v1.40.0.0 -> v1.40.0.0
[00619475][09 00][00] v1.7.0.3 -> v1.7.0.3
[00619590][11 00][05] v1.7.0.0 -> v1.7.0.0
[00619665][12 00][00] v1.8.0.0 -> v1.8.0.0
[00619740][12 01][00] v1.8.0.0 -> v1.8.0.0
[00619815][12 02][00] v1.8.0.0 -> v1.8.0.0
[00619904][12 03][00] v1.8.0.0 -> v1.8.0.0
[00619949][15 00][00] v1.1.2.0 -> v1.1.2.0
[00620015][17 00][05] v1.1.1.7 -> v1.1.1.7
[00620137][17 01][05] v1.0.2.7 -> v1.0.2.7
[00620194][19 00][00] v1.0.8.96 -> v1.0.8.96
[00620232][01 00][05] v1.20.3419 -> v1.20.3419
[00620268][01 01][05] v1.20.3419 -> v1.20.3419
[00620305]Packet upgrade finish successfully.



[00012259]========== remo-con disconnect. boot(15) ============
[00012294]Packet [C:\P3S_FW_V01.03.0020.bin] detected, card sn [0x80ce1834].
[00012334]Packet upgrade start...

[00012374]Packet checking...
[00012416]Packet vlink 01.03.0020 <-> 01.01.0009.
[00012454]Record vlink 01.03.0020 <-> 01.01.0009 (flow = 0).
[00012490]Done.

[00012532]Version checking[1]...
[00012604][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012684][03 06][00] v2.2.6.19 -> v2.2.6.19
[00012747][04 00][00] v1.40.0.0 -> v1.40.0.0
[00012807][09 00][00] v1.7.0.3 -> v1.7.0.3
[00012919][11 00][00] v1.7.0.0 -> v1.7.0.0
[00013016][12 00][00] v1.8.0.0 -> v1.8.0.0
[00013134][12 01][00] v1.8.0.0 -> v1.8.0.0
[00013215][12 02][00] v1.8.0.0 -> v1.8.0.0
[00013360][12 03][00] v1.8.0.0 -> v1.8.0.0
[00013404][15 00][00] v1.1.2.0 -> v1.1.2.0
[00013469][17 00][00] v1.1.1.7 -> v1.1.1.7
[00013673][17 01][00] v1.0.2.7 -> v1.0.2.7
[00013734][19 00][00] v1.0.8.96 -> v1.0.8.96
[00013773][01 00][00] v1.20.3419 -> v1.20.3419
[00013816][01 01][00] v1.20.3419 -> v1.20.3419
[00013855]Packet upgrade cancelled at version checking.



[00012621]========== 2015.08.05 20:00:51. boot(15) ============
[00012658]Packet [C:\P3S_FW_V01.03.0020.bin] detected, card sn [0x80ce1834].
[00012698]Packet upgrade start...

[00012741]Packet checking...
[00012782]Packet vlink 01.03.0020 <-> 01.01.0009.
[00012822]Record vlink 01.03.0020 <-> 01.01.0009 (flow = 0).
[00012861]Done.

[00012900]Version checking[1]...
[00012974][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013056][03 06][00] v2.2.6.19 -> v2.2.6.19
[00013101][04 00][00] v1.40.0.0 -> v1.40.0.0
[00013155][09 00][00] v1.7.0.3 -> v1.7.0.3
[00013276][11 00][00] v1.7.0.0 -> v1.7.0.0
[00013369][12 00][00] v1.8.0.0 -> v1.8.0.0
[00013469][12 01][00] v1.8.0.0 -> v1.8.0.0
[00013569][12 02][00] v1.8.0.0 -> v1.8.0.0
[00013669][12 03][00] v1.8.0.0 -> v1.8.0.0
[00013713][15 00][00] v1.1.2.0 -> v1.1.2.0
[00013800][17 00][00] v1.1.1.7 -> v1.1.1.7
[00013960][17 01][00] v1.0.2.7 -> v1.0.2.7
[00014014][19 00][00] v1.0.8.96 -> v1.0.8.96
[00014056][01 00][00] v1.20.3419 -> v1.20.3419
[00014095][01 01][00] v1.20.3419 -> v1.20.3419
[00014136]Packet upgrade cancelled at version checking.



[00012537]========== 2015.08.05 20:14:52. boot(15) ============
[00012576]Packet [C:\P3S_FW_V01.03.0020.bin] detected, card sn [0x80ce1834].
[00012614]Packet upgrade start...

[00012666]Packet checking...
[00012706]Packet vlink 01.03.0020 <-> 01.01.0009.
[00012752]Record vlink 01.03.0020 <-> 01.01.0009 (flow = 0).
[00012796]Done.

[00012835]Version checking[1]...
[00012901][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012981][03 06][00] v2.2.6.19 -> v2.2.6.19
[00013031][04 00][00] v1.40.0.0 -> v1.40.0.0
[00013096][09 00][00] v1.7.0.3 -> v1.7.0.3
[00013220][11 00][00] v1.6.0.0 -> v1.7.0.0 need upgrade.
[00013296][12 00][00] v1.8.0.0 -> v1.8.0.0
[00013496][12 01][00] v1.8.0.0 -> v1.8.0.0
[00013596][12 02][00] v1.8.0.0 -> v1.8.0.0
[00013696][12 03][00] v1.8.0.0 -> v1.8.0.0
[00013747][15 00][00] v1.1.2.0 -> v1.1.2.0
[00013830][17 00][00] v1.1.1.7 -> v1.1.1.7
[00013958][17 01][00] v1.0.2.7 -> v1.0.2.7
[00014015][19 00][00] v1.0.8.96 -> v1.0.8.96
[00014060][01 00][00] v1.20.3419 -> v1.20.3419
[00014100][01 01][00] v1.20.3419 -> v1.20.3419
[00014148]Done.

[00016191]Waiting for user confirm...
[00026232]Timeout, start upgrade automatically.

[00026318]Firmware upgrading[1]...
[00026373][11 00] Firmware upgrade start...
[00077060][11 00] Firmware upgrade finished successfully.
[00077097]Done.

[00077140]Version checking[2]...
[00077226][03 05][00] v34.2.0.9 -> v34.2.0.9
[00077305][03 06][00] v2.2.6.19 -> v2.2.6.19
[00077367][04 00][00] v1.40.0.0 -> v1.40.0.0
[00077418][09 00][00] v1.7.0.3 -> v1.7.0.3
[00077549][11 00][05] v1.7.0.0 -> v1.7.0.0
[00077639][12 00][00] v1.8.0.0 -> v1.8.0.0
[00077741][12 01][00] v1.8.0.0 -> v1.8.0.0
[00077843][12 02][00] v1.8.0.0 -> v1.8.0.0
[00077940][12 03][00] v1.8.0.0 -> v1.8.0.0
[00077983][15 00][00] v1.1.2.0 -> v1.1.2.0
[00078070][17 00][00] v1.1.1.7 -> v1.1.1.7
[00078199][17 01][00] v1.0.2.7 -> v1.0.2.7
[00078258][19 00][00] v1.0.8.96 -> v1.0.8.96
[00078299][01 00][00] v1.20.3419 -> v1.20.3419
[00078340][01 01][00] v1.20.3419 -> v1.20.3419
[00078389]Packet upgrade finish successfully.



[00012542]========== 2015.08.05 20:16:22. boot(15) ============
[00012582]Packet [C:\P3S_FW_V01.03.0020.bin] detected, card sn [0x80ce1834].
[00012626]Packet upgrade start...

[00012668]Packet checking...
[00012710]Packet vlink 01.03.0020 <-> 01.01.0009.
[00012755]Record vlink 01.03.0020 <-> 01.01.0009 (flow = 0).
[00012801]Done.

[00012840]Version checking[1]...
[00012916][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013016][03 06][00] v2.2.6.19 -> v2.2.6.19
[00013063][04 00][00] v1.40.0.0 -> v1.40.0.0
[00013111][09 00][00] v1.7.0.3 -> v1.7.0.3
[00013336][11 00][00] v1.7.0.0 -> v1.7.0.0
[00013431][12 00][00] v1.8.0.0 -> v1.8.0.0
[00013532][12 01][00] v1.8.0.0 -> v1.8.0.0
[00013632][12 02][00] v1.8.0.0 -> v1.8.0.0
[00013737][12 03][00] v1.8.0.0 -> v1.8.0.0
[00013783][15 00][00] v1.1.2.0 -> v1.1.2.0
[00013866][17 00][00] v1.1.1.7 -> v1.1.1.7
[00014005][17 01][00] v1.0.2.7 -> v1.0.2.7
[00014071][19 00][00] v1.0.8.96 -> v1.0.8.96
[00014112][01 00][00] v1.20.3419 -> v1.20.3419
[00014165][01 01][00] v1.20.3419 -> v1.20.3419
[00014203]Packet upgrade cancelled at version checking.



[00013595]========== remo-con disconnect. boot(15) ============
[00013642]Packet [C:\P3S_FW_V01.03.0020.bin] detected, card sn [0x80ce1834].
[00013681]Packet upgrade start...

[00013735]Packet checking...
[00013778]Packet vlink 01.03.0020 <-> 01.01.0009.
[00013827]Record vlink 01.03.0020 <-> 01.01.0009 (flow = 0).
[00013869]Done.

[00013910]Version checking[1]...
[00014000][03 05][00] v34.2.0.9 -> v34.2.0.9
[00014064][03 06][00] v2.2.6.19 -> v2.2.6.19
[00014110][04 00][00] v1.40.0.0 -> v1.40.0.0
[00014190][09 00][00] v1.7.0.3 -> v1.7.0.3
[00014301][11 00][00] v1.7.0.0 -> v1.7.0.0
[00014390][12 00][00] v1.8.0.0 -> v1.8.0.0
[00014480][12 01][00] v1.8.0.0 -> v1.8.0.0
[00014580][12 02][00] v1.8.0.0 -> v1.8.0.0
[00014680][12 03][00] v1.8.0.0 -> v1.8.0.0
[00014727][15 00][00] v1.1.2.0 -> v1.1.2.0
[00014810][17 00][00] v1.1.1.7 -> v1.1.1.7
[00014935][17 01][00] v1.0.2.7 -> v1.0.2.7
[00014990][19 00][00] v1.0.8.96 -> v1.0.8.96
[00015031][01 00][00] v1.20.3419 -> v1.20.3419
[00015071][01 01][00] v1.20.3419 -> v1.20.3419
[00015111]Packet upgrade cancelled at version checking.



[00013092]========== 2015.08.07 12:22:20. boot(15) ============
[00013139]Packet [C:\P3S_FW_V01.03.0020.bin] detected, card sn [0x80ce1834].
[00013178]Packet upgrade start...

[00013269]Packet checking...
[00013322]Packet vlink 01.03.0020 <-> 01.01.0009.
[00013364]Record vlink 01.03.0020 <-> 01.01.0009 (flow = 0).
[00013505]Done.

[00013549]Version checking[1]...
[00013641][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013731][03 06][00] v2.2.6.19 -> v2.2.6.19
[00013776][04 00][00] v1.40.0.0 -> v1.40.0.0
[00013855][09 00][00] v1.7.0.3 -> v1.7.0.3
[00013979][11 00][00] v1.7.0.0 -> v1.7.0.0
[00014081][12 00][00] v1.8.0.0 -> v1.8.0.0
[00014189][12 01][00] v1.8.0.0 -> v1.8.0.0
[00014294][12 02][00] v1.8.0.0 -> v1.8.0.0
[00014392][12 03][00] v1.8.0.0 -> v1.8.0.0
[00014437][15 00][00] v1.1.2.0 -> v1.1.2.0
[00014531][17 00][00] v1.1.1.7 -> v1.1.1.7
[00014645][17 01][00] v1.0.2.7 -> v1.0.2.7
[00014715][19 00][00] v1.0.8.96 -> v1.0.8.96
[00014759][01 00][00] v1.20.3419 -> v1.20.3419
[00014807][01 01][00] v1.20.3419 -> v1.20.3419
[00014850]Packet upgrade cancelled at version checking.



[00013898]========== 2015.08.07 14:43:54. boot(15) ============
[00014009]Packet [C:\P3S_FW_V01.03.0020.bin] detected, card sn [0x80ce1834].
[00014099]Packet upgrade start...

[00014235]Packet checking...
[00014380]Packet vlink 01.03.0020 <-> 01.01.0009.
[00014500]Record vlink 01.03.0020 <-> 01.01.0009 (flow = 0).
[00014615]Done.

[00014739]Version checking[1]...
[00014912][03 05][00] v34.2.0.9 -> v34.2.0.9
[00015030][03 06][00] v2.2.6.19 -> v2.2.6.19
[00015148][04 00][00] v1.40.0.0 -> v1.40.0.0
[00015278][09 00][00] v1.7.0.3 -> v1.7.0.3
[00015492][11 00][00] v1.7.0.0 -> v1.7.0.0
[00015654][12 00][00] v1.8.0.0 -> v1.8.0.0
[00015859][12 01][00] v1.8.0.0 -> v1.8.0.0
[00016040][12 02][00] v1.8.0.0 -> v1.8.0.0
[00016244][12 03][00] v1.8.0.0 -> v1.8.0.0
[00016319][15 00][00] v1.1.2.0 -> v1.1.2.0
[00016480][17 00][00] v1.1.1.7 -> v1.1.1.7
[00016699][17 01][00] v1.0.2.7 -> v1.0.2.7
[00016834][19 00][00] v1.0.8.96 -> v1.0.8.96
[00016947][01 00][00] v1.20.3419 -> v1.20.3419
[00017074][01 01][00] v1.20.3419 -> v1.20.3419
[00017194]Packet upgrade cancelled at version checking.



[00013933]========== 2015.08.07 21:45:29. boot(15) ============
[00014054]Packet [C:\P3S_FW_V01.03.0020.bin] detected, card sn [0x80ce1834].
[00014287]Packet upgrade start...

[00014446]Packet checking...
[00014569]Packet vlink 01.03.0020 <-> 01.01.0009.
[00014658]Record vlink 01.03.0020 <-> 01.01.0009 (flow = 0).
[00014754]Done.

[00014870]Version checking[1]...
[00015050][03 05][00] v34.2.0.9 -> v34.2.0.9
[00015207][03 06][00] v2.2.6.19 -> v2.2.6.19
[00015325][04 00][00] v1.40.0.0 -> v1.40.0.0
[00015455][09 00][00] v1.7.0.3 -> v1.7.0.3
[00015677][11 00][00] v1.7.0.0 -> v1.7.0.0
[00015902][12 00][00] v1.8.0.0 -> v1.8.0.0
[00016054][12 01][00] v1.8.0.0 -> v1.8.0.0
[00016236][12 02][00] v1.8.0.0 -> v1.8.0.0
[00016408][12 03][00] v1.8.0.0 -> v1.8.0.0
[00016529][15 00][00] v1.1.2.0 -> v1.1.2.0
[00016715][17 00][00] v1.1.1.7 -> v1.1.1.7
[00016920][17 01][00] v1.0.2.7 -> v1.0.2.7
[00017050][19 00][00] v1.0.8.96 -> v1.0.8.96
[00017140][01 00][00] v1.20.3419 -> v1.20.3419
[00017238][01 01][00] v1.20.3419 -> v1.20.3419
[00017354]Packet upgrade cancelled at version checking.



[00013144]========== remo-con disconnect. boot(15) ============
[00013185]Packet [C:\P3S_FW_V01.03.0020.bin] detected, card sn [0x80ce1834].
[00013231]Packet upgrade start...

[00013276]Packet checking...
[00013319]Packet vlink 01.03.0020 <-> 01.01.0009.
[00013363]Record vlink 01.03.0020 <-> 01.01.0009 (flow = 0).
[00013413]Done.

[00013455]Version checking[1]...
[00013532][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013612][03 06][00] v2.2.6.19 -> v2.2.6.19
[00013668][04 00][00] v1.40.0.0 -> v1.40.0.0
[00013727][09 00][00] v1.7.0.3 -> v1.7.0.3
[00013854][11 00][00] v1.7.0.0 -> v1.7.0.0
[00013947][12 00][00] v1.8.0.0 -> v1.8.0.0
[00014050][12 01][00] v1.8.0.0 -> v1.8.0.0
[00014148][12 02][00] v1.8.0.0 -> v1.8.0.0
[00014249][12 03][00] v1.8.0.0 -> v1.8.0.0
[00014294][15 00][00] v1.1.2.0 -> v1.1.2.0
[00014383][17 00][00] v1.1.1.7 -> v1.1.1.7
[00014529][17 01][00] v1.0.2.7 -> v1.0.2.7
[00014588][19 00][00] v1.0.8.96 -> v1.0.8.96
[00014640][01 00][00] v1.20.3419 -> v1.20.3419
[00014778][01 01][00] v1.20.3419 -> v1.20.3419
[00014823]Packet upgrade cancelled at version checking.



[00012691]========== 2015.08.08 19:37:05. boot(15) ============
[00012734]Packet [C:\P3S_FW_V01.03.0020.bin] detected, card sn [0x80ce1834].
[00012781]Packet upgrade start...

[00012838]Packet checking...
[00012886]Packet vlink 01.03.0020 <-> 01.01.0009.
[00012932]Record vlink 01.03.0020 <-> 01.01.0009 (flow = 0).
[00012984]Done.

[00013030]Version checking[1]...
[00013101][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013185][03 06][00] v2.2.6.19 -> v2.2.6.19
[00013238][04 00][00] v1.40.0.0 -> v1.40.0.0
[00013319][09 00][00] v1.7.0.3 -> v1.7.0.3
[00013441][11 00][00] v1.7.0.0 -> v1.7.0.0
[00013536][12 00][00] v1.8.0.0 -> v1.8.0.0
[00013624][12 01][00] v1.8.0.0 -> v1.8.0.0
[00013728][12 02][00] v1.8.0.0 -> v1.8.0.0
[00013820][12 03][00] v1.8.0.0 -> v1.8.0.0
[00013872][15 00][00] v1.1.2.0 -> v1.1.2.0
[00013971][17 00][00] v1.1.1.7 -> v1.1.1.7
[00014091][17 01][00] v1.0.2.7 -> v1.0.2.7
[00014176][19 00][00] v1.0.8.96 -> v1.0.8.96
[00014225][01 00][00] v1.20.3419 -> v1.20.3419
[00014271][01 01][00] v1.20.3419 -> v1.20.3419
[00014325]Packet upgrade cancelled at version checking.



[00013160]========== 2015.08.09 18:56:37. boot(15) ============
[00013205]Packet [C:\P3S_FW_V01.03.0020.bin] detected, card sn [0x80ce1834].
[00013250]Packet upgrade start...

[00013298]Packet checking...
[00013342]Packet vlink 01.03.0020 <-> 01.01.0009.
[00013394]Record vlink 01.03.0020 <-> 01.01.0009 (flow = 0).
[00013441]Done.

[00013485]Version checking[1]...
[00013567][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013648][03 06][00] v2.2.6.19 -> v2.2.6.19
[00013698][04 00][00] v1.40.0.0 -> v1.40.0.0
[00013763][09 00][00] v1.7.0.3 -> v1.7.0.3
[00013891][11 00][00] v1.7.0.0 -> v1.7.0.0
[00013983][12 00][00] v1.8.0.0 -> v1.8.0.0
[00014080][12 01][00] v1.8.0.0 -> v1.8.0.0
[00014182][12 02][00] v1.8.0.0 -> v1.8.0.0
[00014284][12 03][00] v1.8.0.0 -> v1.8.0.0
[00014427][15 00][00] v1.1.2.0 -> v1.1.2.0
[00014517][17 00][00] v1.1.1.7 -> v1.1.1.7
[00014657][17 01][00] v1.0.2.7 -> v1.0.2.7
[00014710][19 00][00] v1.0.8.96 -> v1.0.8.96
[00014760][01 00][00] v1.20.3419 -> v1.20.3419
[00014809][01 01][00] v1.20.3419 -> v1.20.3419
[00014858]Packet upgrade cancelled at version checking.



[00013774]========== 2015.08.29 12:06:46. boot(15) ============
[00013816]Packet [C:\P3S_FW_V01.03.0020.bin] detected, card sn [0x80ce1834].
[00013883]Packet upgrade start...

[00013936]Packet checking...
[00013988]Packet vlink 01.03.0020 <-> 01.01.0009.
[00014040]Record vlink 01.03.0020 <-> 01.01.0009 (flow = 0).
[00014088]Done.

[00014138]Version checking[1]...
[00014234][03 05][00] v34.2.0.9 -> v34.2.0.9
[00014313][03 06][00] v2.2.6.19 -> v2.2.6.19
[00014367][04 00][00] v1.40.0.0 -> v1.40.0.0
[00014427][09 00][00] v1.7.0.3 -> v1.7.0.3
[00014551][11 00][00] v1.7.0.0 -> v1.7.0.0
[00014648][12 00][00] v1.8.0.0 -> v1.8.0.0
[00014750][12 01][00] v1.8.0.0 -> v1.8.0.0
[00014845][12 02][00] v1.8.0.0 -> v1.8.0.0
[00014927][12 03][00] v1.8.0.0 -> v1.8.0.0
[00045482][15 00][00] device not detected.
[00045588][17 00][00] v1.1.1.7 -> v1.1.1.7
[00045726][17 01][00] v1.0.2.7 -> v1.0.2.7
[00045786][19 00][00] v1.0.8.96 -> v1.0.8.96
[00045851][01 00][00] v1.20.3419 -> v1.20.3419
[00045900][01 01][00] v1.20.3419 -> v1.20.3419
[00045945]Packet upgrade failed at version checking.



[00012562]========== 2015.08.29 12:07:50. boot(15) ============
[00012604]Packet [C:\P3S_FW_V01.03.0020.bin] detected, card sn [0x80ce1834].
[00012660]Packet upgrade start...

[00012708]Packet checking...
[00012761]Packet vlink 01.03.0020 <-> 01.01.0009.
[00012811]Record vlink 01.03.0020 <-> 01.01.0009 (flow = 0).
[00012861]Done.

[00012906]Version checking[1]...
[00013017][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013114][03 06][00] v2.2.6.19 -> v2.2.6.19
[00013180][04 00][00] v1.40.0.0 -> v1.40.0.0
[00013249][09 00][00] v1.7.0.3 -> v1.7.0.3
[00013476][11 00][00] v1.7.0.0 -> v1.7.0.0
[00013566][12 00][00] v1.8.0.0 -> v1.8.0.0
[00013669][12 01][00] v1.8.0.0 -> v1.8.0.0
[00013764][12 02][00] v1.8.0.0 -> v1.8.0.0
[00013867][12 03][00] v1.8.0.0 -> v1.8.0.0
[00013923][15 00][00] v1.1.2.0 -> v1.1.2.0
[00014025][17 00][00] v1.1.1.7 -> v1.1.1.7
[00014142][17 01][00] v1.0.2.7 -> v1.0.2.7
[00014218][19 00][00] v1.0.8.96 -> v1.0.8.96
[00014270][01 00][00] v1.20.3419 -> v1.20.3419
[00014327][01 01][00] v1.20.3419 -> v1.20.3419
[00014373]Packet upgrade cancelled at version checking.



[00012045]========== remo-con disconnect. boot(15) ============
[00012089]Packet [C:\P3S_FW_V01.04.0010.bin] detected, card sn [0x35f730ad].
[00012135]Packet upgrade start...

[00012186]Packet checking...
[00012234]Packet vlink 01.04.0010 <-> 01.03.0020.
[00012277]Record vlink 01.03.0020 <-> 01.01.0009 (flow = 0).
[00012323]Done.

[00012375]Version checking[1]...
[00012475][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012576][03 06][00] v2.2.6.19 -> v2.3.0.13 need upgrade.
[00012634][04 00][00] v1.40.0.0 -> v1.41.0.0 need upgrade.
[00012695][09 00][00] v1.7.0.3 -> v1.7.0.3
[00012835][11 00][00] v1.6.0.0 -> v1.7.0.0 need upgrade.
[00012930][12 00][00] v1.8.0.0 -> v1.10.0.0 need upgrade.
[00013029][12 01][00] v1.8.0.0 -> v1.10.0.0 need upgrade.
[00013130][12 02][00] v1.8.0.0 -> v1.10.0.0 need upgrade.
[00013230][12 03][00] v1.8.0.0 -> v1.10.0.0 need upgrade.
[00045777][15 00][00] device not detected.
[00045882][17 00][00] v1.1.1.7 -> v1.1.1.7
[00046022][17 01][00] v1.0.2.7 -> v1.0.2.7
[00046096][19 00][00] v1.0.8.96 -> v1.0.8.96
[00046141][01 00][00] v1.20.3419 -> v1.21.3647 need upgrade
[00046186][01 01][00] v1.20.3419 -> v1.21.3647 need upgrade
[00046237]Done.

[00048278]Waiting for user confirm...
[00058323]Timeout, start upgrade automatically.

[00058417]Firmware upgrading[1]...
[00072301][01 00] Firmware upgrade start...
[00011744][01 00] Firmware upgrade finished successfully.
[00011894]Done.

[00011937]Packet [C:\P3S_FW_V01.04.0010.bin] resumed, card sn [0x35f730ad].
[00011993]Packet vlink 01.04.0010 <-> 01.03.0020.
[00012039]Record vlink 01.03.0020 <-> 01.01.0009 (flow = 0).
[00012084]Version checking[2]...
[00012181][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012261][03 06][00] v2.2.6.19 -> v2.3.0.13 need upgrade.
[00012311][04 00][00] v1.40.0.0 -> v1.41.0.0 need upgrade.
[00012401][09 00][00] v1.7.0.3 -> v1.7.0.3
[00012522][11 00][00] v1.6.0.0 -> v1.7.0.0 need upgrade.
[00012635][12 00][00] v1.8.0.0 -> v1.10.0.0 need upgrade.
[00012736][12 01][00] v1.8.0.0 -> v1.10.0.0 need upgrade.
[00012835][12 02][00] v1.8.0.0 -> v1.10.0.0 need upgrade.
[00012935][12 03][00] v1.8.0.0 -> v1.10.0.0 need upgrade.
[00045483][15 00][00] device not detected.
[00045588][17 00][00] v1.1.1.7 -> v1.1.1.7
[00045727][17 01][00] v1.0.2.7 -> v1.0.2.7
[00045823][19 00][00] v1.0.8.96 -> v1.0.8.96
[00045873][01 00][05] v1.21.3647 -> v1.21.3647
[00045923][01 01][00] v1.20.3419 -> v1.21.3647 need upgrade
[00045969]Done.

[00046014]Firmware upgrading[2]...
[00046176][01 01] Firmware upgrade start...
[00076471][01 01] Firmware upgrade finished successfully.
[00076535][12 00] Firmware upgrade start...
[00143958][12 00] Firmware upgrade finished successfully.
[00144021][12 01] Firmware upgrade start...
[00217147][12 01] Firmware upgrade finished successfully.
[00217214][12 02] Firmware upgrade start...
[00290179][12 02] Firmware upgrade finished successfully.
[00290243][12 03] Firmware upgrade start...
[00364481][12 03] Firmware upgrade finished successfully.
[00364542][11 00] Firmware upgrade start...
[00414198][11 00] Firmware upgrade finished successfully.
[00414452][03 06] Firmware upgrade start...
[00755434][03 06] Firmware upgrade finished successfully.
[00755509][04 00] Firmware upgrade start...
[00813807][04 00] Firmware upgrade finished successfully.
[00813862]Done.

[00813905]Version checking[3]...
[00813994][03 05][00] v34.2.0.9 -> v34.2.0.9
[00814161][03 06][05] v2.3.0.13 -> v2.3.0.13
[00814212][04 00][05] v1.41.0.0 -> v1.41.0.0
[00814282][09 00][00] v1.7.0.3 -> v1.7.0.3
[00814432][11 00][05] v1.7.0.0 -> v1.7.0.0
[00814532][12 00][05] v1.10.0.0 -> v1.10.0.0
[00814623][12 01][05] v1.10.0.0 -> v1.10.0.0
[00814732][12 02][05] v1.10.0.0 -> v1.10.0.0
[00814846][12 03][05] v1.10.0.0 -> v1.10.0.0
[00847398][15 00][00] device not detected.
[00847484][17 00][00] v1.1.1.7 -> v1.1.1.7
[00847624][17 01][00] v1.0.2.7 -> v1.0.2.7
[00847684][19 00][00] v1.0.8.96 -> v1.0.8.96
[00847736][01 00][05] v1.21.3647 -> v1.21.3647
[00847783][01 01][05] v1.21.3647 -> v1.21.3647
[00847830]Packet upgrade failed at version checking.



[00012233]========== remo-con disconnect. boot(15) ============
[00012284]Packet [C:\P3S_FW_V01.04.0010.bin] detected, card sn [0x80ce1834].
[00012344]Packet upgrade start...

[00012402]Packet checking...
[00012451]Packet vlink 01.04.0010 <-> 01.03.0020.
[00012510]Record vlink 01.03.0020 <-> 01.01.0009 (flow = 0).
[00012568]Done.

[00012617]Version checking[1]...
[00012704][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012804][03 06][00] v2.3.0.13 -> v2.3.0.13
[00012865][04 00][00] v1.41.0.0 -> v1.41.0.0
[00012931][09 00][00] v1.7.0.3 -> v1.7.0.3
[00013204][11 00][00] v1.7.0.0 -> v1.7.0.0
[00013292][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013392][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013492][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013592][12 03][00] v1.10.0.0 -> v1.10.0.0
[00046146][15 00][00] device not detected.
[00046254][17 00][00] v1.1.1.7 -> v1.1.1.7
[00046399][17 01][00] v1.0.2.7 -> v1.0.2.7
[00046469][19 00][00] v1.0.8.96 -> v1.0.8.96
[00046518][01 00][00] v1.21.3647 -> v1.21.3647
[00046580][01 01][00] v1.21.3647 -> v1.21.3647
[00046634]Packet upgrade failed at version checking.



[00014746]========== remo-con disconnect. boot(15) ============
[00014800]Packet [C:\P3S_FW_V01.04.0010.bin] detected, card sn [0x80ce1834].
[00014856]Packet upgrade start...

[00015008]Packet checking...
[00015063]Packet vlink 01.04.0010 <-> 01.03.0020.
[00015117]Record vlink 01.03.0020 <-> 01.01.0009 (flow = 0).
[00015177]Done.

[00015230]Version checking[1]...
[00015310][03 05][00] v34.2.0.9 -> v34.2.0.9
[00015414][03 06][00] v2.3.0.13 -> v2.3.0.13
[00015473][04 00][00] v1.41.0.0 -> v1.41.0.0
[00015563][09 00][00] v1.7.0.3 -> v1.7.0.3
[00015690][11 00][00] v1.7.0.0 -> v1.7.0.0
[00015804][12 00][00] v1.10.0.0 -> v1.10.0.0
[00015904][12 01][00] v1.10.0.0 -> v1.10.0.0
[00016004][12 02][00] v1.10.0.0 -> v1.10.0.0
[00016104][12 03][00] v1.10.0.0 -> v1.10.0.0
[00048658][15 00][00] device not detected.
[00048763][17 00][00] v1.1.1.7 -> v1.1.1.7
[00048911][17 01][00] v1.0.2.7 -> v1.0.2.7
[00048981][19 00][00] v1.0.8.96 -> v1.0.8.96
[00049039][01 00][00] v1.21.3647 -> v1.21.3647
[00049091][01 01][00] v1.21.3647 -> v1.21.3647
[00049143]Packet upgrade failed at version checking.



[00012182]========== remo-con disconnect. boot(15) ============
[00012232]Packet [C:\P3S_FW_V01.04.0010.bin] detected, card sn [0x35f730ad].
[00012285]Packet upgrade start...

[00012337]Packet checking...
[00012386]Packet vlink 01.04.0010 <-> 01.03.0020.
[00012442]Record vlink 01.03.0020 <-> 01.01.0009 (flow = 0).
[00012489]Done.

[00012540]Version checking[1]...
[00012622][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012702][03 06][00] v2.3.0.13 -> v2.3.0.13
[00012777][04 00][00] v1.41.0.0 -> v1.41.0.0
[00012851][09 00][00] v1.7.0.3 -> v1.7.0.3
[00012962][11 00][00] v1.7.0.0 -> v1.7.0.0
[00013048][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013163][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013247][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013337][12 03][00] v1.10.0.0 -> v1.10.0.0
[00045888][15 00][00] device not detected.
[00045989][17 00][00] v1.1.1.7 -> v1.1.1.7
[00046119][17 01][00] v1.0.2.7 -> v1.0.2.7
[00046194][19 00][00] v1.0.8.96 -> v1.0.8.96
[00046242][01 00][00] v1.21.3647 -> v1.21.3647
[00046290][01 01][00] v1.21.3647 -> v1.21.3647
[00046428]Packet upgrade failed at version checking.



[00012182]========== remo-con disconnect. boot(15) ============
[00012261]Packet [C:\P3S_FW_V01.04.0010.bin] detected, card sn [0x35f730ad].
[00012318]Packet upgrade start...

[00012372]Packet checking...
[00012422]Packet vlink 01.04.0010 <-> 01.03.0020.
[00012475]Record vlink 01.03.0020 <-> 01.01.0009 (flow = 0).
[00012528]Done.

[00012581]Version checking[1]...
[00012658][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012740][03 06][00] v2.3.0.13 -> v2.3.0.13
[00012790][04 00][00] v1.41.0.0 -> v1.41.0.0
[00012867][09 00][00] v1.7.0.3 -> v1.7.0.3
[00013004][11 00][00] v1.7.0.0 -> v1.7.0.0
[00013093][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013212][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013312][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013413][12 03][00] v1.10.0.0 -> v1.10.0.0
[00013467][15 00][00] v1.1.2.0 -> v1.1.2.0
[00013563][17 00][00] v1.1.1.7 -> v1.1.1.7
[00013683][17 01][00] v1.0.2.7 -> v1.0.2.7
[00013768][19 00][00] v1.0.8.96 -> v1.0.8.96
[00013821][01 00][00] v1.21.3647 -> v1.21.3647
[00013873][01 01][00] v1.21.3647 -> v1.21.3647
[00013923]Packet upgrade cancelled at version checking.



[00012164]========== remo-con disconnect. boot(15) ============
[00012220]Packet [C:\P3S_FW_V01.04.0010.bin] detected, card sn [0x35f730ad].
[00012267]Packet upgrade start...

[00012328]Packet checking...
[00012381]Packet vlink 01.04.0010 <-> 01.03.0020.
[00012433]Record vlink 01.04.0010 <-> 01.03.0020 (flow = 0).
[00012486]Done.

[00012544]Version checking[1]...
[00012628][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012714][03 06][00] v2.3.0.13 -> v2.3.0.13
[00012783][04 00][00] v1.41.0.0 -> v1.41.0.0
[00012843][09 00][00] v1.7.0.3 -> v1.7.0.3
[00012969][11 00][00] v1.7.0.0 -> v1.7.0.0
[00013069][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013177][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013278][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013402][12 03][00] v1.10.0.0 -> v1.10.0.0
[00022461][15 00][00] v1.1.2.0 -> v1.1.2.0
[00022657][17 00][00] v1.1.1.7 -> v1.1.1.7
[00022833][17 01][00] v1.0.2.7 -> v1.0.2.7
[00022902][19 00][00] v1.0.8.96 -> v1.0.8.96
[00022961][01 00][00] v1.21.3647 -> v1.21.3647
[00023007][01 01][00] v1.21.3647 -> v1.21.3647
[00023064]Packet upgrade cancelled at version checking.



[00012196]========== remo-con disconnect. boot(15) ============
[00012253]Packet [C:\P3S_FW_V01.03.0020.bin] detected, card sn [0x35f730ad].
[00012303]Packet upgrade start...

[00012363]Packet checking...
[00012424]Packet vlink 01.03.0020 <-> 01.01.0009.
[00012564]Record vlink 01.04.0010 <-> 01.03.0020 (flow = 1).
[00012650]Done.

[00012695]Version checking[1]...
[00012801][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012901][03 06][00] v2.3.0.13 -> v2.2.6.19 need upgrade.
[00012973][04 00][00] v1.41.0.0 -> v1.40.0.0 need upgrade.
[00013045][09 00][00] v1.7.0.3 -> v1.7.0.3
[00013186][11 00][00] v1.7.0.0 -> v1.7.0.0
[00013295][12 00][00] v1.10.0.0 -> v1.8.0.0
[00013415][12 01][00] v1.10.0.0 -> v1.8.0.0
[00013515][12 02][00] v1.10.0.0 -> v1.8.0.0
[00013616][12 03][00] v1.10.0.0 -> v1.8.0.0
[00046165][15 00][00] device not detected.
[00046271][17 00][00] v1.1.1.7 -> v1.1.1.7
[00046415][17 01][00] v1.0.2.7 -> v1.0.2.7
[00046486][19 00][00] v1.0.8.96 -> v1.0.8.96
[00046537][01 00][00] v1.21.3647 -> v1.20.3419 need upgrade
[00046592][01 01][00] v1.21.3647 -> v1.20.3419 need upgrade
[00046650]Done.

[00048695]Waiting for user confirm...
[00058760]Timeout, start upgrade automatically.

[00058867]Firmware upgrading[1]...
[00059031][01 01] Firmware upgrade start...
[00089312][01 01] Firmware upgrade finished successfully.
[00089550][03 06] Firmware upgrade start...
[00392072][03 06] Firmware upgrade finished successfully.
[00392157][04 00] Firmware upgrade start...
[00450101][04 00] Firmware upgrade finished successfully.
[00450160]Done.

[00450209]Version checking[2]...
[00450296][03 05][00] v34.2.0.9 -> v34.2.0.9
[00450396][03 06][05] v2.2.6.19 -> v2.2.6.19
[00450558][04 00][05] v1.40.0.0 -> v1.40.0.0
[00450626][09 00][00] v1.7.0.3 -> v1.7.0.3
[00450755][11 00][00] v1.7.0.0 -> v1.7.0.0
[00450852][12 00][00] v1.10.0.0 -> v1.8.0.0
[00450952][12 01][00] v1.10.0.0 -> v1.8.0.0
[00451052][12 02][00] v1.10.0.0 -> v1.8.0.0
[00451153][12 03][00] v1.10.0.0 -> v1.8.0.0
[00483702][15 00][00] device not detected.
[00483829][17 00][00] v1.1.1.7 -> v1.1.1.7
[00483968][17 01][00] v1.0.2.7 -> v1.0.2.7
[00484048][19 00][00] v1.0.8.96 -> v1.0.8.96
[00484102][01 00][00] v1.21.3647 -> v1.20.3419 need upgrade
[00484157][01 01][05] v1.20.3419 -> v1.20.3419
[00484215]Packet upgrade failed at version checking.



[00012302]========== remo-con disconnect. boot(15) ============
[00012354]Packet [C:\P3S_FW_V01.04.0010.bin] detected, card sn [0x35f730ad].
[00012407]Packet upgrade start...

[00012465]Packet checking...
[00012521]Packet vlink 01.04.0010 <-> 01.03.0020.
[00012575]Record vlink 01.04.0010 <-> 01.03.0020 (flow = 0).
[00012630]Done.

[00012686]Version checking[1]...
[00012797][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012897][03 06][00] v2.2.6.19 -> v2.3.0.13 need upgrade.
[00012963][04 00][00] v1.40.0.0 -> v1.41.0.0 need upgrade.
[00013032][09 00][00] v1.7.0.3 -> v1.7.0.3
[00013169][11 00][00] v1.7.0.0 -> v1.7.0.0
[00013273][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013372][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013472][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013572][12 03][00] v1.10.0.0 -> v1.10.0.0
[00046126][15 00][00] device not detected.
[00046249][17 00][00] v1.1.1.7 -> v1.1.1.7
[00046389][17 01][00] v1.0.2.7 -> v1.0.2.7
[00046454][19 00][00] v1.0.8.96 -> v1.0.8.96
[00046508][01 00][00] v1.21.3647 -> v1.21.3647
[00046568][01 01][00] v1.20.3419 -> v1.21.3647 need upgrade
[00046616]Done.

[00048670]Waiting for user confirm...
[00058723]Timeout, start upgrade automatically.

[00058829]Firmware upgrading[1]...
[00058998][01 01] Firmware upgrade start...
[00089287][01 01] Firmware upgrade finished successfully.
[00089630][03 06] Firmware upgrade start...
[00421413][03 06] Firmware upgrade finished successfully.
[00421494][04 00] Firmware upgrade start...
[00479996][04 00] Firmware upgrade finished successfully.
[00480055]Done.

[00480109]Version checking[2]...
[00480206][03 05][00] v34.2.0.9 -> v34.2.0.9
[00480306][03 06][05] v2.3.0.13 -> v2.3.0.13
[00480380][04 00][05] v1.41.0.0 -> v1.41.0.0
[00480455][09 00][00] v1.7.0.3 -> v1.7.0.3
[00480587][11 00][00] v1.7.0.0 -> v1.7.0.0
[00480697][12 00][00] v1.10.0.0 -> v1.10.0.0
[00480821][12 01][00] v1.10.0.0 -> v1.10.0.0
[00480921][12 02][00] v1.10.0.0 -> v1.10.0.0
[00481041][12 03][00] v1.10.0.0 -> v1.10.0.0
[00513593][15 00][00] device not detected.
[00513697][17 00][00] v1.1.1.7 -> v1.1.1.7
[00513857][17 01][00] v1.0.2.7 -> v1.0.2.7
[00513937][19 00][00] v1.0.8.96 -> v1.0.8.96
[00513988][01 00][00] v1.21.3647 -> v1.21.3647
[00514049][01 01][05] v1.21.3647 -> v1.21.3647
[00514103]Packet upgrade failed at version checking.



[00013245]========== remo-con disconnect. boot(15) ============
[00013301]Packet [C:\P3S_FW_V01.04.0010.bin] detected, card sn [0x35f730ad].
[00013357]Packet upgrade start...

[00013411]Packet checking...
[00013471]Packet vlink 01.04.0010 <-> 01.03.0020.
[00013526]Record vlink 01.04.0010 <-> 01.03.0020 (flow = 0).
[00013578]Done.

[00013636]Version checking[1]...
[00013740][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013840][03 06][00] v2.3.0.13 -> v2.3.0.13
[00013902][04 00][00] v1.41.0.0 -> v1.41.0.0
[00013974][09 00][00] v1.7.0.3 -> v1.7.0.3
[00014100][11 00][00] v1.7.0.0 -> v1.7.0.0
[00014217][12 00][00] v1.10.0.0 -> v1.10.0.0
[00014334][12 01][00] v1.10.0.0 -> v1.10.0.0
[00014434][12 02][00] v1.10.0.0 -> v1.10.0.0
[00014561][12 03][00] v1.10.0.0 -> v1.10.0.0
[00047125][15 00][00] device not detected.
[00047231][17 00][00] v1.1.1.7 -> v1.1.1.7
[00047371][17 01][00] v1.0.2.7 -> v1.0.2.7
[00047436][19 00][00] v1.0.8.96 -> v1.0.8.96
[00047496][01 00][00] v1.21.3647 -> v1.21.3647
[00047650][01 01][00] v1.21.3647 -> v1.21.3647
[00047704]Packet upgrade failed at version checking.



[00013118]========== remo-con disconnect. boot(15) ============
[00013176]Packet [C:\P3S_FW_V01.04.0010.bin] detected, card sn [0x35f730ad].
[00013231]Packet upgrade start...

[00013290]Packet checking...
[00013345]Packet vlink 01.04.0010 <-> 01.03.0020.
[00013398]Record vlink 01.04.0010 <-> 01.03.0020 (flow = 0).
[00013455]Done.

[00013509]Version checking[1]...
[00013618][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013719][03 06][00] v2.3.0.13 -> v2.3.0.13
[00013794][04 00][00] v1.41.0.0 -> v1.41.0.0
[00013885][09 00][00] v1.7.0.3 -> v1.7.0.3
[00014019][11 00][00] v1.7.0.0 -> v1.7.0.0
[00014106][12 00][00] v1.10.0.0 -> v1.10.0.0
[00014231][12 01][00] v1.10.0.0 -> v1.10.0.0
[00014331][12 02][00] v1.10.0.0 -> v1.10.0.0
[00014431][12 03][00] v1.10.0.0 -> v1.10.0.0
[00047023][15 00][00] device not detected.
[00047128][17 00][00] v1.1.1.7 -> v1.1.1.7
[00047268][17 01][00] v1.0.2.7 -> v1.0.2.7
[00047366][19 00][00] v1.0.8.96 -> v1.0.8.96
[00047423][01 00][00] v1.21.3647 -> v1.21.3647
[00047472][01 01][00] v1.21.3647 -> v1.21.3647
[00047534]Packet upgrade failed at version checking.



[00013235]========== remo-con disconnect. boot(15) ============
[00013292]Packet [C:\P3S_FW_V01.04.0010.bin] detected, card sn [0x80ce1834].
[00013359]Packet upgrade start...

[00013424]Packet checking...
[00013491]Packet vlink 01.04.0010 <-> 01.03.0020.
[00013553]Record vlink 01.04.0010 <-> 01.03.0020 (flow = 0).
[00013610]Done.

[00013674]Version checking[1]...
[00013774][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013878][03 06][00] v2.3.0.13 -> v2.3.0.13
[00013954][04 00][00] v1.41.0.0 -> v1.41.0.0
[00014042][09 00][00] v1.7.0.3 -> v1.7.0.3
[00014174][11 00][00] v1.7.0.0 -> v1.7.0.0
[00014291][12 00][00] v1.10.0.0 -> v1.10.0.0
[00014412][12 01][00] v1.10.0.0 -> v1.10.0.0
[00014503][12 02][00] v1.10.0.0 -> v1.10.0.0
[00014703][12 03][00] v1.10.0.0 -> v1.10.0.0
[00019265][15 00][00] v1.1.2.0 -> v1.1.2.0
[00019382][17 00][00] v1.1.1.7 -> v1.1.1.7
[00019522][17 01][00] v1.0.2.7 -> v1.0.2.7
[00019602][19 00][00] v1.0.8.96 -> v1.0.8.96
[00019669][01 00][00] v1.21.3647 -> v1.21.3647
[00019733][01 01][00] v1.21.3647 -> v1.21.3647
[00019795]Packet upgrade cancelled at version checking.



[00012252]========== 2015.09.07 11:58:24. boot(15) ============
[00012317]Packet [C:\P3S_FW_V01.04.0010.bin] detected, card sn [0x80ce1834].
[00012380]Packet upgrade start...

[00012446]Packet checking...
[00012516]Packet vlink 01.04.0010 <-> 01.03.0020.
[00012580]Record vlink 01.04.0010 <-> 01.03.0020 (flow = 0).
[00012648]Done.

[00012709]Version checking[1]...
[00012811][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012913][03 06][00] v2.3.0.13 -> v2.3.0.13
[00012989][04 00][00] v1.41.0.0 -> v1.41.0.0
[00013073][09 00][00] v1.7.0.3 -> v1.7.0.3
[00013234][11 00][00] v1.7.0.0 -> v1.7.0.0
[00013339][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013448][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013556][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013656][12 03][00] v1.10.0.0 -> v1.10.0.0
[00041520][15 00][00] v1.1.2.0 -> v1.1.2.0
[00041615][17 00][00] v1.1.1.7 -> v1.1.1.7
[00041782][17 01][00] v1.0.2.7 -> v1.0.2.7
[00041879][19 00][00] v1.0.8.96 -> v1.0.8.96
[00041942][01 00][00] v1.21.3647 -> v1.21.3647
[00042011][01 01][00] v1.21.3647 -> v1.21.3647
[00042072]Packet upgrade cancelled at version checking.



[00012793]========== 2015.09.07 13:45:44. boot(15) ============
[00012863]Packet [C:\P3S_FW_V01.04.0010.bin] detected, card sn [0x80ce1834].
[00012924]Packet upgrade start...

[00013001]Packet checking...
[00013063]Packet vlink 01.04.0010 <-> 01.03.0020.
[00013124]Record vlink 01.04.0010 <-> 01.03.0020 (flow = 0).
[00013192]Done.

[00013258]Version checking[1]...
[00013363][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013464][03 06][00] v2.3.0.13 -> v2.3.0.13
[00013533][04 00][00] v1.41.0.0 -> v1.41.0.0
[00013723][09 00][00] v1.7.0.3 -> v1.7.0.3
[00013888][11 00][00] v1.7.0.0 -> v1.7.0.0
[00014008][12 00][00] v1.10.0.0 -> v1.10.0.0
[00014111][12 01][00] v1.10.0.0 -> v1.10.0.0
[00014232][12 02][00] v1.10.0.0 -> v1.10.0.0
[00014332][12 03][00] v1.10.0.0 -> v1.10.0.0
[00014406][15 00][00] v1.1.2.0 -> v1.1.2.0
[00014507][17 00][00] v1.1.1.7 -> v1.1.1.7
[00014667][17 01][00] v1.0.2.7 -> v1.0.2.7
[00014741][19 00][00] v1.0.8.96 -> v1.0.8.96
[00014798][01 00][00] v1.21.3647 -> v1.21.3647
[00014865][01 01][00] v1.21.3647 -> v1.21.3647
[00014926]Packet upgrade cancelled at version checking.



[00012787]========== 2015.09.07 13:47:27. boot(0) ============
[00012857]Packet [C:\P3S_FW_V01.04.0010.bin] detected, card sn [0x80ce1834].
[00012919]Packet upgrade start...

[00012993]Packet checking...
[00013071]Packet vlink 01.04.0010 <-> 01.03.0020.
[00013143]Record vlink 01.04.0010 <-> 01.03.0020 (flow = 0).
[00013199]Done.

[00013259]Version checking[1]...
[00013353][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013453][03 06][00] v2.3.0.13 -> v2.3.0.13
[00013527][04 00][00] v1.41.0.0 -> v1.41.0.0
[00013605][09 00][00] v1.7.0.3 -> v1.7.0.3
[00013752][11 00][00] v1.7.0.0 -> v1.7.0.0
[00013885][12 00][00] v1.10.0.0 -> v1.10.0.0
[00014006][12 01][00] v1.10.0.0 -> v1.10.0.0
[00014110][12 02][00] v1.10.0.0 -> v1.10.0.0
[00014223][12 03][00] v1.10.0.0 -> v1.10.0.0
[00014289][15 00][00] v1.1.2.0 -> v1.1.2.0
[00014397][17 00][00] v1.1.1.7 -> v1.1.1.7
[00014541][17 01][00] v1.0.2.7 -> v1.0.2.7
[00014626][19 00][00] v1.0.8.96 -> v1.0.8.96
[00014694][01 00][00] v1.21.3647 -> v1.21.3647
[00014758][01 01][00] v1.21.3647 -> v1.21.3647
[00014827]Packet upgrade cancelled at version checking.



[00013343]========== remo-con disconnect. boot(15) ============
[00013400]Packet [C:\P3S_FW_V01.04.0010.bin] detected, card sn [0x80ce1834].
[00013460]Packet upgrade start...

[00013523]Packet checking...
[00013581]Packet vlink 01.04.0010 <-> 01.03.0020.
[00013722]Record vlink 01.04.0010 <-> 01.03.0020 (flow = 0).
[00013780]Done.

[00013843]Version checking[1]...
[00013939][03 05][00] v34.2.0.9 -> v34.2.0.9
[00014039][03 06][00] v2.3.0.13 -> v2.3.0.13
[00014103][04 00][00] v1.41.0.0 -> v1.41.0.0
[00014188][09 00][00] v1.7.0.3 -> v1.7.0.3
[00014318][11 00][00] v1.7.0.0 -> v1.7.0.0
[00014412][12 00][00] v1.10.0.0 -> v1.10.0.0
[00014508][12 01][00] v1.10.0.0 -> v1.10.0.0
[00014612][12 02][00] v1.10.0.0 -> v1.10.0.0
[00014712][12 03][00] v1.10.0.0 -> v1.10.0.0
[00014776][15 00][00] v1.1.2.0 -> v1.1.2.0
[00014889][17 00][00] v1.1.1.7 -> v1.1.1.7
[00015028][17 01][00] v1.0.2.7 -> v1.0.2.7
[00015107][19 00][00] v1.0.8.96 -> v1.0.8.96
[00015169][01 00][00] v1.21.3647 -> v1.21.3647
[00015229][01 01][00] v1.21.3647 -> v1.21.3647
[00015289]Packet upgrade cancelled at version checking.

paul@alphacrust Posted at 2015-9-7 21:03
What's the Air End USB transmit ?

I've posted a video to: http://www.alphacrust.co.uk/videos/IMG_03 ...

Try a downgrade to 1.3.20, see what the logs say then..

Rigworker Posted at 2015-9-7 22:37
Hey splooge, is there a post or document that tells what piece of equipment each of those upgrade  ...

Tada..

01 00 Camera
03 06 Main Control
04 00 Gimbal
05 00 Center Board
08 00 Air encoder  
09 00 OFDM Air End OFDM
11 00 Battery
12 00/01/02/03 M1/M2/M3/M4 ESC
15 00 Air End USB transmit
17 00/01 Vision position system
19 00 Air base band

christopherhyzy Posted at 2015-9-7 22:42
i had the same issue this morning, i tried everything from reformatting the card, switching out batt ...

This looks like it has updated OK..

Check the "About" section in the App and see what it says

Aircraft should be 1.4.0010
RC should be 1.3.20
App should be  2.2.0 IOS/2.1.0 Android

Looks OK though and if it powers on and "seems" ok, then it is

sploodge Posted at 2015-9-7 17:51
This looks like it has updated OK..

Check the "About" section in the App and see what it says

My RC is refusing to upgrade. My OS is Android.

App: 2.1.0
Remote Controller: 1.2.7
Firmware: 1.4.10

DJI inconsistently adds leading zeros to version numbers so I assume 1.4.10 is the same as 1.4.0010. But yeah you can see that everything is up to date except the remote. And it actually wouldn't let me fly the drone now, it says it requires an update. I put the bin on the flash drive, I put it into the RC, I power the RC up, nothing happens, it just stays there showing me solid red. I tried it a few times and it finally started beeping like crazy after just being on like this for a while. And then it proceeded to beep for a long time. After a while I finally powered it down. The status file stated the operation was aborted because the version of the file was the same or lower than the current version on the RC. Which is obviously false.

michael@kuzmin. Posted at 2015-9-8 00:21
My RC is refusing to upgrade. My OS is Android.

App: 2.1.0

You need to update your controller to 1.3.2. which was the last update and there is no controller update required for 1.4.0

sploodge Posted at 2015-9-7 15:46
Tada..

01 00 Camera

Thanks Splooge. That is pretty much all of them.

I just updated mine, when it was done. all lights went red. Log said update failed. When I went to try and update again the thing just beeps....keeps beeping! loudly and constantly. Then it started to do what looked like the normal firmware update process and has been blinking yellow for almost 45 min. Not really sure what to do.

I don't know whether this matters, I have mistakenly used the firmware image for P3 Pro for my P3 Advanced RC upgrade (to 1.3.20). Is there is a way to re-apply the same upgrade using the firmware image for P3 Advanced?

Thanks,

tongtang878 Posted at 2015-9-8 04:55
I don't know whether this matters, I have mistakenly used the firmware image for P3 Pro for my P3 Ad ...

Replied in another thread. The firmware file for both Pro and Advanced seem to contain the same update for the RC..

Having same issue with firmware!! Help!



:@:@
[00012508]========== 2015.09.07 14:43:05. boot(15) ============
[00012549]Packet [C:\P3X_FW_V01.04.0010.bin] detected, card sn [0xb0ce292d].
[00012591]Packet upgrade start...

[00012637]Packet checking...
[00012678]Packet vlink 01.04.0010 <-> 01.03.0020.
[00012720]Record vlink 01.04.0010 <-> 01.03.0020 (flow = 0).
[00012762]Done.

[00012802]Version checking[1]...
[00012887][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012966][03 06][00] v2.3.0.13 -> v2.3.0.13
[00013010][04 00][00] v1.41.0.0 -> v1.41.0.0
[00013092][09 00][00] v1.7.0.3 -> v1.7.0.3
[00013209][11 00][00] v1.7.0.0 -> v1.7.0.0
[00013395][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013498][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013593][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013698][12 03][00] v1.10.0.0 -> v1.10.0.0
[00013864][15 00][00] v1.1.2.0 -> v1.1.2.0
[00013956][17 00][00] v1.1.1.7 -> v1.1.1.7
[00014075][17 01][00] v1.0.2.7 -> v1.0.2.7
[00014140][19 00][00] v1.0.8.96 -> v1.0.8.96
[00014181][01 00][00] v1.23.3419 -> v1.23.3419
[00014231][01 01][00] v1.23.3419 -> v1.23.3419
[00014295][08 00][00] v0.12.0.4 -> v0.12.0.4
[00014337]Packet upgrade cancelled at version checking.



[00013872]========== remo-con disconnect. boot(15) ============
[00013915]Packet [C:\P3X_FW_V01.04.0010.bin] detected, card sn [0xb0ce292d].
[00013959]Packet upgrade start...

[00014006]Packet checking...
[00014055]Packet vlink 01.04.0010 <-> 01.03.0020.
[00014096]Record vlink 01.04.0010 <-> 01.03.0020 (flow = 0).
[00014138]Done.

[00014180]Version checking[1]...
[00014266][03 05][00] v34.2.0.9 -> v34.2.0.9
[00014346][03 06][00] v2.3.0.13 -> v2.3.0.13
[00014400][04 00][00] v1.41.0.0 -> v1.41.0.0
[00014465][09 00][00] v1.7.0.3 -> v1.7.0.3
[00014590][11 00][00] v1.7.0.0 -> v1.7.0.0
[00014679][12 00][00] v1.10.0.0 -> v1.10.0.0
[00014779][12 01][00] v1.10.0.0 -> v1.10.0.0
[00014879][12 02][00] v1.10.0.0 -> v1.10.0.0
[00014978][12 03][00] v1.10.0.0 -> v1.10.0.0
[00015132][15 00][00] v1.1.2.0 -> v1.1.2.0
[00015220][17 00][00] v1.1.1.7 -> v1.1.1.7
[00015358][17 01][00] v1.0.2.7 -> v1.0.2.7
[00015424][19 00][00] v1.0.8.96 -> v1.0.8.96
[00015466][01 00][00] v1.23.3419 -> v1.23.3419
[00015507][01 01][00] v1.23.3419 -> v1.23.3419
[00015574][08 00][00] v0.12.0.4 -> v0.12.0.4
[00015614]Packet upgrade cancelled at version checking.



[00013454]========== 2015.09.07 14:57:41. boot(15) ============
[00013498]Packet [C:\P3X_FW_V01.04.0010.bin] detected, card sn [0xb0ce292d].
[00013541]Packet upgrade start...

[00013589]Packet checking...
[00013632]Packet vlink 01.04.0010 <-> 01.03.0020.
[00013766]Record vlink 01.04.0010 <-> 01.03.0020 (flow = 0).
[00013807]Done.

[00013856]Version checking[1]...
[00013935][03 05][00] v34.2.0.9 -> v34.2.0.9
[00014024][03 06][00] v2.3.0.13 -> v2.3.0.13
[00014072][04 00][00] v1.41.0.0 -> v1.41.0.0
[00014158][09 00][00] v1.7.0.3 -> v1.7.0.3
[00014273][11 00][00] v1.7.0.0 -> v1.7.0.0
[00014401][12 00][00] v1.10.0.0 -> v1.10.0.0
[00014481][12 01][00] v1.10.0.0 -> v1.10.0.0
[00014581][12 02][00] v1.10.0.0 -> v1.10.0.0
[00014667][12 03][00] v1.10.0.0 -> v1.10.0.0
[00014858][15 00][00] v1.1.2.0 -> v1.1.2.0
[00014941][17 00][00] v1.1.1.7 -> v1.1.1.7
[00015062][17 01][00] v1.0.2.7 -> v1.0.2.7
[00015120][19 00][00] v1.0.8.96 -> v1.0.8.96
[00015163][01 00][00] v1.23.3419 -> v1.23.3419
[00015209][01 01][00] v1.23.3419 -> v1.23.3419
[00015266][08 00][00] v0.12.0.4 -> v0.12.0.4
[00015306]Packet upgrade cancelled at version checking.



[00012518]========== remo-con disconnect. boot(15) ============
[00012565]Packet [C:\P3X_FW_V01.04.0010.bin] detected, card sn [0xb0ce292d].
[00012607]Packet upgrade start...

[00012654]Packet checking...
[00012699]Packet vlink 01.04.0010 <-> 01.03.0020.
[00012747]Record vlink 01.04.0010 <-> 01.03.0020 (flow = 0).
[00012790]Done.

[00012832]Version checking[1]...
[00012918][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012998][03 06][00] v2.3.0.13 -> v2.3.0.13
[00013051][04 00][00] v1.41.0.0 -> v1.41.0.0
[00013118][09 00][00] v1.7.0.3 -> v1.7.0.3
[00013240][11 00][00] v1.7.0.0 -> v1.7.0.0
[00013333][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013432][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013531][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013631][12 03][00] v1.10.0.0 -> v1.10.0.0
[00013767][15 00][00] v1.1.2.0 -> v1.1.2.0
[00013847][17 00][00] v1.1.1.7 -> v1.1.1.7
[00013967][17 01][00] v1.0.2.7 -> v1.0.2.7
[00014018][19 00][00] v1.0.8.96 -> v1.0.8.96
[00014067][01 00][00] v1.23.3419 -> v1.23.3419
[00014109][01 01][00] v1.23.3419 -> v1.23.3419
[00014167][08 00][00] v0.12.0.4 -> v0.12.0.4
[00014302]Packet upgrade cancelled at version checking.



[00012547]========== remo-con disconnect. boot(15) ============
[00012594]Packet [C:\P3X_FW_V01.04.0010.bin] detected, card sn [0xb0ce292d].
[00012636]Packet upgrade start...

[00012685]Packet checking...
[00012729]Packet vlink 01.04.0010 <-> 01.03.0020.
[00012778]Record vlink 01.04.0010 <-> 01.03.0020 (flow = 0).
[00012825]Done.

[00012866]Version checking[1]...
[00012953][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013033][03 06][00] v2.3.0.13 -> v2.3.0.13
[00013087][04 00][00] v1.41.0.0 -> v1.41.0.0
[00013156][09 00][00] v1.7.0.3 -> v1.7.0.3
[00013274][11 00][00] v1.7.0.0 -> v1.7.0.0
[00013372][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013482][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013562][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013649][12 03][00] v1.10.0.0 -> v1.10.0.0
[00013796][15 00][00] v1.1.2.0 -> v1.1.2.0
[00013883][17 00][00] v1.1.1.7 -> v1.1.1.7
[00014027][17 01][00] v1.0.2.7 -> v1.0.2.7
[00014077][19 00][00] v1.0.8.96 -> v1.0.8.96
[00014126][01 00][00] v1.23.3419 -> v1.23.3419
[00014168][01 01][00] v1.23.3419 -> v1.23.3419
[00014262][08 00][00] v0.12.0.4 -> v0.12.0.4
[00014302]Packet upgrade cancelled at version checking.



[00013139]========== remo-con disconnect. boot(15) ============
[00013186]Packet [C:\P3X_FW_V01.04.0010.bin] detected, card sn [0xb0ce292d].
[00013226]Packet upgrade start...

[00013269]Packet checking...
[00013312]Packet vlink 01.04.0010 <-> 01.03.0020.
[00013360]Record vlink 01.04.0010 <-> 01.03.0020 (flow = 0).
[00013398]Done.

[00013439]Version checking[1]...
[00013511][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013591][03 06][00] v2.3.0.13 -> v2.3.0.13
[00013638][04 00][00] v1.41.0.0 -> v1.41.0.0
[00013704][09 00][00] v1.7.0.3 -> v1.7.0.3
[00013835][11 00][00] v1.7.0.0 -> v1.7.0.0
[00013935][12 00][00] v1.10.0.0 -> v1.10.0.0
[00014021][12 01][00] v1.10.0.0 -> v1.10.0.0
[00014109][12 02][00] v1.10.0.0 -> v1.10.0.0
[00014289][12 03][00] v1.10.0.0 -> v1.10.0.0
[00014457][15 00][00] v1.1.2.0 -> v1.1.2.0
[00014539][17 00][00] v1.1.1.7 -> v1.1.1.7
[00014670][17 01][00] v1.0.2.7 -> v1.0.2.7
[00014744][19 00][00] v1.0.8.96 -> v1.0.8.96
[00014783][01 00][00] v1.23.3419 -> v1.23.3419
[00014826][01 01][00] v1.23.3419 -> v1.23.3419
[00014883][08 00][00] v0.12.0.4 -> v0.12.0.4
[00014926]Packet upgrade cancelled at version checking.



[00013051]========== 2015.09.07 16:11:03. boot(15) ============
[00013100]Packet [C:\P3X_FW_V01.04.0010.bin] detected, card sn [0xb0ce292d].
[00013138]Packet upgrade start...

[00013185]Packet checking...
[00013231]Packet vlink 01.04.0010 <-> 01.03.0020.
[00013275]Record vlink 01.04.0010 <-> 01.03.0020 (flow = 0).
[00013315]Done.

[00013356]Version checking[1]...
[00013440][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013521][03 06][00] v2.3.0.13 -> v2.3.0.13
[00013568][04 00][00] v1.41.0.0 -> v1.41.0.0
[00013630][09 00][00] v1.7.0.3 -> v1.7.0.3
[00013761][11 00][00] v1.7.0.0 -> v1.7.0.0
[00013846][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013950][12 01][00] v1.10.0.0 -> v1.10.0.0
[00014048][12 02][00] v1.10.0.0 -> v1.10.0.0
[00014146][12 03][00] v1.10.0.0 -> v1.10.0.0
[00014304][15 00][00] v1.1.2.0 -> v1.1.2.0
[00014400][17 00][00] v1.1.1.7 -> v1.1.1.7
[00014541][17 01][00] v1.0.2.7 -> v1.0.2.7
[00014610][19 00][00] v1.0.8.96 -> v1.0.8.96
[00014653][01 00][00] v1.23.3419 -> v1.23.3419
[00014696][01 01][00] v1.23.3419 -> v1.23.3419
[00014744][08 00][00] v0.12.0.4 -> v0.12.0.4
[00014792]Packet upgrade cancelled at version checking.



[00064393]========== remo-con disconnect. boot(15) ============
[00064438]Packet [C:\P3X_FW_V01.04.0010.bin] detected, card sn [0xb0ce292d].
[00064483]Packet upgrade start...

[00064544]Packet checking...
[00064601]Packet vlink 01.04.0010 <-> 01.03.0020.
[00064647]Record vlink 01.04.0010 <-> 01.03.0020 (flow = 0).
[00064694]Done.

[00064747]Version checking[1]...
[00064833][03 05][00] v34.2.0.9 -> v34.2.0.9
[00064991][03 06][00] v2.3.0.13 -> v2.3.0.13
[00065049][04 00][00] v1.41.0.0 -> v1.41.0.0
[00065115][09 00][00] v1.7.0.3 -> v1.7.0.3
[00065257][11 00][00] v1.7.0.0 -> v1.7.0.0
[00065346][12 00][00] v1.10.0.0 -> v1.10.0.0
[00065445][12 01][00] v1.10.0.0 -> v1.10.0.0
[00065546][12 02][00] v1.10.0.0 -> v1.10.0.0
[00065645][12 03][00] v1.10.0.0 -> v1.10.0.0
[00065794][15 00][00] v1.1.2.0 -> v1.1.2.0
[00065880][17 00][00] v1.1.1.7 -> v1.1.1.7
[00066020][17 01][00] v1.0.2.7 -> v1.0.2.7
[00066095][19 00][00] v0.0.0.0 -> v1.0.8.96 need upgrade.
[00066152][01 00][00] v1.23.3419 -> v1.23.3419
[00066204][01 01][00] v1.23.3419 -> v1.23.3419
[00066266][08 00][00] v0.12.0.4 -> v0.12.0.4
[00066312]Done.

[00068358]Waiting for user confirm...
[00078411]Timeout, start upgrade automatically.

[00078513]Firmware upgrading[1]...
[00081201][19 00] Firmware upgrade start...
[00245594][19 00] Firmware upgrade finished successfully.
[00245642]Done.

[00245689]Version checking[2]...
[00245783][03 05][00] v34.2.0.9 -> v34.2.0.9
[00245867][03 06][00] v2.3.0.13 -> v2.3.0.13
[00245938][04 00][00] v1.41.0.0 -> v1.41.0.0
[00245997][09 00][00] v1.7.0.3 -> v1.7.0.3
[00246130][11 00][00] v1.7.0.0 -> v1.7.0.0
[00246218][12 00][00] v1.10.0.0 -> v1.10.0.0
[00246318][12 01][00] v1.10.0.0 -> v1.10.0.0
[00246418][12 02][00] v1.10.0.0 -> v1.10.0.0
[00246518][12 03][00] v1.10.0.0 -> v1.10.0.0
[00246669][15 00][00] v1.1.2.0 -> v1.1.2.0
[00246780][17 00][00] v1.1.1.7 -> v1.1.1.7
[00246932][17 01][00] v1.0.2.7 -> v1.0.2.7
[00246997][19 00][05] v1.0.8.96 -> v1.0.8.96
[00247051][01 00][00] v1.23.3419 -> v1.23.3419
[00247097][01 01][00] v1.23.3419 -> v1.23.3419
[00247173][08 00][00] v0.12.0.4 -> v0.12.0.4
[00247222]Packet upgrade finish successfully.



[00012559]========== remo-con disconnect. boot(15) ============
[00012606]Packet [C:\P3X_FW_V01.04.0010.bin] detected, card sn [0xb0ce292d].
[00012648]Packet upgrade start...

[00012695]Packet checking...
[00012832]Packet vlink 01.04.0010 <-> 01.03.0020.
[00012875]Record vlink 01.04.0010 <-> 01.03.0020 (flow = 0).
[00012926]Done.

[00012968]Version checking[1]...
[00013056][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013136][03 06][00] v2.3.0.13 -> v2.3.0.13
[00013185][04 00][00] v1.41.0.0 -> v1.41.0.0
[00013256][09 00][00] v1.7.0.3 -> v1.7.0.3
[00013376][11 00][00] v1.7.0.0 -> v1.7.0.0
[00013485][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013590][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013685][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013785][12 03][00] v1.10.0.0 -> v1.10.0.0
[00013928][15 00][00] v1.1.2.0 -> v1.1.2.0
[00014020][17 00][00] v1.1.1.7 -> v1.1.1.7
[00014146][17 01][00] v1.0.2.7 -> v1.0.2.7
[00014226][19 00][00] v1.0.8.96 -> v1.0.8.96
[00014274][01 00][00] v1.23.3419 -> v1.23.3419
[00014319][01 01][00] v1.23.3419 -> v1.23.3419
[00014372][08 00][00] v0.12.0.4 -> v0.12.0.4
[00014424]Packet upgrade cancelled at version checking.



[00012563]========== remo-con disconnect. boot(15) ============
[00012614]Packet [C:\P3X_FW_V01.04.0010.bin] detected, card sn [0xb0ce292d].
[00012658]Packet upgrade start...

[00012702]Packet checking...
[00012753]Packet vlink 01.04.0010 <-> 01.03.0020.
[00012798]Record vlink 01.04.0010 <-> 01.03.0020 (flow = 0).
[00012843]Done.

[00012885]Version checking[1]...
[00012965][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013048][03 06][00] v2.3.0.13 -> v2.3.0.13
[00013103][04 00][00] v1.41.0.0 -> v1.41.0.0
[00013171][09 00][00] v1.7.0.3 -> v1.7.0.3
[00013307][11 00][00] v1.7.0.0 -> v1.7.0.0
[00013406][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013516][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013607][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013707][12 03][00] v1.10.0.0 -> v1.10.0.0
[00013863][15 00][00] v1.1.2.0 -> v1.1.2.0
[00013955][17 00][00] v1.1.1.7 -> v1.1.1.7
[00014076][17 01][00] v1.0.2.7 -> v1.0.2.7
[00014151][19 00][00] v1.0.8.96 -> v1.0.8.96
[00014197][01 00][00] v1.23.3419 -> v1.23.3419
[00014259][01 01][00] v1.23.3419 -> v1.23.3419
[00014391][08 00][00] v0.12.0.4 -> v0.12.0.4
[00014440]Packet upgrade cancelled at version checking.



[00013071]========== remo-con disconnect. boot(15) ============
[00013121]Packet [C:\P3X_FW_V01.04.0010.bin] detected, card sn [0xb0ce292d].
[00013166]Packet upgrade start...

[00013215]Packet checking...
[00013264]Packet vlink 01.04.0010 <-> 01.03.0020.
[00013309]Record vlink 01.04.0010 <-> 01.03.0020 (flow = 0).
[00013355]Done.

[00013399]Version checking[1]...
[00013496][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013579][03 06][00] v2.3.0.13 -> v2.3.0.13
[00013637][04 00][00] v1.41.0.0 -> v1.41.0.0
[00013695][09 00][00] v1.7.0.3 -> v1.7.0.3
[00013817][11 00][00] v1.7.0.0 -> v1.7.0.0
[00013924][12 00][00] v1.10.0.0 -> v1.10.0.0
[00014024][12 01][00] v1.10.0.0 -> v1.10.0.0
[00014124][12 02][00] v1.10.0.0 -> v1.10.0.0
[00014229][12 03][00] v1.10.0.0 -> v1.10.0.0
[00014366][15 00][00] v1.1.2.0 -> v1.1.2.0
[00014461][17 00][00] v1.1.1.7 -> v1.1.1.7
[00014580][17 01][00] v1.0.2.7 -> v1.0.2.7
[00014655][19 00][00] v1.0.8.96 -> v1.0.8.96
[00014700][01 00][00] v1.23.3419 -> v1.23.3419
[00014753][01 01][00] v1.23.3419 -> v1.23.3419
[00014811][08 00][00] v0.12.0.4 -> v0.12.0.4
[00014854]Packet upgrade cancelled at version checking.



[00012636]========== 2015.09.07 18:05:35. boot(15) ============
[00012677]Packet [C:\P3X_FW_V01.04.0010.bin] detected, card sn [0xb0ce292d].
[00012720]Packet upgrade start...

[00012768]Packet checking...
[00012832]Packet vlink 01.04.0010 <-> 01.03.0020.
[00012875]Record vlink 01.04.0010 <-> 01.03.0020 (flow = 0).
[00012917]Done.

[00012958]Version checking[1]...
[00013048][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013131][03 06][00] v2.3.0.13 -> v2.3.0.13
[00013180][04 00][00] v1.41.0.0 -> v1.41.0.0
[00013246][09 00][00] v1.7.0.3 -> v1.7.0.3
[00013369][11 00][00] v1.7.0.0 -> v1.7.0.0
[00013463][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013565][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013662][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013842][12 03][00] v1.10.0.0 -> v1.10.0.0
[00014672][15 00][00] v1.1.2.0 -> v1.1.2.0
[00014763][17 00][00] v1.1.1.7 -> v1.1.1.7
[00014898][17 01][00] v1.0.2.7 -> v1.0.2.7
[00014966][19 00][00] v1.0.8.96 -> v1.0.8.96
[00015010][01 00][00] v1.23.3419 -> v1.23.3419
[00015052][01 01][00] v1.23.3419 -> v1.23.3419
[00015106][08 00][00] v0.12.0.4 -> v0.12.0.4
[00015149]Packet upgrade cancelled at version checking.



[00013037]========== remo-con disconnect. boot(15) ============
[00013090]Packet [C:\P3X_FW_V01.04.0010.bin] detected, card sn [0xb0ce292d].
[00013137]Packet upgrade start...

[00013194]Packet checking...
[00013250]Packet vlink 01.04.0010 <-> 01.03.0020.
[00013296]Record vlink 01.04.0010 <-> 01.03.0020 (flow = 0).
[00013345]Done.

[00013394]Version checking[1]...
[00013501][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013582][03 06][00] v2.3.0.13 -> v2.3.0.13
[00013642][04 00][00] v1.41.0.0 -> v1.41.0.0
[00013701][09 00][00] v1.7.0.3 -> v1.7.0.3
[00013845][11 00][00] v1.6.0.0 -> v1.7.0.0 need upgrade.
[00013966][12 00][00] v1.10.0.0 -> v1.10.0.0
[00014069][12 01][00] v1.10.0.0 -> v1.10.0.0
[00014169][12 02][00] v1.10.0.0 -> v1.10.0.0
[00014314][12 03][00] v1.10.0.0 -> v1.10.0.0
[00014455][15 00][00] v1.1.2.0 -> v1.1.2.0
[00014549][17 00][00] v1.1.1.7 -> v1.1.1.7
[00014694][17 01][00] v1.0.2.7 -> v1.0.2.7
[00014760][19 00][00] v1.0.8.96 -> v1.0.8.96
[00014809][01 00][00] v1.23.3419 -> v1.23.3419
[00014859][01 01][00] v1.23.3419 -> v1.23.3419
[00014922][08 00][00] v0.12.0.4 -> v0.12.0.4
[00014971]Done.

[00017020]Waiting for user confirm...
[00027066]Timeout, start upgrade automatically.

[00027164]Firmware upgrading[1]...
[00027226][11 00] Firmware upgrade start...
[00076279][11 00] Firmware upgrade finished successfully.
[00076331]Done.

[00076379]Version checking[2]...
[00076475][03 05][00] v34.2.0.9 -> v34.2.0.9
[00076571][03 06][00] v2.3.0.13 -> v2.3.0.13
[00076642][04 00][00] v1.41.0.0 -> v1.41.0.0
[00076809][09 00][00] v1.7.0.3 -> v1.7.0.3
[00076945][11 00][05] v1.7.0.0 -> v1.7.0.0
[00077059][12 00][00] v1.10.0.0 -> v1.10.0.0
[00077159][12 01][00] v1.10.0.0 -> v1.10.0.0
[00077259][12 02][00] v1.10.0.0 -> v1.10.0.0
[00077359][12 03][00] v1.10.0.0 -> v1.10.0.0
[00077500][15 00][00] v1.1.2.0 -> v1.1.2.0
[00077593][17 00][00] v1.1.1.7 -> v1.1.1.7
[00077733][17 01][00] v1.0.2.7 -> v1.0.2.7
[00077810][19 00][00] v1.0.8.96 -> v1.0.8.96
[00077859][01 00][00] v1.23.3419 -> v1.23.3419
[00077909][01 01][00] v1.23.3419 -> v1.23.3419
[00077977][08 00][00] v0.12.0.4 -> v0.12.0.4
[00078028]Packet upgrade finish successfully.



[00013196]========== 2015.09.07 22:59:02. boot(15) ============
[00013248]Packet [C:\P3X_FW_V01.04.0010.bin] detected, card sn [0xb0ce292d].
[00013296]Packet upgrade start...

[00013356]Packet checking...
[00013406]Packet vlink 01.04.0010 <-> 01.03.0020.
[00013455]Record vlink 01.04.0010 <-> 01.03.0020 (flow = 0).
[00013504]Done.

[00013559]Version checking[1]...
[00013631][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013735][03 06][00] v2.3.0.13 -> v2.3.0.13
[00013792][04 00][00] v1.41.0.0 -> v1.41.0.0
[00013862][09 00][00] v1.7.0.3 -> v1.7.0.3
[00014016][11 00][00] v1.7.0.0 -> v1.7.0.0
[00014104][12 00][00] v1.10.0.0 -> v1.10.0.0
[00014201][12 01][00] v1.10.0.0 -> v1.10.0.0
[00014303][12 02][00] v1.10.0.0 -> v1.10.0.0
[00014427][12 03][00] v1.10.0.0 -> v1.10.0.0
[00014575][15 00][00] v1.1.2.0 -> v1.1.2.0
[00014659][17 00][00] v1.1.1.7 -> v1.1.1.7
[00014799][17 01][00] v1.0.2.7 -> v1.0.2.7
[00014874][19 00][00] v1.0.8.96 -> v1.0.8.96
[00014925][01 00][00] v1.23.3419 -> v1.23.3419
[00014974][01 01][00] v1.23.3419 -> v1.23.3419
[00015038][08 00][00] v0.12.0.4 -> v0.12.0.4
[00015089]Packet upgrade cancelled at version checking.

sploodge Posted at 2015-9-8 05:51
This looks like it has updated OK..

Check the "About" section in the App and see what it says

fantastic, thanks for the help!

alaniz_entertai Posted at 2015-9-8 08:51
Having same issue with firmware!! Help!

This looks like it updated OK.

Amber Posted at 2015-9-7 19:31
You need to update your controller to 1.3.2. which was the last update and there is no controller  ...

So what you are saying is I need to download 1.3.2 and use that to upgrade my controller? But that's ridiculous.

michael@kuzmin. Posted at 2015-9-8 20:38
So what you are saying is I need to download 1.3.2 and use that to upgrade my controller? But that ...

Oh my GOD. So first of all, yes, you were right. That was my problem. And another problem was that my flash drive was formatted in NTFS and the RC only supports FAT32.

I mean come ON, DJI. I get all these nuances and limitations. I'm totally OK with them. But you have to document it. Why does it always take me at least 24 hours to do a simple firmware upgrade on this thing.

sploodge Posted at 2015-9-8 10:48
This looks like it updated OK.

tried updating controller too. didnt do anything. its flies ok. but my screen says update rc. gonna fly it anyways.