Last edited by tomswell In 2015-9-9 19:25 Editor I'm having controller update issues ... IOS Inspire1 Aircraft update seems ok ========== 2015.08.19 19:22:03 ===================== Packet: WM610_FW_V01.04.00.01.bin Result: Success. When I plug SD card into control with WM610_FW_V01.04.00.01.bin only on it controller shows no blue led and after a few minutes starts to beep. ( DJI GO  indicates upgrade nessecary and that card was only method available ) DJI GO now shows APP 2.20 Aircraft 1.4.00.1 RC 1.2.1.03 other posts imply 1.30.00 is nessecary for RC controler not 1.2.1.03       clarification please I tried SD Card in controller with WM610-FW-V01.03.00.00 and no blue light ...... constant beep after several minutes just can't load 1.30 as indicated by others. safe to fly  1.2.1.03 ? sure would like to try new SW "F" mode features

1.4.0.package have no RC firmware/ See it allways 66 mb
You are need to update RC to 1.3.2 by classic update method/
1.3.2 is the latest firmware for RC

Nemmo Posted at 2015-9-11 20:09
1.4.0.package have no RC firmware/ See it allways 66 mb
You are need to update RC to 1.3.2 by classi ...

OK , I didn't RTFM.
"it is recommended that the users who are using the firmware that older than v1.3.0.00 to update the firmware to v1.3.0.00 before updating the aircraft."
I updated the I1 Aircraft first to 1.4.00.1 with 1.2.1.03 residing on the RC control
What procedure must I follow to get 1.03.0 installed on RC ? SD Card in controller with WM610-FW-V01.03.00.00 results in no blue led ...... constant beep after several minutes
presumably classic update method  = SD card USB connect directly into control and this hasen't worked
"see it always 66MB"  = make sure SD card must have plenty of space ?

You Must put on SD Card 1/3/2 FW then connect SD card with Cardreader to RC and swith ON RC,  Blue led tell You that upgrade has startrd

Nemmo Posted at 2015-9-17 00:27
You Must put on SD Card 1/3/2 FW then connect SD card with Cardreader to RC and swith ON RC,  Blue l ...

I've done just that a dozen times , reformatted SD .... removed photos
all I get is a red led blinking fast with a beep beep beep beep , never blue ?
annoying , fast red with beep occurrs without  SD card also.

still flustered
re-formatted SD(s) FAT32 and downloaded new software copies
tried to progress from 1.2.1.03 residing on the RC control to 1.2.1.06 before trying 1.03.0 ... no good result

tomswell Posted at 2015-9-26 03:17
still flustered
re-formatted SD(s) FAT32 and downloaded new software copies
tried to progress from 1 ...

I'm having exactly the same problems and have done all the things you have, really annoying for the ap to keep telling you to up grade, no help on here or from dji, poor service

Just checked to see if any help offered for this thread,, and none,,, am I surprised,,  err no

Helipete Posted at 2016-1-12 07:34
Just checked to see if any help offered for this thread,, and none,,, am I surprised,,  err no

You were having firmware update issues 3 months ago, are you still needing assistance after 3 months?

DJI-Ken Posted at 2016-1-12 09:14
You were having firmware update issues 3 months ago, are you still needing assistance after 3 mont ...

I finally sent my controller to DJI and with no feedback it was returned at no cost programmed correctly.

tomswell Posted at 2016-2-15 08:00
I finally sent my controller to DJI and with no feedback it was returned at no cost programmed cor ...

Great, glad it was taken care of.