Hi All;

I have read lots of treats about mini 3 pro jello efect, also i have similiar experience but it is very rare. Today i realized that it happens only vertical mode and while going up and backwards. At the other scenarios there is no problem. What do you think about this? I think gimbal quality is not best option if you compare with mavic series.

Hi there. Will it be fine if you show us a video? You can upload it to YouTube or Google Drive and then paste the link here. Thank you.

Make sure all the props are A ok, no nicks of any sort, not bent from being in the prop holder etc...

You must show what it looks like. I've never had this problem before.

+1 check your props,  this is the number 1 cause of vibration.

Here is the video!

https://youtube.com/shorts/TIf_aCzwbVA?si=_9vIUlS04PxA5bLx

DAFlys Posted at 2-28 01:57
+1 check your props,  this is the number 1 cause of vibration.

One matter that i did not understand, why only flying up and backwards. If the props are defective, does not it efect all types flight?

BRS64 Posted at 2-28 11:34
One matter that i did not understand, why only flying up and backwards. If the props are defective, does not it efect all types flight?

Flying backwards like that will be changing which props are doing the majority of the work as the attitude of the drone will be different.   

Did you check your props?

DAFlys Posted at 2-29 01:16
Flying backwards like that will be changing which props are doing the majority of the work as the attitude of the drone will be different.   

Did you check your props?

here is the link, everything looks perfect.

https://drive.google.com/file/d/ ... 7j/view?usp=sharing

BRS64 Posted at 3-1 10:17
here is the link, everything looks perfect.

https://drive.google.com/file/d/1iuJpBZCUfsBgBdJ9cpTYI7Vvjoxwm97j/view?usp=sharing

Have you inspected the props though?

BRS64 Posted at 2-28 11:31
Here is the video!

https://youtube.com/shorts/TIf_aCzwbVA?si=_9vIUlS04PxA5bLx

If the drone has ever crashed or experienced any collisions, we recommend sending the drone for diagnosis. If not, can you please follow  the steps below:
1. Please check whether the ambient temperature during drone operation falls within the operating temperature range provided on our website. Low temperature may cause vibration in the gimbal.
2. Kindly remove the gimbal protector before powering on the aircraft to prevent the gimbal motor from being stuck, or the gimbal will become shaky.
3. Please make sure that the gimbal is in Follow mode. If it is set to FPV mode, the gimbal view will be tilted when the aircraft tilts.
4. Please check whether the aircraft is in Sports mode (S-mode) when the gimbal becomes shaky. In S-mode, greater emphasis is placed on flight performance. During flight, when the aircraft attitude is too large, the gimbal attitude stabilization cannot be guaranteed. If the gimbal is shaky in S-mode only, which is normal, please switch the flight mode of the aircraft to Normal mode (N-mode) or Cine mode (C-mode) to achieve a more stable view.
5. Please check whether the wind was strong in the flight environment. If the wind is too strong, the aircraft will vibrate, resulting in the image transmission screen being shaky. We recommend that you test the gimbal in a windless or breezy environment.
6. Have you ever adjusted the EXP value of the aircraft? EXP refers to the drone's exponential. The higher the EXP value, the higher the aircraft response sensitivity, indicating that the aircraft will respond flexibly to small stick movement. If you have ever adjusted the EXP value, please go to [Control -> Gain & Expo Tuning] in the app, reset the parameters, and then test the aircraft again.
7. Please perform gimbal calibration in the app. Using with DJI Fly: [Settings -> Control -> Gimbal Calibration].
If the steps above were done and the issue persists, we advise submitting an Online Repair Request and sending the aircraft back to DJI for further diagnosis. https://repair.dji.com/. Please keep us posted. Have a great day ahead.

DAFlys Posted at 3-2 00:50
Have you inspected the props though?

yes. I checked them.

DJI Tony Posted at 3-3 03:35
If the drone has ever crashed or experienced any collisions, we recommend sending the drone for diagnosis. If not, can you please follow  the steps below:
1. Please check whether the ambient temperature during drone operation falls within the operating temperature range provided on our website. Low temperature may cause vibration in the gimbal.
2. Kindly remove the gimbal protector before powering on the aircraft to prevent the gimbal motor from being stuck, or the gimbal will become shaky.

Thanks for feedback. I saw recommendations about IMU calibration and adding ND filters at some treats.

What changes if i apply these?

BRS64 Posted at 3-3 07:23
Thanks for feedback. I saw recommendations about IMU calibration and adding ND filters at some treats.

What changes if i apply these?

Hi there. IMU helps keep the aircraft steady but not the gimbal and the ND filter adds weight to the camera. Have a great day.

How is it going now?