Please select Into the mobile phone version | Continue to access the computer ver.
DJI Spark - app go 4 not supported in latest Android
244 10 10-21 17:37
Uploading and Loding Picture ...(0/1)
o(^-^)o
RoneyR
lvl.1
Australia
Offline

Hi DJi Friends,

@DJI Mindy  @DJI Support @DJI Natalia

I'm still flying the magnificent DJI Spark (even though its vintage).
What i understand is DJI Go 4 is the only app that supports the Spark.

The DJI GO 4 app downloaded from DJI site is not allowed for installation in Android mobile.
Could you please send me the solution to fix for the 'DJI Go 4' app?  

My phone : Samsung S24 Ultra , using Android v14,

If not DJI Go 4 , what app can be used for my SPARK's Flight ?


Kindly assist me
Many thanks in advance


Cheers
Roney


10-21 17:37
Use props
Timothy.martin82
lvl.1
Flight distance : 4081 ft
United Kingdom
Offline

I just noticed the same problem!

Pixel 7 Pro.
10-22 03:22
Use props
DJI Natalia
Administrator
Offline

Hi there, thank you for reaching out. We have responded to your previous post concerning this matter. Please review the provided steps and update us on the results. You can refer to the following link for the response:
[https://forum.dji.com/forum.php? ... 751&pid=3450750].

Do not hesitate to contact us back if you encounter any challenges. Thank you for your understanding and support!
10-22 03:52
Use props
DJI Natalia
Administrator
Offline

Timothy.martin82 Posted at 10-22 03:22
I just noticed the same problem!

Pixel 7 Pro.

HI there, thank you for reaching out and we do apologize for the trouble caused. May I confirm the DJI App that you're trying to install? Also, try the following steps and see it that helps :

1. Go to the mobile phone’s “System Settings” and find “Installing an Unknown Application”. Enable the “Allow application installation from this source” switch.
2. Check the mobile phone’s internal storage, and clear its cache. The remaining memory must be greater than 2GB.
3. If there is Google Play installed on this phone, please disable "Google Play Protect"
4. If the “Installing an Unknown Application” setting has been enabled, please back up the photos and videos. Uninstall the earlier version of the app and then restart the mobile phone. Download and install the app from the DJI official website.


Keep us posted the outcome and thank you for your understanding!
10-22 03:53
Use props
Timothy.martin82
lvl.1
Flight distance : 4081 ft
United Kingdom
Offline

Perfect, thanks!!
10-22 10:08
Use props
RoneyR
lvl.1
Australia
Offline

DJI Natalia Posted at 10-22 03:53
HI there, thank you for reaching out and we do apologize for the trouble caused. May I confirm the DJI App that you're trying to install? Also, try the following steps and see it that helps :

1. Go to the mobile phone’s “System Settings” and find “Installing an Unknown Application”. Enable the “Allow application installation from this source” switch.

Thanks Natalia - it worked , disabling the Google play protect

appreciate the support
10-22 14:33
Use props
RoneyR
lvl.1
Australia
Offline

After i installed the app - connecting to the spark , i am getting "Gimbal overloaded" and other times "No GPS signal"  message.
The lights below the drone - showing these different colours (as attached in the image).

I tried the resolution mentioned here - but no change to the error.
https://support.dji.com/help/content?customId=en-us03400006791&spaceId=34&re=ID&lang=en&documentType=artical&paperDocType=paper
10-22 18:07
Use props
DJI Natalia
Administrator
Offline

RoneyR Posted at 10-22 14:33
Thanks Natalia - it worked , disabling the Google play protect

appreciate the support

Hi there, thank you for the update and we're glad that the steps shared above fixed the issue. Do not hesitate to contact us back if there's any further inquiry.

Thank you for your continued support!
10-22 22:43
Use props
DJI Natalia
Administrator
Offline

RoneyR Posted at 10-22 18:07
After i installed the app - connecting to the spark , i am getting "Gimbal overloaded" and other times "No GPS signal"[view_image]  message.
The lights below the drone - showing these different colours (as attached in the image).

HI there, thank you for sharing the picture . Please restart the device and re-upgrade the firmware. If the issue still persists after several attempts,  the best course of action would be to submit an online repair request here: {https://repair.dji.com/repair/index}. If you need assistance with creating a ticket, you may contact DJI support at https://www.dji.com/support. We understand that this is not the answer that you look forward to, but this would be the best thing to do in this situation. In addition, warranty service can be claimed depending on the result of the Damage Assessment.

Your kind understanding is appreciated and thank you for your continued support.
10-22 22:45
Use props
Wolferl
First Officer
Flight distance : 46325 ft
Austria
Offline

RoneyR Posted at 10-22 18:07
After i installed the app - connecting to the spark , i am getting "Gimbal overloaded" and other times "No GPS signal"[view_image]  message.
The lights below the drone - showing these different colours (as attached in the image).

Hi RoneyR,

As for the Gimbal  Overload message, you should remove the gimbal protect thingy before powering up the drone.

HTH,
Wolferl


10-23 04:01
Use props
djiuser_wV94Vt3Qc2AV
New
Flight distance : 10837 ft

Poland
Offline

Hi guys,

I have a problem with connecting my phone Samsung Galaxy S24 with DJ GO 4 and Mavic 2 pro.

All connection works but I have no view from camera.
When I am conecting older phones like Samsung s23 it's works, A53 Samsung works as well.

Is DJ GO 4 doesn't support new Samsung S24?
I know that new apk DJ Fly does, but they it not supporting Drone Mavic 2 pro.
11-29 03:51
Use props
Advanced
You need to log in before you can reply Login | Register now

Credit Rules