Hello,

I have the Lighbridge 2 with the A2 on an s900.

I'm trying to configure it.

There is a few things I can't seem to be able to do:

1) I can't get the a2 to go in failsafe mode when turning the tx off, the flight mode switch works, but when turning tx off, the flight mode stays in it's original position. I don't see any failsafe settings on the tx itself. Anyone with the same problem?

2) Since the cruise control and IOC need 3 ways switches, how do you make it work with the  lightbridge 2, there is only one 3 way switch for the flight mode. Dji says LB2 is compatible with the A2, so surely we should be able to use the functions of the A2. How did you guys do it?

Thanks lots

Nico

Hello!
Please review the instruction information in the P30-P32 of the A2 User Manual at: https://dl.djicdn.com/downloads/a2/en/A2_User_Manual_en_v1.24.pdf, and please go through P55-P62 to check your mapping in the A2 Assistant software.

DJI-Adela Posted at 2016-4-24 03:46
Hello!
Please review the instruction information in the P30-P32 of the A2 User Manual at: https://dl ...

You did not answer my question, let me try again:

Since the cruise control and IOC need 3 ways switches, how do you make it work with the  lightbridge 2, there is only one 3 way switch for the flight mode. Dji says LB2 is compatible with the A2, so surely we should be able to use the functions of the A2. How did you guys do it?

nico@bugeyefilm Posted at 2016-6-3 00:04
You did not answer my question, let me try again:

Since the cruise control and IOC need 3 ways sw ...

Hello, Nico
The 3 position switch on the Ground Station of Lightbright 2 is set as the Flight Mode control switch by default, you just need to connect the Lightbright 2 to your drone system correctly, and map the F mode in the A2 Assistant software.

Please let me know if you have any question.
Thanks.

DJI-Adela give me an example of how to activate or operate failsafe, IOC, CC

with lightbridge 2

If you enable multiple flight modes in the app then you can select the options in the app as well.  RTH is activated when you set it up to do so when the RC looses signal.  If you look in Assistant 2 then when the RC is turned off then that will initiate RTH if that is how you have it set up.

Tahoe_Ed Posted at 2016-6-10 00:39
If you enable multiple flight modes in the app then you can select the options in the app as well.   ...

hi,

where you enable multiple flight modes in the app?
and for the CC and IOC?

Victor

victorpinto Posted at 2016-6-10 07:17
hi,

where you enable multiple flight modes in the app?

It will take me a while to power my A3.  Please be patient.

Tahoe_Ed Posted at 2016-6-10 01:34
It will take me a while to power my A3.  Please be patient.

I have A2 what should I do?

victorpinto Posted at 2016-6-10 07:36
I have A2 what should I do?

I think the App reacts to them similarly.  We will find out.  I have not had a A2 since October when we began testing the A3.  If I cannot answer your question then I can forward on the HQ for an answer.

Tahoe_Ed Posted at 2016-6-10 01:43
I think the App reacts to them similarly.  We will find out.  I have not had a A2 since October wh ...

It is expected to insert  DC and IOC later in app?

Tahoe_Ed Posted at 2016-6-10 07:39
If you enable multiple flight modes in the app then you can select the options in the app as well.   ...

Hello Taho_Ed
In LB2 DJI go app, where can i see muliple flight modes ?
i have S1000+, GH4, A2, LB2.
i also have question that when i turn off Remote controller, and then in failsafe, A2 GPS position indicator is not move to failsafe indicator.
and i cannot see HL,CL icon in upper center of galaxy tab screen.  

DJI-Adela Posted at 2016-6-4 14:31
Hello, Nico
The 3 position switch on the Ground Station of Lightbright 2 is set as the Flight Mode ...

Hello DJI-adela
map F mode  in A2 software
-> where can i map F mode  in A2 assistatna software ?