theo54au
lvl.1
Philippines
Offline
|
I have had my P3P stored for a few months. The battery of the RC was dead flat.
The Battery of the P3P still had 2 bars.
I recharged both batteries and started them as per instructions (RC first, then the P3P and last my Asus tablet) I get “No Signal”. I follow the same procedure again and I see “Disconnected”.
Again, I follow the same procedure and I see “No Signal”. There is also an update notification on the RC. I update the RC successfully from 1.3.20 to V.1.6.0
I check if there are updates for the P3P. There are, I was running V1.3.20 and I download V1.8.80.
I follow the update procedure as per instructions. I turn on the P3P and the camera LED flashes green (warming up), then solid green, and after a few seconds alternating green/red. (Installing update) After 17 seconds the gimbal motors seem to run constant and the Camera light turns solid red.(Fail) I wait about 20 minutes but nothing changes and the gimbal gets really hot. (Failed)
I turn it off and try again, same result, I try again with another memory card, same result.
I format the card and try again, same result.
I check the App for the version of the firmware: It says: V.1.8.80 (??) After a failed update?
I check for an update on the app, that was available and I downloaded and installed the update ver.2.8.1 from 2.3.0
I turn on the RC, the P3P and last the app. No connection or whatsoever, can not even go in camera mode. Retried again and again, no camera mode. I uninstalled the update and re-installed the old version. Now I can go in camera mode, but still “No Signal”.
I installed the app V.2.8.1 on my Lenovo android phone, same result: No Signal.
When I turn on the RC the LED is red, when I turn on the P3P the LED on the RC turns green.
I tried RC linking but it runs into “Time-Out”.
This is where I am now, 3 days later and still no signal.
Any help would be appreciated!
At this moment I am running:
App V.2.3.0 on the Asus Tablet or V.2.8.1 on the Lenovo Smartphone
RC V1.6.0
Firmware V.1.8.80 (Even though it failed)
Here is the Log: (Note the incorrect dates)
========== 2014.01.01 00:00:12 remo-con disconnect======
Packet: P3X_FW_V01.04.0010.bin
========== 2014.01.01 00:00:12 remo-con disconnect======
Packet: P3X_FW_V01.04.0010.bin
========== 2014.01.01 00:00:11 remo-con disconnect======
Packet: P3X_FW_V01.04.0010.bin
Upgrading ...
Result: Success.
========== 2015.10.05 20:08:50 =====================
Packet: P3X_FW_V01.04.0010.bin
Result: Abort.
The firmware on the SD card is identical to or older than the current firmware on the aircraft.
========== 2014.01.01 00:00:14 remo-con disconnect======
Packet: P3X_FW_V01.08.0080.bin
Upgrading ...
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.
========== 2014.01.01 00:00:13 remo-con disconnect======
Packet: P3X_FW_V01.08.0080.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.
========== 2014.01.01 00:00:14 remo-con disconnect======
Packet: P3X_FW_V01.08.0080.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.
========== 2014.01.01 00:00:14 remo-con disconnect======
Packet: P3X_FW_V01.08.0080.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.
========== 2014.01.01 00:02:48 remo-con disconnect======
Packet: P3X_FW_V01.08.0080.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.
========== 2014.01.01 00:00:14 remo-con disconnect======
Packet: P3X_FW_V01.08.0080.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.
========== 2014.01.01 00:00:14 remo-con disconnect======
Packet: P3X_FW_V01.07.0060.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.
========== 2014.01.01 00:00:14 remo-con disconnect======
Packet: P3X_FW_V01.08.0080.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.
|
|