I am installing an X5 + LB2 + A3 and voltage do not know what power the X5, someone can tell me something?

Could you clarify what frame you are attempting to install this system on?

I think that the picture is not significant, but is a Gryphon

DJI-Jamie Posted at 2016-8-27 00:23
It can only work with the A3 when paired with Lightbridge 2 and the M600 X Mounting Kit.

what you say, means that the X 5 should not buy if you don't have the 600 Matrice

Juan carlos3 Posted at 2016-9-3 03:28
DJI-Jamie Posted at 2016-8-27 00:23
It can only work with the A3 when paired with Lightbridge 2 and  ...

The X mounting kit can be used in tandem with the X5, Lightbridge 2 and the A3 without the M600. In your case, however, potential modifications to the frame attachment may be needed. You should follow the instructions in the M600 manual for the proper cable and power connections.

the fixing to the frame use the of the matrice 600 adapted, what not is specifies in any site is the range of voltage to feed the X5
the LB2 feeds you the X 5 to 12v, the retractable 2-6s, but the X5..
that is my doubt

Hi Juan,
The x5 is connected direct to the LB2 and the gimbal takes its power from a common power rail on the M600, its not clear on the specs what the actual voltage is. I will measure it tomorrow and report back.
r

Thanks ricci2
I try to ensure I if lipo 4s could feed the X5

Hi Juan, i have the same setup also on a Gryphon frame, with a 6s battery setup, to be safe i installed a 12 volt 3A regulator, also very interested to know what the actual voltage it can handle and if it can be run directly from the 6S lipo on 25 volts, For now untill someone actually measures the voltage on a Matrice 600 to be safe run it through a regulator

ricci2 Posted at 2016-9-4 03:32
Hi Juan,
The x5 is connected direct to the LB2 and the gimbal takes its power from a common power ra ...

Hi Ricci2, Thanks also been looking for this measurement for a while

6s, I rest assured that, by some site I haven't read something 18V. Which is not how much to 18v
The X5 feeds the LB2 to 12v, that also I have clear
I want to trust that it works with 4s, but connect and burn something I'm afraid
I apologize, but I am a coward

David, una pregunta, que hace el HRT de la estación?

Hi,
These are the voltages as measured on the M600.
18v x5.
24v esc.
24v landing servo.
Since there is two voltages I expect there is a pmu device dropping the voltage.
Hope that helps.

those voltages are good but...
X5 18     but there are people that leads to 12v with bec
24v ESC    If take 6s are 24v charged,21v to half load,already do not have 24v
24v landing servo     that works 3-6s

I think that they must have a range of work, but when you get off the battery would be below those voltages

It rare dry not between nobody of DJI to clarify this issue, and to my by email nor I have said nothing

Fully charged battery on the M600 is 57v so plenty of scope to run for 35 mins using emu @ 24v.

r

14s????????

I guess that you proves to 4s, if 18v are recommended and there are people going has 12v, 4s anger well!

I think that me talta the cable from positive, it can confirm someone
are the cables that van's X 5 to LB2  The LB2 does not have current

Juan carlos3 Posted at 2016-9-8 19:58
I think that me talta the cable from positive, it can confirm someone
are the cables that van's X 5  ...

you are using the wrong cable for the Dbus input, it should be the one supplied with the A3 it has a red wire in the pin that you can see in this picture that is empty

Juan carlos3 Posted at 2016-9-8 19:58
I think that me talta the cable from positive, it can confirm someone
are the cables that van's X 5  ...

there is no power from the X5 to LB2

ricci2 Posted at 2016-9-5 15:05
Hi,
These are the voltages as measured on the M600.
18v x5.

Thanks for the info, I also found this in the M600manual

Juan carlos3 Posted at 2016-9-8 19:58
I think that me talta the cable from positive, it can confirm someone
are the cables that van's X 5  ...

The photos are no
tis blame of computer?

david.visagie Posted at 2016-9-9 02:28
you are using the wrong cable for the Dbus input, it should be the one supplied with the A3 it has ...

Thank you has appeared the wire

with 4S functions well, if not with 18v be faster

DJI-Jamie Posted at 2016-9-2 20:11
The X mounting kit can be used in tandem with the X5, Lightbridge 2 and the A3 without the M600. In your case, however, potential modifications to the frame attachment may be needed. You should follow the instructions in the M600 manual for the proper cable and power connections.

Hi Jamie
Did you find out if the x5 can be run on a 6s battery
Thanks
Karl

fans3f39f9f6 Posted at 2017-1-6 06:49
Hi Jamie
Did you find out if the x5 can be run on a 6s battery
Thanks

The X Mount can use a 18v - 26v 6S battery, if that's what you're referring to.

right X3/5 mount use 4-6S, we are using 6S from the XT60 connection on the S900/1000

ducpeter Posted at 2017-1-17 11:59
right X3/5 mount use 4-6S, we are using 6S from the XT60 connection on the S900/1000

Is this still working for you? I am going to use 6s to power my x3 mount. I just wanted to make sure your camera held up under 6s. Thanks very much.

Yes still working with no problems on x3 and x5 with 6s