Phantom 4 Pro/Pro+ Release Notes

• Date : 2017.04.12
• Aircraft Firmware : V 01.03.0509
• Phantom 4 Pro Remote Controller Firmware : V 1.4.0.0
• Phantom 4 Pro+ Remote Controller Firmware : V 1.1.3.0
• DJI GO 4 App iOS : V 4.0.7
• DJI GO 4 App Android : V 4.0.6
  

What’s New?

• Optimized No-Fly Zone Return to Home and unlocking.  
• Improved 4K video recording stability.
  

Phantom 4 Pro/Pro+ Release Note

• Aircraft Firmware : V 01.02.0304
• Phantom 4 Pro Remote Controller Firmware : V 1.3.0.0
• Phantom 4 Pro+ Remote Controller Firmware : V 1.1.1.1
• DJI GO 4 App iOS : V 4.0.2
• DJI GO 4 App Android : V 4.0.1
  

What’s New?

• Fixed an issue of some settings not being reset after resetting camera settings.
•   Fixed color deviations when shooting at a high ISO value.
•   Fixed a rare issue where a black image is saved instead of a photo.
• Fixed an occasional IMU calibration failure issue for the aircraft.
•   Reduced aircraft vibration during light-throttle take-off.
  

Notes:

• The DJI GO app does not support the Phantom 4 Pro. Please use the DJI GO 4 app.
• Due to the size of the firmware, the use of a Micro SD card is recommended when upgrading the Phantom 4 Pro+ Remote Controller
  

Phantom 4 Pro/Pro+ Release Note
Date : 11/25/2016
Aircraft Firmware : V 01.01.0201
DJI GO 4 App iOS : V 4.0.0
DJI GO 4 App Android : V 4.0.0

What’s New?

• Fixed an issue of some settings not being reset after resetting camera settings.
• Fixed color deviations when shooting at a high ISO value.
• Fixed a rare issue where a black image is saved instead of a photo.
• Fixed an occasional IMU calibration failure issue for the aircraft.
• Reduced aircraft vibration during light-throttle take-off.
  

Notes:

• The DJI GO app does not support the Phantom 4 Pro. Please use the DJI GO 4 app.
• Due to the size of the firmware, the use of a Micro SD card is recommended when upgrading the Phantom 4 Pro+ Remote Controller.
  

HDMI module works?

ooooh I hope it fixes all the IMU issues.... I'll go and buy one then

What about the app? I'd like to adjust yaw speed, but it's not saved after changing. Very frustrating, because footage remains jerky like that.

I do not get the remote firmware 1.3.0.0. it show in the about screen as 1.1.0.0. the ac has 1.1.203.

Good job releasing it today, Friday!

Can someone confirm the IMU Calibration is fixed? I can't test it myself really, because i only had this issue only once.

Ange1walk Posted at 2016-12-9 15:55
Good job releasing it today, Friday!

Can someone confirm the IMU Calibration is fixed? I can't test it myself really, because i only had this issue only once.

Not personally but i spoke on the phone today with my dealer who had 2 units with the issue and it resolved the issue with both units straight away.

Cotti7 Posted at 2016-12-9 17:58
Not personally but i spoke on the phone today with my dealer who had 2 units with the issue and it resolved the issue with both units straight away.

Alright great to hear, hopefully it worked for everybody & they are so excited that nobody posts here

And btw to everyone, i noticed it says now (can't remember 100% the last digits but)

RC Version: 01.03.xxx.xxx
AC Version 01.01.0203  shouldn't the AC Version be always higher than RC?
And also, i think they forgot to change that 0203 number, last firmware was 0203 too?

It says "Latest Firmware!" for me.

Just done the firmware update and performed an IMU well done DJI it completed ok :-)

ulisse Posted at 2016-12-9 12:45
HDMI module works?

The HDMI module works perfect!!

Thanks DJI!

fans40906751 Posted at 2016-12-10 04:02
The HDMI module works perfect!!

Worked for me too!!

Fixed an occasional P4P IMU calibration failure issue for the aircraft.  !!!!!!!!!!!!!!!!!!!!!!!!!!!  
This was every IMU calibration on two separate aircraft !!!!!!!!!
I returned new P4P because of this issue in case it was a hardware issue.
I was send an image of a successful calibration due to the new firmware update, wonderful
What a massive mess up on DJI's part allowing this to happen, basics I'd say

High Flyer Posted at 2016-12-9 23:37
Fixed an occasional P4P IMU calibration failure issue for the aircraft.  !!!!!!!!!!!!!!!!!!!!!!!!!!!  
This was every IMU calibration on two separate aircraft !!!!!!!!!
I returned new P4P because of this issue in case it was a hardware issue.

I am surprised DJI ask people to send their drones back when they know full well it will be fixed with the firmware Update, I find it very odd they do that.

mikesher.live Posted at 2016-12-10 05:11
Worked for me too!!

OK connect up a monitor to the hdmi, switch everything on, now go into goapp to HD page, turn off green slider to stop the hdmi feed!  see what happens,

My go app image froze at this stage but telemtry continued,  my hdmi monitor which should be off now is still on and working ?  bugs still.

fans40906751 Posted at 2016-12-9 15:02
The HDMI module works perfect!!

Please excuse what might be a stupid question but what exactly is the HDMI module used for?  I just sold my P3Pro and am awaiting my new P4Pro+

Thank you for the help.

Bud

fans69a1db85 Posted at 2016-12-10 08:11
Please excuse what might be a stupid question but what exactly is the HDMI module used for?  I just sold my P3Pro and am awaiting my new P4Pro+

Thank you for the help.

It is module on the bottom or the remote controller that has only USB for your phone.  The separately sold HDMI module allows you to use FPV goggles.

What happened with color profiles?
Please rearrange the correct profiles.
Thanks

Snowwolfwarrior Posted at 2016-12-10 12:08
I am surprised DJI ask people to send their drones back when they know full well it will be fixed with the firmware Update, I find it very odd they do that.

I agree - I had the -22 IMU calibration error and reported it on 2 Dec - endless emails back and forth and finally received my UPS label to send to DJI NL - picked up on Thursday morning then the firmware update came out the next day... Had they said hold onto to it for another 24 hours I'd be flying it now but no, it's en route to the Netherlands from the UK for what appears to be a basic firmware update!
They either do it to ensure that is the only issue for safety reasons or there is a very poor communication channel between departments - probably the latter as the P4P wouldn't have been sold in the first place with IMU errors if quality controls were of paramount importance!
I wouldn't mind too much if the unit was a couple of hundred quid but the P4P is supposed to be a state-of-the-art prosumer drone that set me back £1,589... And not only I'm yet to fly it but it's in another country when it basically doesn't need to be. Disappointing and actually quite embarrassing all round to be honest!

Can you do a Video on how to update in P4P+ where new controller came with its own display. I am not able to get the upgrade started although I connect OTG cable to Phantom 4 Pro and connected to controller. Nothing happens

smokey_truck Posted at 2016-12-10 15:35
Can you do a Video on how to update in P4P+ where new controller came with its own display. I am not able to get the upgrade started although I connect OTG cable to Phantom 4 Pro and connected to controller. Nothing happens

Ok I was finally able to connect the RC and P4P+ connected and it shows downloading but it has been downloading for a very long time and the update size is 83.0 MB and one light has been blinking red and yellow. How to make it go faster? is it possible to download to SD card and put into the craft to update?


Smokey

smokey_truck Posted at 2016-12-10 16:14
Ok I was finally able to connect the RC and P4P+ connected and it shows downloading but it has been downloading for a very long time and the update size is 83.0 MB and one light has been blinking red and yellow. How to make it go faster? is it possible to download to SD card and put into the craft to update?

Lol, Not sure who is not smart here, on my screen it had been showing downloading for very long time at the end I lost patience and I touched the downloading ICON to find out, it had downloaded and it started to update the craft after that.

Smokey

Every time I try and upgrade using DJI Assist the firmware downloads but overtime it tries to upgrade its says 'Upgrade Failed!' . This happens even when I try to refresh the current firmware on my P4P. What am i doing wrong?

ulisse Posted at 2016-12-10 14:15
What happened with color profiles?
Please rearrange the correct profiles.
Thanks

Yes, this.  Everywhere I have gone online everyone recommends shooting in the Art mode.  Why was it removed?  This is very unfortunate and inconvenient, especially since it was removed without explanation.  Is this an error?  Will it come back?

Please let us know!

Fixed! IMU-calibration done!

After the update my Samsung Tablet now is able to access camera settings and other touch screen features that wouldn't work before. Great it is fixed (I think) Not so great it has obviously taken a long time to get it done. Hopefully this will stop my horizon from being out of whack as well. Cautiously optimitic. Just want things to work....

shayward Posted at 2016-12-12 07:41
After the update my Samsung Tablet now is able to access camera settings and other touch screen features that wouldn't work before. Great it is fixed (I think) Not so great it has obviously taken a long time to get it done. Hopefully this will stop my horizon from being out of whack as well. Cautiously optimitic. Just want things to work....

Which Samsung tablet do you have?

Chest Rockwell Posted at 2016-12-11 01:51
Yes, this.  Everywhere I have gone online everyone recommends shooting in the Art mode.  Why was it removed?  This is very unfortunate and inconvenient, especially since it was removed without explanation.  Is this an error?  Will it come back?

Please let us know!

I don't understand how something gets fixed and in the process of doing so, they mess up something else...

I beta test phones and you would be surprised how much this happens....

Hello,

after I updateted the new firmeware on the Phantom 4 pro yesterday there is now a text standing above the  number of pictures an Video Time I can take which says: "Activate BackTrack for RTH"
What does it mean? Can somebody  help  me with this one?

Thank you

ulisse Posted at 2016-12-11 03:15
What happened with color profiles?
Please rearrange the correct profiles.
Thanks

Hey Ulisse I finally got around to putting the video up here

hvilorio Posted at 2016-12-13 00:24
I don't understand how something gets fixed and in the process of doing so, they mess up something else...

Incompetence, poor quality control, growing to fast, incompetence

This update rendered y gimbal useless. It was stuck in a downward forward position and would not initiate on start up. I reverted back 3 firmware builds just to fix it.

Coffee Posted at 2016-12-15 00:20
This update rendered y gimbal useless. It was stuck in a downward forward position and would not initiate on start up. I reverted back 3 firmware builds just to fix it.

be shure you have not the gimbal fixed by the gimbal glamp during updating !

smokey_truck Posted at 2016-12-10 13:14
Ok I was finally able to connect the RC and P4P+ connected and it shows downloading but it has been downloading for a very long time and the update size is 83.0 MB and one light has been blinking red and yellow. How to make it go faster? is it possible to download to SD card and put into the craft to update?

That was recommended in opening post,

New Update in my birthDay , thx DJI :')

about how often does dji update? everymonth or two?

When are we getting a P4P+ RC update? This is getting ridiculous that we're still stuck on an outdated version of the GO4 app.

When upgrading the batteries on P4P+, will they work normally if used with P4?