After I upgrade my P3P firmware to the latest. I can't link the RC and P3P.

App version: 3.1.15
RC firmware: 1.9.2
P3P firmware: 01.11.0020

Left LED on RC turns solid red. when linking with P3P, it blinks blue.
LED next to link button on P3P, blink G - R - G -R. front LED is blinking red.

Tried to link RC many times, no luck.

Upgrade log:

[00012768]========== remo-con disconnect. boot(15) ============
[00012838]Packet [C:\P3X_FW_V01.11.0020.bin] detected, card sn [0x88994322].
[00012909]Packet upgrade start...

[00012981]Packet checking...
[00013054]Packet vlink 01.11.0020 <-> 01.11.0020.
[00013125]Record vlink 01.10.0090 <-> 01.10.0090 (flow = 0).
[00013197]Done.

[00013268]Version checking[1]...
[00013402][03 06][00] v2.4.20.28 -> v2.4.20.50 need upgrade.
[00013518][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013605][04 00][00] v1.48.0.0 -> v1.48.0.0
[00013758][11 00][00] v1.8.0.0 -> v1.8.0.0
[00013918][11 01][00] v1.8.0.0 -> v2.0.0.33, firmware v1.8.0.0 not support.
[00013990][11 01][00] v1.8.0.0 -> v2.0.0.33
[00014111][12 00][00] v1.11.0.0 -> v1.12.0.0 need upgrade.
[00014258][12 01][00] v1.11.0.0 -> v1.12.0.0 need upgrade.
[00014417][12 02][00] v1.11.0.0 -> v1.12.0.0 need upgrade.
[00014550][12 03][00] v1.11.0.0 -> v1.12.0.0 need upgrade.
[00014725][15 00][00] v1.1.2.0 -> v1.1.2.0
[00014846][17 00][00] v1.1.1.7 -> v1.1.1.7
[00015006][17 01][00] v1.0.2.7 -> v1.0.2.7
[00015097][19 00][00] v1.0.8.96 -> v1.0.8.96
[00015170][01 00][00] v1.32.5432 -> v1.32.5432
[00015242][01 01][00] v1.32.5432 -> v1.32.5432
[00015323][08 00][00] v0.13.0.7 -> v0.13.0.7
[00015437][09 00][00] v3.0.0.10 -> v4.1.0.0 need upgrade.
[00015508]Done.

[00017580]Waiting for user confirm...
[00027648]Timeout, start upgrade automatically.

[00027902]Firmware upgrading[1]...
[00027987][12 00] Firmware upgrade start...
[00085336][12 00] Firmware upgrade finished successfully.
[00085424][12 01] Firmware upgrade start...
[00144554][12 01] Firmware upgrade finished successfully.
[00144637][12 02] Firmware upgrade start...
[00205235][12 02] Firmware upgrade finished successfully.
[00205316][12 03] Firmware upgrade start...
[00261546][12 03] Firmware upgrade finished successfully.
[00261935][03 06] Firmware upgrade start...
[00653260][03 06] Firmware upgrade finished successfully.
[00653357][09 00] Firmware upgrade start...
[00705568][09 00] Firmware upgrade finished successfully.
[00705641]Done.

[00705716]Version checking[2]...
[00705841][03 06][05] v2.4.20.50 -> v2.4.20.50
[00705960][03 05][00] v34.2.0.9 -> v34.2.0.9
[00706042][04 00][00] v1.48.0.0 -> v1.48.0.0
[00706201][11 00][00] v1.8.0.0 -> v1.8.0.0
[00706359][11 01][00] v1.8.0.0 -> v2.0.0.33, firmware v1.8.0.0 not support.
[00706435][11 01][00] v1.8.0.0 -> v2.0.0.33
[00706549][12 00][05] v1.12.0.0 -> v1.12.0.0
[00706669][12 01][05] v1.12.0.0 -> v1.12.0.0
[00706800][12 02][05] v1.12.0.0 -> v1.12.0.0
[00706930][12 03][05] v1.12.0.0 -> v1.12.0.0
[00707096][15 00][00] v1.1.2.0 -> v1.1.2.0
[00707229][17 00][00] v1.1.1.7 -> v1.1.1.7
[00707384][17 01][00] v1.0.2.7 -> v1.0.2.7
[00707479][19 00][00] v1.0.8.96 -> v1.0.8.96
[00707555][01 00][00] v1.32.5432 -> v1.32.5432
[00707631][01 01][00] v1.32.5432 -> v1.32.5432
[00707723][08 00][00] v0.13.0.7 -> v0.13.0.7
[00707820][09 00][05] v4.1.0.0 -> v4.1.0.0
[00707894]Packet upgrade finish successfully.

Please try to reset the controller by holding C1, C2 and shutter button. Then refer the tutorial video to link RC again:

Thanks, Susan,

After holding C1, C2 and shutter button, controller beeps D - DD to confirm.

Try link procedure as video shows. it still can't link up.

SkyCamera Posted at 2017-8-31 21:34
Thanks, Susan,

After holding C1, C2 and shutter button, controller beeps D - DD to confirm.

Please start a case and send it in for diagnosis: http://www.dji.com/support.

hello everyone, i can not link the remote controller to the phantom 3 pro, i have tried everything with no luck, any suggestion please? thanks

Your mobile/tablet is connected to the TX as normal, AC is on but the LED's will just fast flash yellow... Go into the Go app,select relink tx from the Radio icon, - TX beeps - then press the button AC re-link button under side of the VPS, you have 90secs to do this or you have to restart - this will re-bind/link the tx and ac again.

Aerial-Image Posted at 2017-9-13 05:48
Your mobile/tablet is connected to the TX as normal, AC is on but the LED's will just fast flash yellow... Go into the Go app,select relink tx from the Radio icon, - TX beeps - then press the button AC re-link button under side of the VPS, you have 90secs to do this or you have to restart - this will re-bind/link the tx and ac again.

Tried many times, it doesn't work.

I updated my P3Adv with firmware v1.11.20 and somehow bricked the remote (I followed the DJI instructions, and have updated successfully before):

P3Adv camera light shows solid green after update.

DJI Go apps are up to date.

Remote originally showed solid green, now blinking red with beeps.  There seems to be no communicating with the remote.

Tried to update again without results using these methods: Tablet plug-in, android phone, thumb drive, micro SD, and direct plug into the drone port.

Tablet & phone method does not give options to update.  Only an error "Remote Controller not Calibrated".

Can you guys help me?  I'm really stuck here.

https://forum33.djicdn.com/data/attachment/forum/file:///C:/Users/Scott/Downloads/bricked.jpg

fansb7118541 I dunno if this will help but worked for me after the Go app updated despite, well you know the long tortuous story so.
fire it all up. RC, iPad(or whatever) & P3P. Go into DJI Go app and get to your usual flight screen (yeah I know it won't show anything and will be grey). Hopefully message will say craft disconnected.  So top left and between the DJI logo & touch the disconnected bar. With a bit of luck it should bring up an 'Aircraft Status' screen. There should be a red triangle against the overall status etc. select the triangle & follow instructions. But that's not all! If you continue tonget no image from the P3P shut it all down and remove the SD card from the
p3p. Restart without the SD card and with a bit of luck all should be working. And don't forget to reinsert the SD card later. Now if that doesn't work get some aluminium foil, make yourself a hat and run around shouting beep, beep, beep
Actually when I did the software upgrade all messages etc suggested all was good but for some reason the RC update then rolled back to a previous version. Hopefully one of the gurus can chip in and assist. Good luck.