Is the vibration gone? Is the camera invertion fixed? I really don't want to be the Guinea pig!  LOL I know it was just released so if anyone has a problem or maybe be they got it right!
I would sure like to hear about it.

THANKS

So I took the plunge,

Flew one battery, Did 7 landings.

3 of the 5 landings did wobble once landed until motors stopped. 2 of the landings didn't wobble.

However when it did wobble at first it didn't appear to be any different. then on closer inspection the  wobble didn't seem as violent as before. but no way to test this. Just visual opinion.

I then tried auto land, No Wobble either of the 2 times that I tried it.

Didn't notice any other issues in first flight either, Tried just flying in P, S & A then Tried Waypoints, All behaved as before.

Maybe this firmware was just the final release of the beta to correct the Inverted Video & Orange Pic which I did not have in previous release.

Therefore at this stage have not noticed any change from previous Firmware. In regards to landing It could be still the same as I didn't test as above with previous firmware, but can confirm that I did notice wobble landing in last firmware.

So at this stage at least I report no further issue's In fact the only previously reported issue still prevalent at least for me is the wobble upon landing, But in interim will use Auto land.

I only have had a few flights on .300 but had the impression that the High Wind Warnings was not so sensitive, from my one flight with .600 yesterday in near no wind i must say that they are back for sure, very annoying.
Beside that no downsides seen so far compared to .300 but still not as good as it was pre 4.0602.

I downgraded from .300 back to 602. Not much wobbling going on with fw 602. But videofeed lag remains. That is caused by the app

I'm still on the fence..... I'm still on ver 01.04.0602 . everything works still but I know sooner or later I'll have to upgrade. Trying to pick my poison.   

Edward J Smith Posted at 2018-3-9 08:19
I'm still on the fence..... I'm still on ver 01.04.0602 . everything works still but I know sooner or later I'll have to upgrade. Trying to pick my poison.

Me too...still on ver 01.04.0602 and very leery about making any changes

I updated and flew one battery, too dang cold for my tired old self to fly any more than that. I did all of the things that I had issues with before, everything appears to be good now. I tried out the pano feature, works great.

Just had one 15mins flight all seems perfect no problem at all on 1.05.0600 - From take off to landing , lots of functions tried & first go at the Pano function - all superb & perfect!

I just went through 3 batteries. 10km avg each flight. -5c outside. Zero issues. Everything was nice and smooth. Video was good on my iPad. I'm happy.

Mine is flying fine. No wobble.

Newbie here. Just flew first short flight yesterday morning after updating and had no issues at all.  Very smooth and great pics/video. P4P+obsidian.

I Just got a second P4P Obs (First one I upgraded to current F/W but returned it with gimbal shake). New P4P is running F/W V01.04.703. Flew it this morning with no issues. It should be a no brainer that I should now get it running latest firmware but the obvious DJI Dilema now is whether to upgrade F/W to get it up to date & take advantage of all the improvements and patches. But ... Is this going to ruin the thing?

Just flew with the new firmware as well, for me it was very stable and no issues. The inverted camera problem seems to have been fixed which was my biggest problem with the previous firmware. I RTH'd a few times using the button and turning off the controller, each auto control and landing was spot on.  The Pano photo modes worked every time as well, previously this was a bit hit and miss. There may have been a few tweaks to to the camera software as it seemed a tiny bit quicker in AEB, although this might just be new firmware placebo.

I forgot to pre-cache the maps and take the tablet off line, i'll try that next time. I fly within the VLOS (<500 m) rules so generally dont have issues with tx, no change so far, although I will do a range test when I can get observer help. I've also not imported any footage into Lightroom/Premier Pro so not closely inspected the footage either.

In summary, a very stable release for flight control, more testing required on the other stuff I've mentioned before I fully accept this a  go-to release, however, so far, so good.

fansdb6ff1f7 Posted at 2018-3-10 02:22
I Just got a second P4P Obs (First one I upgraded to current F/W but returned it with gimbal shake). New P4P is running F/W V01.04.703. Flew it this morning with no issues. It should be a no brainer that I should now get it running latest firmware but the obvious DJI Dilema now is whether to upgrade F/W to get it up to date & take advantage of all the improvements and patches. But ... Is this going to ruin the thing?

I too HAD the P4P-Obs on fw V 01.04.703 - upgraded it to the new 1.5.0600 - Its just fine to upgrade it will be ok. don't worry.... Images are fine in Lightroom - no weird colours - videos just fine in Premier - so all is good with this FW

Aerial-Image Posted at 2018-3-10 08:33
I too HAD the P4P-Obs on fw V 01.04.703 - upgraded it to the new 1.5.0600 - Its just fine to upgrade it will be ok. don't worry.... Images are fine in Lightroom - no weird colours - videos just fine in Premier - so all is good with this FW

I'm afraid I just don't trust the FW upgrades. I've had so many issues in the past (Mavic Pro/Inspire 2) when the things  fly and capture perfectly out of the box but never do once they get upgraded. Also I don't trust that rolling back the firmware, as I have done on numerous ocassions, really sets them back to a previous state.  Did you upgrade to 0600 in one step? rather than install each upgrade one at a time?

Yeah just 1 step from 1.04.070 to 1.05.0600

Do I have to upgrade I  series our can I jump to this new firmware?  Reason in asking is,  the update keeps failing/ freezing up.  I went to fly my new p4p for the third time and had no video feed.  Hence the attempt at these updates.

This one froze at 16%. So frustrating!

It does PAUSE while updating it takes a while  and the 5 mins it says it will take is actually more like 15-20 its does pause a few times from memory... but be patient and try again. I did it in one step straight to 1.05.0600 - the camera will do some odd movements - the LED's flash as it goes through the update , the thing to watch is the small led near the usb socket this just flashes red/green while updating and goes solid green when its complete. (PS - I updated on Windows10 machine.)

I did. Wobbling is still there unfortunately.

No issues here.

Updated (very reluctantly) this morning to 1.05.0600 and flew 2 batteries later in the afternoon.  Sun was setting and light was not very strong but still enough to fly and film at iso 200, f5,6, 1/100.   The issue I have is that after the update my php+ obsidian has problems focusing when in low light.    this is definitely something that wasn't happening before.

Anyone with the same issue?

I’m suddenly getting green screens and choppy video reception for the first time ever.  What makes it worse is I was out on some land that had absolutely nothing around it.  I traditionally fly in radio congested areas.  

method007 Posted at 2018-3-11 11:10
I’m suddenly getting green screens and choppy video reception for the first time ever.  What makes it worse is I was out on some land that had absolutely nothing around it.  I traditionally fly in radio congested areas.

Hi Method, try turning off video caching in DJIGO4.  Any chance you are using an iPad Mini 2?

Giammi Posted at 2018-3-11 04:06
I did. Wobbling is still there unfortunately.

I saw it too. Getting some strange behavior with the gimbal too. It drifts slowly. Reboot fixes it but it’s the first time I’ve ever seen it. I’m going to try again tomorrow. If it’s still there and I see that shake on landing, I’m rolling back.

Jeff

Any updates?  Trying to gauge whether or not to chance it.  

Really happy with 1.05.0600 so far -
  

Aerial-Image Posted at 2018-3-13 12:00
Really happy with 1.05.0600 so far -
  [view_image]

I'm happy with the update too, but haven't tried the Pano mode yet. Your photo - did you play with saturation, or did you use a UV filter (although light may have been too low for that to have had an effect)?

My experience is in this thread. I've rolled back to 01.05.0300 because the Gimbal is acting strange. I haven't flown due to the weather, but I can't see flying with the Gimbal drifting like it is.

Jeff

Punchbuggy Posted at 2018-3-13 13:38
I'm happy with the update too, but haven't tried the Pano mode yet. Your photo - did you play with saturation, or did you use a UV filter (although light may have been too low for that to have had an effect)?

Stock UV (Clear) filter - 180 Pano still image setting - 3:4 full frame - RAW image Colour- None -0.3EV under exposed - +5% Saturation & +5 Vibrance used In Lightroom ( https://www.aerial-image.co.uk/lightroom-preset/ ) just using my std -pop preset and a little bit of HSL and split-tone to boost what the camera raw image....so nothing added.