Please select Into the mobile phone version | Continue to access the computer ver.
Problems with firmeware 1.9.20 - PHANTON 3 Standart
1185 9 2019-9-29
Uploading and Loding Picture ...(0/1)
o(^-^)o
Anderson Machad
lvl.1
Flight distance : 5968 ft

Offline

Gentlemen,

I have a PHANTON 3 Standard aircraft and I'm in trouble.
The firmware update version 1.9.20 caused me serious problems with my aircraft, where any change I had wouldn't save, so I wouldn't have a chance, when I tried to change the image iso it wouldn't save. I had problems with constant image interference messages, everything related to the aircraft didn't really work.
The aircraft was not able to start the flight by the application and with a lot of difficulty I was able to lift the areonave, but the left direction of the control was inverted (I use it in mode 2) i.e.... when I put the aircraft to go up it went down.
I am currently using the version of the final 52 application.
I would like a technical opinion related to this failure of version 1.9.20, because I cannot understand the reason for the lack of functionality of my equipment.
It seems to me that the update you developed is programmed to discard the older aircraft as the update did not work properly on my aircraft. I imagine the people who acquired the same equipment and don't have the least amount of knowledge to solve it.
I am indignant and afraid of the upcoming firmware upgrades.
I had to revert the firmware to version 1.5.70, which apparently worked perfectly by flying for a few minutes and had no problems at all.
How far can I trust? Is there any instability in version 1.9.20?  I would like as an end user to know what I can expect from you.
Thanks.



2019-9-29
Use props
Roderick1976
New

Offline

Mr Anderson, I have the same problem the remote control did not work. I can only turn on the drone so that it lifts to 1.2 meters. How did you turn back the version? Could you pass it to me or tell me where I can download it. Thank you Regards. Roderick
2019-9-29
Use props
Roderick1976
New

Offline

255/5000 Mr Anderson, I have the same problem the remote control did not work. I can only turn on the drone so that it lifts to 1.2 meters. How did you turn back the version? Could you pass it to me or tell me where I can download it.
2019-9-29
Use props
Roderick1976
New

Offline

#Quick  255/5000 Mr Anderson, I have the same problem the remote control did not work. I can only turn on the drone so that it lifts to 1.2 meters. How did you turn back the version? Could you pass it to me or tell me where I can download it. Here#
2019-9-29
Use props
Roderick1976
New

Offline

[00708936]Firmware upgrading[1]...  [00709256][03 06] Firmware upgrade start...  [01119170][03 06] Firmware upgrade finished successfully.  [01119232][09 00] Firmware upgrade start...  [01162134][09 00] Firmware upgrade finish without reboot.  [01192174][09 00] Firmware upgrade finished successfully.  [01192252][04 00] Firmware upgrade start...  [01250721][04 00] Firmware upgrade finished successfully.  [01250761]Done.   [01250805]Version checking[2]...  [01250884][03 06][05] v2.4.20.50 -> v2.4.20.50  [01250931][04 00][05] v1.51.0.0 -> v1.51.0.0  [01251035][09 00][05] v0.1.1.1 -> v0.1.1.1  [01251079]Packet upgrade finish successfully.     [00014287]========== remo-con disconnect. boot(15) ============  [00014345]Packet [C:\P3C_FW_V01.09.0200.bin] detected, card sn [0x354e0f5e].  [00014411]Packet upgrade start...   [00014464]Packet checking...  [00014502]Packet vlink 01.09.0200 <-> 00.00.0000.  [00014550]Record vlink 01.09.0200 <-> 00.00.0000 (flow = 0).  [00014589]Done.   [00014624]Version checking[1]...  [00014665][04 00][00] v1.51.0.0 -> v1.51.0.0  [00014790][11 00][00] v1.8.0.0 -> v1.8.0.0  [00014909][11 01][00] v1.8.0.0 -> v2.0.0.33, firmware v1.8.0.0 not support.  [00014955][11 01][00] v1.8.0.0 -> v2.0.0.33  [00014990][01 00][00] v1.14.4920 -> v1.14.4920  [00015025][01 01][00] v1.14.4920 -> v1.14.4920  [00015105][03 05][00] v34.2.0.9 -> v34.2.0.9  [00015188][03 06][00] v2.4.20.50 -> v2.4.20.50  [00015268][07 00][00] v1.0.9.65 -> v1.0.9.65  [00015321][09 00][00] v0.1.1.1 -> v0.1.1.1  [00015428][12 00][00] v5.9.0.0 -> v5.9.0.0  [00015513][12 01][00] v5.9.0.0 -> v5.9.0.0  [00015629][12 02][00] v5.9.0.0 -> v5.9.0.0  [00015728][12 03][00] v5.9.0.0 -> v5.9.0.0  [00015764]Packet upgrade cancelled at version checking.
2019-9-29
Use props
Anderson Machad
lvl.1
Flight distance : 5968 ft

Offline

Roderick1976 Posted at 9-29 10:02
#Quick  255/5000 Mr Anderson, I have the same problem the remote control did not work. I can only turn on the drone so that it lifts to 1.2 meters. How did you turn back the version? Could you pass it to me or tell me where I can download it. Here#

Hello, gentlemen,
I downloaded the firmeware through this link.
https://forum.dji.com/thread-104293-1-1.html
The procedure I performed was to copy the 1.5.70.bin file to the memory card and restart the aircraft with the remote control on... it will sound like the beeper is fully charged from the aircraft and the control.
To assist in the update sound, follow a link that helped me. It is worth remembering that I did not update by the application, only by the memory card.
Video link
https://www.youtube.com/watch?v=ysW8sW0Xnos
Manual for help related to the final result.
I didn't follow the update manual either, I just used it to help me with the final result of the beeps...
Beep with the green light on continuously and the beeper... pi-pipi indicates that it has been successfully updated.
Beep with the red light on steady and the beeping constantly indicates that there has been a failure to update.
I had some flaws because I was trying to use the same version, but... but after I did it with the informed version, I was successful.
If it is successful, don't forget to format the card!
I hope it helps!
If it works... come back here to give us the answer.

Good luck!
2019-9-29
Use props
Anderson Machad
lvl.1
Flight distance : 5968 ft

Offline

Anderson Machad Posted at 9-29 18:10
Hello, gentlemen,
I downloaded the firmeware through this link.
https://forum.dji.com/thread-104293-1-1.html

Manuals
http://dl.djicdn.com/downloads/phantom_3_standard/P3S_Firmware_Update_Guide_en.pdf
2019-9-29
Use props
Peterx
Captain
Flight distance : 1499708 ft
Offline

I use the P3S with the 1.09.0200 nearly a year and had no trouble at all. After the upgrade i checked all settings of the bird and did a calibration of the IMU and RC sticks only. That was it.
The bird is flying as expected.
2019-9-30
Use props
Anderson Machad
lvl.1
Flight distance : 5968 ft

Offline

To get an idea of the problem, I couldn't see the version of the firmware and the serial number of the aircraft by the application.
2019-9-30
Use props
Peterx
Captain
Flight distance : 1499708 ft
Offline

Do you have any telemetry on the screen in the app?  ...any serial of your RC or AC? ....any feed from the AC´s cam? If not then you may have a connection problem between your RC/AC and your mobile.
Did you connect your RC/AC to your mobile via WIFI yet?
2019-9-30
Use props
Advanced
You need to log in before you can reply Login | Register now

Credit Rules