How do I correct a slight left/right gimbal tilt on the Inspire with X3? Can't identify anything in the menu for that specific  function. All firmware up to date.

Go to the "General settings" on the Go App  and then go to the Camera Icon "Gimbal Settings"  Here you will find the "Adjust Gimbal Roll"  setting.  

I usually like to set myAircraft into a nice stable  Hover in very light if any wind and then get the Horizon in view and adjust tolevel , At first I did it with the Aircraft on the ground but found that Level on the ground is different then level in the air ( Lots of factors here )  So i get better results this way , Of course you  may have a differ net opinion, just my 2 cents.

**see post 3 and 4 as well for other ways to skin this cat !!

donnie  

I've got the I1P so I'm not sure this is workable with the X3 but, during flight, or on the ground for that matter, you can hold down C2 and move the right dial to adjust your horizon. I'm not sure is this is even documented anywhere. I just stumbled on it a few weeks ago.

flighttime1 Posted at 2016-5-18 13:53
I've got the I1P so I'm not sure this is workable with the X3 but, during flight, or on the ground f ...

flightitme , C1 and C2 can be programmed to do lots of different functions , you can find this under the Remote Control settings of the Go app.

You may already know this, just a friendly reminder if not .

donnie

Donnie Posted at 2016-5-18 12:05
flightitme , C1 and C2 can be programmed to do lots of different functions , you can find this und ...

Donnie. I believe this functionality is hard coded as I said, it's a two step process. As far as I know, you can only program simple action/response functions in C1 C2. I say that becuse right now, C2 is 'programmed' to reset the gimbal on my bird. Again, I'm not aware this is documented anywhere and would appreciate if folks would give it a try and report back.

flighttime1 Posted at 2016-5-18 11:53
I've got the I1P so I'm not sure this is workable with the X3 but, during flight, or on the ground f ...

Thanks for the tip that's cool

flighttime1 Posted at 2016-5-18 14:13
Donnie. I believe this functionality is hard coded as I said, it's a two step process. As far as I  ...

I just tried it and it works, I dont have my C1 or C2 defined either.  I learned something today,  I also like the "Green reference lines " for level.....cool !!
I know there are some other functions that are hidden as well, I need to write these down for sure !!

Thanks,

donnie

Donnie Posted at 2016-5-18 12:30
I just tried it and it works, I dont have my C1 or C2 defined either.  I learned something today,  ...

Donnie. Maybe I picked up a few 'good guy' points with you today.

flighttime1 Posted at 2016-5-18 14:32
Donnie. Maybe I picked up a few 'good guy' points with you today.

You certainly did,  Thanks again!!

donnie

str1776 Posted at 2016-5-18 14:28
Thanks for the tip that's cool

Be sure to try it, the green reference line is very cool, gives one for Vertical and Horizontal !

Love it !!

Donnie

The refrig cold IMU calibration helps a ton and fix the issue as well until the next time you update.

Donnie Posted at 2016-5-18 20:35
Be sure to try it, the green reference line is very cool, gives one for Vertical and Horizontal !
...

What is this magic green reference line of which you speak,please?  And where/how would I find it,please?  

Nigpd Posted at 2016-5-21 02:50
What is this magic green reference line of which you speak,please?  And where/how would I find it, ...

While the Rig is up and flying press the C2 button on back of RC ,  and the Right Iso wheel,  ( same time ) then you will see the magic green lines, you can then adjust with the wheel
Or follow post #3 directions, that is where I got it .  

donnie

flighttime1 Posted at 2016-5-18 14:53
I've got the I1P so I'm not sure this is workable with the X3 but, during flight, or on the ground f ...

Hat tip-flighttime 1!  Works with my X3.
Much easier than pulling it up on the app and displaying on the screen.  No more tap,tap,tap.
Thanks,
60

Interesting update. I use Autoflightllogics Autopilot quite a bit and attempted to do a horizon adjustment while that app was open the other day and... Nothing. So it seems this is actually coded into the DJI Go app and not part of the R/C -> Inspire connection. Now I'll need to do further testing to see if adjustments made remain as part of the calibration or are just for the individual flight or even just when using the DJI Go app.

Donnie Posted at 2016-5-21 11:02
While the Rig is up and flying press the C2 button on back of RC ,  and the Right Iso wheel,  ( sam ...

thanks Donnie

flighttime1 Posted at 2016-5-18 12:13
Donnie. I believe this functionality is hard coded as I said, it's a two step process. As far as I  ...

You are correct using the C2 button you can use the right trim wheel to adject the gimbal. You can use the C1 button and the right trim wheel to adjust the camera EV. These are hard coded because I have these buttons defined on my remote for other tasks.
screen shot below showing the gimbal adjust crosshairs.





Rich

Nigpd Posted at 2016-5-21 00:50
What is this magic green reference line of which you speak,please?  And where/how would I find it, ...

posted screen shot

Rich

Thanks Rich

When I read this thread, I was sure I saw this documented, and it's hidden on page 38 (of 66) of the Inspire 1 User Manual v2.0 dated 2015.11
Under Camera Gimbal section, a single liner.

"while pressing the C2 button, turn the camera settings dial to fine tune the roll axis of the gimbal.

Chris G Posted at 2016-5-27 08:15
When I read this thread, I was sure I saw this documented, and it's hidden on page 38 (of 66) of the ...

Good find, at least some of us made it to page 38!
The manual has a lot of good information and it is hard to remember all this stuff.  


Rich

Chris G Posted at 2016-5-27 08:15
When I read this thread, I was sure I saw this documented, and it's hidden on page 38 (of 66) of the ...

Are you saying I don't read manuals?

Chris G Posted at 2016-5-27 10:15
When I read this thread, I was sure I saw this documented, and it's hidden on page 38 (of 66) of the ...

     The problem is some of the earlier manuals did not explain this , I think it actually came out with one of the updates, and then it did not explain that there would be some nice green reference lines as well,  so everyone is right really, I am just glad that Flightime brought this to my attention.

And Chris G you made me realize that I must read the updated manuals every few months to make sure I am getting full benefit of my aircrafts capabilities.   Thanks !

cheers-
donnie

flighttime1 Posted at 2016-5-18 11:13
Donnie. I believe this functionality is hard coded as I said, it's a two step process. As far as I know, you can only program simple action/response functions in C1 C2. I say that becuse right now, C2 is 'programmed' to reset the gimbal on my bird. Again, I'm not aware this is documented anywhere and would appreciate if folks would give it a try and report back.

amazing find, the power of the internet!

RichJ53 Posted at 2016-5-27 08:57
Good find, at least some of us made it to page 38!
The manual has a lot of good information and it is hard to remember all this stuff.  

What are other things that are good tips like this?

AntDX316 Posted at 10-6 16:29
What are other things that are good tips like this?

This has been around now for a long time. Most everything is documented on Youtube.  

It was contently changing as the FW updates were released and the Go app was updated by DJI...

Rich