Phillips #000 or #00 will work fine.  The #00 will be a the best fit IMO Sorry do know what the replacement screw would be.. thought you were looking for the best screwdriver.  You might need to buy a replacement mount kit to get that part sorry to say.
Rich

Hi Guys. Can anyone tell me what size or name these two screws are in the picture
Not sure the size but  there names are , " Lucy "  and "Philip"   

Sorry could not resist , just take the one out that you do have and take it to the hardware store .  

donnie

Donnie Stugots Posted at 2017-1-4 09:33
Hi Guys. Can anyone tell me what size or name these two screws are in the picture
Not sure the size but  there names are , " Lucy "  and "Philip"   

funny...  

The problem is the tread pitch could be anything. I noticed that most metric screws used in camera's or drones are not a consistent even number. 1.2 mm, 1.1mm  or 1.4mm  This could be tough to find without DJI telling us the screw size
Rich

RichJ53 Posted at 2017-1-4 10:20
funny...  

The problem is the tread pitch could be anything. I noticed that most metric screws used in camera's or drones are not a consistent even number. 1.2 mm, 1.1mm  or 1.4mm  This could be tough to find without DJI telling us the screw size

I would take the other one out that he still does have and the measure it with a dial caliper .  I do agree with you that if DJI could provide the specs, that would be great.

donnie

Donnie Stugots Posted at 2017-1-4 10:23
I would take the other one out that he still does have and the measure it with a dial caliper .  I do agree with you that if DJI could provide the specs, that would be great.

donnie

Yes, if you could find some hobby store that carries spare screws. I have a huge supply of helicopter screws from many brands which none are the same

but at least the sizes are listed by the manufacture. It would be nice if DJI did the same for all of there drones too.

Rich

Hi Richard,

If you only need the one screw, I can spare one and would be happy to post it to you. Just PM me your address and I'll stick it in an envelope for you. I'm in the UK so could have it to you in a day or two.

Mark G.

Donnie Stugots Posted at 2017-1-4 09:33
Hi Guys. Can anyone tell me what size or name these two screws are in the picture
Not sure the size but  there names are , " Lucy "  and "Philip"   

Donnie! Have you been on the 'sauce' again?

Hardware store probably won't go that small.
Take it to a Hobby shop.

RichardHurst Posted at 2017-1-4 12:13
Hi Mark

I've seen I can get them online. This is the part I really need to try and find as the screw has sheared off in it and can't get it out.

Check this out on eBay for parts

http://www.ebay.com/itm/DJI-Insp ... :g:vnQAAOSwcUBYRfh~

Rich

RichardHurst Posted at 2017-1-4 12:38
Shame its not in the UK, that will cost me way to much to get sent here

I will take a look. I may have that piece spare.

Mark Guille Posted at 2017-1-4 10:50
Donnie! Have you been on the 'sauce' again?

He said "Can you name these Screws "

So I named them ,

Next time I will call them   "Jack  &  Danial "

Hit me again bartender , one for the road !!!
***PS : Very nice of you Mark to help him out , you are a good mate .

donnie

Mark Guille Posted at 2017-1-4 13:02
I will take a look. I may have that piece spare.

Wow that's nice Mark!!

You will be a savior for sure.  I did not see this part listed anywhere but I am glad you have one.  

All the best
Rich

RichardHurst Posted at 2017-1-4 13:50
Mate you would be a life saver if you have.

I have a few spare parts from DJI of this sort. PM me if Rich hasn't. I can email you the part. They cost like USD 2 for the rubber and two screws.

RichardHurst Posted at 2017-1-5 00:26
Thanks Mike. It's the top part f the gimbal that is really needed and then I can get the new screws and rubber piece

The part you need is listed on this page http://www.helipal.com/multi-rot ... _dji-inspire-1.html
You might want to order other goodies from them. Best use the original parts.

Mike-the-cat Posted at 2017-1-5 01:41
The part you need is listed on this page http://www.helipal.com/multi-rotors_spare-parts_dji-inspire-1.html
You might want to order other goodies from them. Best use the original parts.

Wow , loved that resource , thank you for sharing Mike...... brilliant

donnie

RichardHurst Posted at 2017-1-5 01:56
Hi Mike. I can see the rubber gasket and screws on there but it's the bit that this sits on I need, Pic above. Cannot see that on the website

Uh-oh - looks like you have deal with DJI directly on this matter. How did this damage occur?

Hey Richard, I may have the top part and/or screws (and I'm in the UK )
let me check this evening and I'll let you know..

Ta-da!
(It still has a gimbal part attached to the base - ignore that, I just haven't removed it yet )

PM me your address and I'll pop it in the post with a couple of screws

The beauty of when the forum community comers together......I love it

donnie

Hi Richard,

I have taken the part off my spare X3 and PM'd you but it looks like you may have been sorted. PM me if you still need it as it's sitting in an envelope waiting to be posted.

Mark G.

It's on the way Richard (& Mark!)

Argh! I'm so sorry Richard. It's all I had in my parts box and I didn't realise there was a difference - I have X3, X5 and X5R parts in there.

It looks from your description as though the X3 uses 3 screws through that part to the yaw gimbal, whereas the X5 and X5R use a spacer plate, held on by four bolts into the bottom of it. I'd thought this was X2 but clearly it's not and there's an important difference in the mounting