Mine is reading 1.0.14 with 3.1.3 app.

Sorry, this was supposed to have been in the P3s section.

Could you verify what Phantom version you have?

fans2191ca76 Posted at 2017-2-18 17:38
Sorry, this was supposed to have been in the P3s section.

Is yours a P3std? you can check here http://www.dji.com/phantom-3-standard/info#downloads
Also you are still using the samsung S7?
Edit.....See below post for the latest, Thanks for the correction blackcrusader

Nigelbrinkmann Posted at 2017-2-18 18:12
Is yours a P3std? if so v1.4 is the latest, but you can check here http://www.dji.com/phantom-3-standard/info#downloads

Latest Firmware is 1.8.0  I bought a new battery and it had to be upgraded.

blackcrusader Posted at 2017-2-18 18:14
Latest Firmware is 1.8.0

Sorry my bad will correct post!

DJI-Jamie Posted at 2017-2-18 18:07
Could you verify what Phantom version you have?

Phantom 3 standard

fans2191ca76 Posted at 2017-2-18 18:29
Phantom 3 standard

It's 1.8.0, like others mentioned.

DJI-Jamie Posted at 2017-2-18 18:51
It's 1.8.0, like others mentioned.

So why does mine say 1.0.14?

fans2191ca76 Posted at 2017-2-18 19:20
So why does mine say 1.0.14?

Did you update the firmware on your unit recently and still have 1.0.14 on your About page?

DJI-Jamie Posted at 2017-2-18 19:24
Did you update the firmware on your unit recently and still have 1.0.14 on your About page?

I think ive only updated the firmware onentime since ive bought it december 1 2016.  Never had an issue withnit until this last go update.

fans2191ca76 Posted at 2017-2-18 19:43
I think ive only updated the firmware onentime since ive bought it december 1 2016.  Never had an issue withnit until this last go update.

Is the app asking you to update? What kind of issues are you experiencing?

I would do a firmware upgrade as there are important changes that have been addressed.

DJI-Jamie Posted at 2017-2-18 19:51
Is the app asking you to update? What kind of issues are you experiencing?

So starting up, i turn on the controller, craft, then open wifi and connect to the craft, then open the app.

When the app opens, it is constantly switching between a pic of the mavic and phantom 3 standard enter camera section.  It brought up the inspire one time and it actually created a flight log.

I have to time the switching to be able to enter the p3s camera.  When i enter, the camera is either very bad laggy or not on at all.

In the upper middle section where it usually says warming up, it has been saying weak transmission signal, disconnected, or weak controller signal.

I also am not getting my maps.  I have tried with and without airplane mode and i have cleared my apps cache.  I have tried to reconnect the controller and all the lights work appropriately.

Are you doing this inside a building?

blackcrusader Posted at 2017-2-19 04:53
Are you doing this inside a building?

Outside in my yard.  No concrete, no metal surfaces, open field type of yard.

DJI-Jamie Posted at 2017-2-18 19:51
Is the app asking you to update? What kind of issues are you experiencing?

Its not asking me to update.  

fans2191ca76 Posted at 2017-2-19 19:41
Its not asking me to update.

If you have the latest version of the Go app and you and the connection to even get into camera view is difficult, it could be a problem with the built in WiFi module. If you havan't already, I would try the following to absolutely rule it out:

- Completely 'forget' the P3S' WiFi from your device's list and then refresh the connection
- Try a different mobile device.

If the issue persists, I would recommend sending the unit in for service. If you just got the aircraft from a dealer, you may want to look into getting an exchange.

DJI-Jamie Posted at 2017-2-21 15:45
If you have the latest version of the Go app and you and the connection to even get into camera view is difficult, it could be a problem with the built in WiFi module. If you havan't already, I would try the following to absolutely rule it out:

- Completely 'forget' the P3S' WiFi from your device's list and then refresh the connection

I think ive discovered the problem.  I had DJI Gonfor my phantom and DJI Go 4 for my mavic on the same phone.

I put DJI Go on my sons phone and it works perfectly.

fans2191ca76 Posted at 2017-2-21 16:39
I think ive discovered the problem.  I had DJI Gonfor my phantom and DJI Go 4 for my mavic on the same phone.

I put DJI Go on my sons phone and it works perfectly.

Good to hear you were able to sort it out.