Please select Into the mobile phone version | Continue to access the computer ver.
Firmware Update Failure
8799 18 2015-3-8
Uploading and Loding Picture ...(0/1)
o(^-^)o
thefletch3d.gma
lvl.1

United States
Offline

Hey Guys,

Went to do a firmware update and followed the instructions.  About half way through the inspire started beeping long beeps and wouldn't stop.  The txt file said failure.  I tried the update again and it just sits there with the yellow lights flashing, no beeps, not updating.  Now the TX will not link up with the aircraft?

Not sure what to do from here.  I have tried several times to update, Yes I did remove the TXt failed file hoping that had something to do with it.

HELP
2015-3-8
Use props
stoneyphil
lvl.1

United Kingdom
Offline

I had the same problem with the remote, I sent a message on the Inspire chat support and they sent me a file, this worked and I'm back flying
2015-3-8
Use props
stuzphotos
lvl.1

United States
Offline

stoneyphil Posted at 2015-3-9 02:24
I had the same problem with the remote, I sent a message on the Inspire chat support and they sent m ...

Can you please send me the file
Thanks Stu
2015-3-8
Use props
bernd.gillnetwo
lvl.1
Flight distance : 278914 ft
  • >>>
Germany
Offline

stoneyphil Posted at 2015-3-9 02:24
I had the same problem with the remote, I sent a message on the Inspire chat support and they sent m ...

Hi I have the same problem.
Can you send methefile?

Best regards

Bernd
2015-3-9
Use props
stoneyphil
lvl.1

United Kingdom
Offline

Hi If you send me your e-mail address I'll forward it on and the instruction I received
2015-3-12
Use props
Fencinales
lvl.1

Colombia
Offline

stoneyphil Posted at 2015-3-13 00:08
Hi If you send me your e-mail address I'll forward it on and the instruction I received

I have the same problem. My email is fencinales@inverlink.com

I would appreciate if you could send me the file you got from DJI

Tks

Fencinales
2015-3-12
Use props
stoneyphil
lvl.1

United Kingdom
Offline

Hi Fencinales I have sent you the GS file and instruction
2015-3-12
Use props
daniel
Flight distance : 1392028 ft
  • >>>
United States
Offline

I have the same problem how did you guys fixed it?

2015-3-15
Use props
FlyingSquirrel
lvl.4
Flight distance : 17141325 ft
  • >>>
Argentina
Offline

Hi guys I have the same problem! please help me I have a job in a couple of days and Im stressing hard!  my email leniekw@gmail.com ... can you send me the file so I can try that solution? Thank you!!
2015-3-17
Use props
Tahoe_Ed
Captain
Flight distance : 2605 ft
  • >>>
United States
Offline

Here is the link to the GS bin file that will cure bricked Tx's.  Run the file and after success then on a freshly formatted USB drive with the v.17 bin installed inserted in the USB port, start the Tx.  You should progress through the upgrade.

https://www.dropbox.com/s/0suyxxhm5g5g6or/gs_ofdm.bin?dl=0
2015-3-17
Use props
aumike
lvl.1
Flight distance : 107116 ft
United States
Offline

Tahoe_Ed Posted at 2015-3-18 07:58
Here is the link to the GS bin file that will cure bricked Tx's.  Run the file and after success the ...

Does this fix a bricked Inspire craft (not the Tx)?  Waiting to hear by from support, but its been 3 days with no update.  I tried to update my brand new inspire and get the constant beep after 10 minutes; text file says update failed.  Online support said I probably needed a new cam.  Bird has never been off the ground
2015-3-18
Use props
Tahoe_Ed
Captain
Flight distance : 2605 ft
  • >>>
United States
Offline

aumike Posted at 2015-3-19 10:47
Does this fix a bricked Inspire craft (not the Tx)?  Waiting to hear by from support, but its been  ...

That bin file is only for the Tx.  The procedure for a bricked Inspire is different.  First replace the gimbal and if that does not work replace the MC.  Neither of which are user serviceable items.  Well you could try a different gimbal if you have a spare sitting around or a friend that will loan you theirs.
2015-3-18
Use props
aumike
lvl.1
Flight distance : 107116 ft
United States
Offline

Tahoe_Ed Posted at 2015-3-19 11:31
That bin file is only for the Tx.  The procedure for a bricked Inspire is different.  First replac ...

Thanks.  No spare gimbal or friends with gimbals to try.  Guest my $3,400 paperweight will continue to sit and mock me.  With no response from support, I'm going to call UAV Direct, whom I purchase from, and try for a replacement.
2015-3-18
Use props
thefletch3d
lvl.1

United States
Offline

I ended up figuring out through support that my tx USB port had failed and sent the tx in for service.  Will know in about 4 to 6 weeks if I ever get it back. The support for inspire 1 is horrible at best.  My aircraft went through the update and then just sat there flashing.  I sent support my failed logs and they said it finished the update, but got hung up on the reboot.  I have flown it and it flies great.
2015-4-3
Use props
davy.bernaerts
New

Belgium
Offline

Hi guys, i had a problem with updating my inspire for the first time!
I guess i did something wrong with the first update and i had to abort installation.
When i try to do this update again, i get no response exept the red tail light.
PLEASE HELP!!
2015-4-18
Use props
adam.plvisuals
New

United States
Offline

I had the problem and got it to work. I tried updating firmware and I would get the blinking yellow lights and nothing else. Finally I decided to fly it with current firmware instead but left the card in the bird with the firmware. When I turned it on with the controller ready to fly, it started the 4 low beep sequence and i soon realized it was updating. After it finished beeping about 15-20 minutes later, i checked it and it was updated. Looks like I had to turn on the bird and the controller for it to catch (even though the instructions say to leave the controller off).
2015-8-17
Use props
7209459
lvl.1

Russia
Offline

Tahoe_Ed Posted at 2015-3-19 11:31
That bin file is only for the Tx.  The procedure for a bricked Inspire is different.  First replac ...

Is it exist file for repair camera of inspire?
LOG:
[00994489][15 00] Firmware upgrade finish failed (step = 5, err = 0xff, sum = 0xcc08).

[01142076]Version checking[3]...
[01142113][01 00][05] v1.19.3422 -> v1.19.3422
[01142148][01 01][05] v1.19.3422 -> v1.19.3422
[01142199][03 05][00] v34.1.0.5 -> v34.1.0.5
[01142319][03 06][05] v2.2.6.33 -> v2.2.6.33
[01142359][04 00][05] v1.26.0.3 -> v1.26.0.3
[01142440][05 00][05] v3.0.6.1 -> v3.0.6.1
[01142489][08 00][05] v1.14.0.25 -> v1.14.0.25
[01142535][09 00][05] v1.8.0.0 -> v1.8.0.0
[01142600][11 00][05] v3.7.15.9 -> v3.7.15.9
[01142680][12 00][00] v1.8.0.0 -> v1.8.0.0
[01142780][12 01][00] v1.8.0.0 -> v1.8.0.0
[01142880][12 02][00] v1.8.0.0 -> v1.8.0.0
[01142962][12 03][00] v1.8.0.0 -> v1.8.0.0
[01152344][15 00][06] device not detected.
[01152399][17 00][05] v1.1.0.4 -> v1.1.0.4
[01152519][17 01][05] v2.0.0.8 -> v2.0.0.8
[01152563][19 00][00] v1.0.8.96 -> v1.0.8.96
[01152597]Packet upgrade failed at version checking.

[00004452]========== remo-con disconnect. boot(15) ============
[00004486]Packet [C:\WM610_FW_V01.03.00.00.bin] detected, card sn [0x50ce3e64].
[00004525]Packet upgrade start...

[00004562]Packet checking...
[00004605]Packet vlink 01.03.0000 <-> 01.02.0000.
[00004679]Done.

[00004736]Version checking[1]...
[00004780][01 00][00] v1.19.3422 -> v1.19.3422
[00004838][01 01][00] v1.19.3422 -> v1.19.3422
[00004910][03 05][00] v34.1.0.5 -> v34.1.0.5
[00004997][03 06][00] v2.2.6.33 -> v2.2.6.33
[00005044][04 00][00] v1.26.0.3 -> v1.26.0.3
[00005110][05 00][00] v3.0.6.1 -> v3.0.6.1
[00005163][08 00][00] v1.14.0.25 -> v1.14.0.25
[00005215][09 00][00] v1.8.0.0 -> v1.8.0.0
[00005310][11 00][00] v3.7.15.9 -> v3.7.15.9
[00005411][12 00][00] v1.8.0.0 -> v1.8.0.0
[00005510][12 01][00] v1.8.0.0 -> v1.8.0.0
[00005611][12 02][00] v1.8.0.0 -> v1.8.0.0
[00005790][12 03][00] v1.8.0.0 -> v1.8.0.0
[00018338][15 00][00] device not detected.
[00018410][17 00][00] v1.1.0.4 -> v1.1.0.4
[00018510][17 01][00] v2.0.0.8 -> v2.0.0.8
[00018560][19 00][00] v1.0.8.96 -> v1.0.8.96
[00020596]Packet upgrade failed at version checking.
2015-8-23
Use props
Tahoe_Ed
Captain
Flight distance : 2605 ft
  • >>>
Hong Kong
Offline

What the txt file is telling you is that the Air End USB transmitter is not being detected.  Try to format the card and do a clean install of the bin file.  It that does not work then you will have to open ticket and send the P3 in for repair.
2015-8-24
Use props
fans95bfecb2
New

United States
Offline

Any one with the problem after interrupted the firmupgrade?
Now I've got long beep and not doing anything
2018-3-3
Use props
Advanced
You need to log in before you can reply Login | Register now

Credit Rules