Seestreicher Posted at 2016-6-19 21:22
Main Controller Connection to Center Board Failed
Gimbal cannot receive Main Controller date

Hi Bernhard
I have the same problem.
Did you get an solution?

new firmware 1.9.1 seems to act weird : Red led on RC and discontinued bip.
no problem on flying so far...

Henry Mo-Yung Posted at 2016-7-1 14:59
Hi, Linolens,

I confirm I also received the same email which appeared to me from DJI. I have sent a ...

Hi Henry,
I've got confirmation these are ok.
I'll update this weekend as I have a job to do.
Hopefully it'll be all good.

nilsblix@gmail. Posted at 2016-7-1 14:58
I also got a email with attached Fw file for my Inspire. I am on travel and it will be some days unt ...

Hi nilsblix,
I did get confirmation it's from DJI.
Will update this weekend and test it out

Hope the new internal firmware solves the issues. Please keep us updated!

Henry Mo-Yung Posted at 2016-6-20 01:58
Hi Donnie,

I'd checked all sensors' MOD values before flight and all were normal - Gyroscope 0.0 ...

Mine did the same thing on firmware 1.9 Henry. Luckily I had read this thread so I identified the faults as soon as they happened. Was hard to land softly the first time as it was descending on its own. Have downgraded to 1.8 until they fix the bugs. Have never had any problems with the inspire until this latest update

I had also done imu, gimbal, compass calibration and stick calibration as I do after every firmware update. Landing was stuck down too

brendanabbott@h Posted at 2016-7-1 21:45
I had also done imu, gimbal, compass calibration and stick calibration as I do after every firmware  ...

Hi Brendanabbott,

The issues were intermittent - I first encountered the issues twice amongst several normal flights on 19 Jun 2016. One week later, after completing IMU calibration I carefully flew the I1Pro - no issue at all during the several flights on 25 & 26 Jun 2016. Today I encountered the issues again, exactly the same uncommanded climbing without autoraising landing gear. I have not downgraded and am still at FW v1.09.01.10 at this moment.


It seems to me DJI has been working hard in diagnosing and addressing the issues - I received an email from DJI with hyperlinks pointing to two files referred as "internal firmware" for Inspire 1 & Inspire 1 Pro respectively. I downloaded the 2 files and am considering upgrading.

Will provide any findings upon completion of upgrading with the "internal firmware" and test-flying.

Henry

vincentlublink@ Posted at 2016-6-30 21:31
thake the update of from the website before more people have issues withe the latest update!!!!

But to do that would mean an admission something is wrong which DJI as a Chinese company is culturally incapable of doing.

It will be 'Fixed' but nothing was ever 'wrong' in the first place

I just called DJI and they are unaware of any "internal firmware.".........  Just thought I'd check on it.

Hi Folks,

I have upgraded my I1 Pro with the "internal firmware" from DJI Support Team and tested it out in this morning with 4 packs of batteries (8 taking-offs & 8 landings). I would like to advise that the I1 Pro with the "internal firmware" consistently performed as it should be, with both X3 & X5 attached.

I am looking forward to DJI's official release of the firmware after DJI has received further feedbacks from other Fellow I1 Owners to whom DJI sent these "internal firmware" and from their own tests.

In the mean time, I wish all who upgraded to FW v1.09.01.10 good luck!

Happy and safe flying!

Henry

Linolens Posted at 2016-7-1 16:42
Hi Henry,
I've got confirmation these are ok.
I'll update this weekend as I have a job to do.

Thank you, Lino.

Without your advice on the confirmation from DJI in relation to the authenticity of the email and the 2 "internal firmware" files, I might still be hesitating to upgrade the firmware.

It appeared to me you had edited your post several times, didn't you? Were you asked to do so?

Nevertheless, I hope we all will soon receive the official firmware release from DJI. A lot of folks here need it.

Henry

Henry Mo-Yung Posted at 2016-7-1 20:03
Hi Folks,

I have upgraded my I1 Pro with the "internal firmware" from DJI Support Team and tested i ...

Henry
thank you for reporting back your findings   It is good to hear they have worked correctly on your Inspire 1 with both cameras. I wonder how long it is going to take before they release the FW as I have downgraded mine even though it was not acting up. I have noticed during filming this week the inspire would sink several feet by itself and I held up-stick to keep it in one place.   It has never done that before

Rich                  

RichJ53 Posted at 2016-7-2 12:34
Henry
thank you for reporting back your findings   It is good to hear they have worked correctly o ...

Hi Rich,

The FW upgrade processing from FW v1.09.01.10 to the DJI's supplied "internal firmware" only took less than 5 minutes, and in fact only device [17 00] was upgraded. I have no idea on which device in the Inspire 1 this device [17 00] is, but my observations in this morning's tests after the upgrade were that the Inspire 1 Pro held altitude quite well - rock solid as before.

I remember in FW v1.08.01.00 my Inspire 1 Pro did change altitude sometimes, and I thought it was due to windy condition. Please see my case in this post. inspire rising or lowering when landning gear changed

Henry

Henry Mo-Yung Posted at 2016-7-2 06:12
Thank you, Lino.

Without your advice on the confirmation from DJI in relation to the authenticity  ...

Thank's for the update, Henry!

Hope we others get the frmware really soon, too. My Inspire is grounded until it arrives.

Have a nice weekend everyone!

Linolens Posted at 2016-7-1 04:55
TB48
Do you think there's a connection there?

Not sure, tried to fly this morning, and had the same happen. Used the TB47 though.

Henry Mo-Yung Posted at 2016-7-2 01:17
Hi Brendanabbott,

The issues were intermittent - I first encountered the issues twice amongst sev ...

Thanks Hennry. I had done an imu calibration on mine, compass calibration, stick calibration and also pre flight check of all values after the update (standard procedure I follow according to my certification manuals), and it still did it, was intermittent and once I rebooted, it went back to normal. First issues I've had with the inspire. I've now rolled back the firmware. My inspire is an Inspire 1 RAW as well.

I'm really after the revised firmware now as in back on 1.8. The bug is definitely there, however is intermittent so maybe hard to replicate

========== 2014.01.01 00:00:06 remo-con disconnect======
Packet: WM610_FC550_FW_V01.09.01.21.bin
Upgrading ...
Result: Success.

After receiving a "internal" revised FW 1.9.01.21 from DJI I have today done the new update with success. It is very windy here ( Sweden ) today - just able to do a short test - seems that DJI have fixed my and others problems with FW 1.9.....

nilsblix@gmail. Posted at 2016-7-2 22:49
========== 2014.01.01 00:00:06 remo-con disconnect======
Packet: WM610_FC550_FW_V01.09.01.21.bin
Upg ...

Hi Nilsblix,

I am glad to know you get positive result too.

Henry

Fingers crossed.

nilsblix@gmail. Posted at 2016-7-2 15:49
========== 2014.01.01 00:00:06 remo-con disconnect======
Packet: WM610_FC550_FW_V01.09.01.21.bin
Upg ...

Glad to know that.

Cheers Tony

nilsblix@gmail. Posted at 2016-7-2 08:49
========== 2014.01.01 00:00:06 remo-con disconnect======
Packet: WM610_FC550_FW_V01.09.01.21.bin
Upg ...

I don't even understand how you were able to get the "internal" firmware.  I've requested it and none of the reps know of its existence.  Did you get it from a rep here?  Was it some random email?  

Henry Mo-Yung Posted at 2016-7-1 21:50
Hi Rich,

The FW upgrade processing from FW v1.09.01.10 to the DJI's supplied "internal firmware"  ...

Henry

My gear were up and locked. I was filming a fir tree being cut down So I had the Inspire parked while the tree was being removed piece by piece. It was very obvious when I was about10 feet from the ground. I needed to hold up on the stick to keep my position. Never had this happen before... I feel if I had not given more up stick the Inspire would sink to the ground.

I was not having any trouble at the river two weeks ago and have a slow-mo showing my Inspire locked in a hover over the water with VPS turned on.




Rich

GabeZ Posted at 2016-7-3 00:53
I don't even understand how you were able to get the "internal" firmware.  I've requested it and n ...

I got the file from DJI after sales customer support. I think they have sent it to us that have provided DJI with our internal .dat files which can tell them whats wrong with our FW.

Henry Mo-Yung Posted at 2016-6-20 13:06
Oh No!

Did you say it came down by itself with the landing gear lifted and crashed on the X5R ca ...

Had the same happen to me this morning. What is going on????

So After the 1.9 firmware upgrade, all was ok, had a warning about sensor, and it rose once, but landed ok. I changed battery, it shot the job ok.

Until this morning. Weather has been shocking. Great day today, so got up early, check the craft software etc. Checked the IMU and did a stick calibration.
At site, usual preflight procedures, performed Compass calibration, checked & formatted sd card etc. Started motors, set home point, finished camera checks, then took of manually to about 2m. let go of sticks, and it still drifted up, landing gear stayed in down position. Touched the down stick to stop the drift, and the craft started to descend, let go of stick, and it still drifted down slowly. It then shot up, by its self, fast. I pulled the down stick to stop the ascent. In then went down fast. I steadied it at about 1.5 to 2 m, and set about landing. All though this the landing gear it down, and i have issued no command to raise it.
About 0.5m from landing, the landing gear then raised by itself, then landed on the X5 camera, even though I had stopped pulling the stick.
I killed the motors, and went to take a picture (attached)
As I started to take the picture, the land gear then started to lower, again by itself, with no command from the transmitter.
What is going on? Have commercial jobs this week, and cant trust the Inspire 1 Pro in this state.
I have tried to down grade the firmware to V1.8, as people have suggested, but now the craft will not accept any firmware files, and leaves no text reports when you try.
Im stuck, can anyone help?
I attached footage from the inspire, The flight record from app & picturehttps://www.dropbox.com/sh/ya5ez ... hnxzlWMXKrZR4a?dl=0

db050800 Posted at 2016-7-2 14:19
So After the 1.9 firmware upgrade, all was ok, had a warning about sensor, and it rose once, but lan ...

Hi db050800,
   What happens when you downgrade (or attempt to) and how are you doing it?  Normally, all you have to do is put the .BIN on your SD card and let it install.  If there's more on your SD card, make sure you remove everything but the .BIN file.  

GabeZ Posted at 2016-7-3 02:53
I don't even understand how you were able to get the "internal" firmware.  I've requested it and n ...

Add me and I can send you the link of the internal firmware

RichJ53 Posted at 2016-7-3 01:30
Henry

My gear were up and locked. I was filming a fir tree being cut down So I had the Inspire pa ...

Hi Rich,

It was strange. Those you experienced on today were similar to the issues I encountered but mine was still with FW v1.09.01.10 but yours was already back to FW v1.08.01.00 5 days ago.

I hope DJI can officially release the fixing firmware as soon as possible. In the mean time, be careful and good luck.

Henry

db050800 Posted at 2016-7-3 04:19
So After the 1.9 firmware upgrade, all was ok, had a warning about sensor, and it rose once, but lan ...

Dear Db050800,

Thanks for the thick grass, you were very lucky not resulting with a damaged I1 Pro!

Did you manage to have the corresponding bin file when you tried to downgrade? It should be the WM610_FC550_FW_V1.08.01.00.bin file, not the WM610_FW_V1.08.01.00.bin file.

Henry

Henry Mo-Yung Posted at 2016-7-3 08:00
Dear Db050800,

Thanks for the thick grass, you were very lucky not resulting with a damaged I1 P ...

Hi Db050800,

Please note that Rich experienced the issues on today even though he downgraded the FW to v1.08.01.00.

Be prepared not to panic if you encounter the issues after successfully downgrade your I1 Pro to FW v1.08.01.00.

Good luck!

Henry

SkyHigh UAV Posted at 2016-7-2 17:39
Add me and I can send you the link of the internal firmware

I tried to add you but got a "please wait" and request sent over your avatar.  I'm not sure if you got the request as it kept saying "please wait."  Alternatively, if I can't get that to work, do your have a company email I can reach you at?

Henry Mo-Yung Posted at 2016-7-2 16:41
Hi Rich,

It was strange. Those you experienced on today were similar to the issues I encountered  ...

Hi Henry,

So now I upgraded back to 1.9.10 FW and recal'd everything again. Just flew a 12min flight and everything tested out fine. Tomorrow we are flying again (not sure where yet)  I looked at the text file shown below and I see the (17) is one of the files you said DJI changed.... Can you send me a link to the internal FW file... I think I would like to try it for the Inspire 1 V2 X3 version. DJI PM is not working right now. I am puzzled on what to do at this point....  I am worried that something is buggy but I do not know what the cause is. I will send the dat file to DJI if they would like it....  DJI ?? let me know.

hidden log RED is the downgrade to 1.8 and blue is the upgrade 1.9

00009674]========== remo-con disconnect. boot(15) ============
[00009718]Packet [C:\WM610_FW_V01.08.01.00.bin] detected, card sn [0xb0407e22].
[00009770]Packet upgrade start...

[00009822]Packet checking...
[00009866]Packet vlink 01.08.0100 <-> 01.07.0090.
[00009912]Record vlink 01.09.0110 <-> 01.08.0100 (flow = 1).
[00009960]Done.

[00010007]Version checking[1]...
[00010053][01 00][00] v2.65.5033 -> v2.65.5033
[00010099][01 01][00] v2.65.5033 -> v2.65.5033
[00010181][03 05][00] v34.1.0.5 -> v34.1.0.5
[00010341][03 06][00] v2.4.20.18 -> v2.4.10.7 need upgrade.
[00010410][04 00][00] v1.29.0.92 -> v1.29.0.92
[00010501][05 00][00] v3.0.6.2 -> v3.0.6.2
[00010555][08 00][00] v2.14.9.42 -> v2.14.9.42
[00010621][09 00][00] v3.0.0.4 -> v3.0.0.4
[00010721][11 00][00] v3.9.0.0 -> v3.9.0.0
[00010821][12 00][00] v1.11.0.0 -> v1.11.0.0
[00010923][12 01][00] v1.11.0.0 -> v1.11.0.0
[00011021][12 02][00] v1.11.0.0 -> v1.11.0.0
[00011121][12 03][00] v1.11.0.0 -> v1.11.0.0
[00011259][15 00][00] v1.1.2.0 -> v1.1.2.0
[00011321][17 00][00] v1.1.0.6 -> v1.1.0.4 need upgrade.
[00011461][17 01][00] v2.0.1.6 -> v2.0.1.4 need upgrade.
[00011520][19 00][00] v1.0.8.96 -> v1.0.8.96
[00011569]Done.

[00013626]Waiting for user confirm...
[00023672]Timeout, start upgrade automatically.

[00023762]Firmware upgrading[1]...
[00023883][03 06] Firmware upgrade start...
[00243155][03 06] Firmware upgrade finished successfully.
[00243211][17 00] Firmware upgrade start...
[00285132][17 00] Firmware upgrade finished successfully.
[00285183][17 01] Firmware upgrade start...
[00318869][17 01] Firmware upgrade finished successfully.
[00318913]Done.

[00318962]Version checking[2]...
[00319008][01 00][00] v2.65.5033 -> v2.65.5033
[00319056][01 01][00] v2.65.5033 -> v2.65.5033
[00319132][03 05][00] v34.1.0.5 -> v34.1.0.5
[00319216][03 06][05] v2.4.10.7 -> v2.4.10.7
[00319274][04 00][00] v1.29.0.92 -> v1.29.0.92
[00319353][05 00][00] v3.0.6.2 -> v3.0.6.2
[00319406][08 00][00] v2.14.9.42 -> v2.14.9.42
[00319461][09 00][00] v3.0.0.4 -> v3.0.0.4
[00319551][11 00][00] v3.9.0.0 -> v3.9.0.0
[00319653][12 00][00] v1.11.0.0 -> v1.11.0.0
[00319751][12 01][00] v1.11.0.0 -> v1.11.0.0
[00319852][12 02][00] v1.11.0.0 -> v1.11.0.0
[00319951][12 03][00] v1.11.0.0 -> v1.11.0.0
[00321067][15 00][00] v1.1.2.0 -> v1.1.2.0
[00321132][17 00][05] v1.1.0.4 -> v1.1.0.4
[00321252][17 01][05] v2.0.1.4 -> v2.0.1.4
[00321308][19 00][00] v1.0.8.96 -> v1.0.8.96
[00321364]Packet upgrade finish successfully.



[00010017]========== remo-con disconnect. boot(15) ============
[00010067]Packet [C:\WM610_FW_V01.09.01.10.bin] detected, card sn [0xb0407e22].
[00010116]Packet upgrade start...

[00010182]Packet checking...
[00010228]Packet vlink 01.09.0110 <-> 01.08.0100.
[00010283]Record vlink 01.09.0110 <-> 01.08.0100 (flow = 0).
[00010351]Done.

[00010407]Version checking[1]...
[00010465][08 00][00] v2.14.9.42 -> v2.14.9.42
[00010524][01 00][00] v2.65.5033 -> v2.65.5033
[00010610][01 01][00] v2.65.5033 -> v2.65.5033
[00010716][03 05][00] v34.1.0.5 -> v34.1.0.5
[00010816][03 06][00] v2.4.10.7 -> v2.4.20.18 need upgrade.
[00010884][04 00][00] v1.29.0.92 -> v1.29.0.92
[00010956][05 00][00] v3.0.6.2 -> v3.0.6.2
[00011021][09 00][00] v3.0.0.4 -> v3.0.0.4
[00011116][11 00][00] v3.9.0.0 -> v3.9.0.0
[00011216][12 00][00] v1.11.0.0 -> v1.11.0.0
[00011316][12 01][00] v1.11.0.0 -> v1.11.0.0
[00011416][12 02][00] v1.11.0.0 -> v1.11.0.0
[00011516][12 03][00] v1.11.0.0 -> v1.11.0.0
[00011653][15 00][00] v1.1.2.0 -> v1.1.2.0
[00011736][17 00][00] v1.1.0.4 -> v1.1.0.6 need upgrade.
[00011876][17 01][00] v2.0.1.4 -> v2.0.1.6 need upgrade.
[00011940][19 00][00] v1.0.8.96 -> v1.0.8.96
[00011990]Done.

[00014053]Waiting for user confirm...
[00024101]Timeout, start upgrade automatically.

[00024193]Firmware upgrading[1]...
[00024322][03 06] Firmware upgrade start...
[00259710][03 06] Firmware upgrade finished successfully.
[00259769][17 00] Firmware upgrade start...
[00300927][17 00] Firmware upgrade finished successfully.
[00300984][17 01] Firmware upgrade start...
[00334663][17 01] Firmware upgrade finished successfully.
[00334708]Done.

[00334782]Version checking[2]...
[00334837][08 00][00] v2.14.9.42 -> v2.14.9.42
[00334883][01 00][00] v2.65.5033 -> v2.65.5033
[00334930][01 01][00] v2.65.5033 -> v2.65.5033
[00335027][03 05][00] v34.1.0.5 -> v34.1.0.5
[00335127][03 06][05] v2.4.20.18 -> v2.4.20.18
[00335190][04 00][00] v1.29.0.92 -> v1.29.0.92
[00335346][05 00][00] v3.0.6.2 -> v3.0.6.2
[00335406][09 00][00] v3.0.0.4 -> v3.0.0.4
[00335487][11 00][00] v3.9.0.0 -> v3.9.0.0
[00335574][12 00][00] v1.11.0.0 -> v1.11.0.0
[00335666][12 01][00] v1.11.0.0 -> v1.11.0.0
[00335748][12 02][00] v1.11.0.0 -> v1.11.0.0
[00335847][12 03][00] v1.11.0.0 -> v1.11.0.0
[00337460][15 00][00] v1.1.2.0 -> v1.1.2.0
[00337526][17 00][05] v1.1.0.6 -> v1.1.0.6
[00337647][17 01][05] v2.0.1.6 -> v2.0.1.6
[00337712][19 00][00] v1.0.8.96 -> v1.0.8.96
[00337762]Packet upgrade finish successfully.

Rich

RichJ53 Posted at 2016-7-3 08:54
Hi Henry,

So now I upgraded back to 1.9.10 FW and recal'd everything again. Just flew a 12min fli ...

Hi Rich,

I added friend with you. Do you need to confirm it so that we can send PM to each other? It seems I can't send PM to you.

Henry

Henry Mo-Yung Posted at 2016-7-2 20:54
Hi Rich,

I added friend with you. Do you need to confirm it so that we can send PM to each other? ...

Henry

Yes, I see you did......  The PM is currently not working .. Ken has reported it to the web guys.  

we are like 15 hours apart so if you fly again today please post how everything is working. I will check it before I fly tomorrow.

Rich

GabeZ Posted at 2016-7-3 00:22
Hi db050800,
   What happens when you downgrade (or attempt to) and how are you doing it?  Normall ...

Thanks GabeZ, have been trying to do that all night. It just sit there with a green light on the camera, and does not go in-to the firmware mode.; Tried different sd cards, formating them in the inspire etc.

Hi Rich,

I set off my I1 Pro twice in this morning and it performed consistently as it used to be.

Good luck!

Henry

Henry Mo-Yung Posted at 2016-7-3 01:00
Dear Db050800,

Thanks for the thick grass, you were very lucky not resulting with a damaged I1 P ...

Thank you Henry,
Yes, seems to be the correct BIN.
It will not go into firmware mode at all. Shame theres not a reset switch....or is there??

Henry Mo-Yung Posted at 2016-7-2 22:52
Hi Rich,

I set off my I1 Pro twice in this morning and it performed consistently as it used to be.  ...

That's awesome news Henry..    To bad we cant get this new FW link!

Rich

RichJ53 Posted at 2016-7-3 08:00
That's awesome news Henry..    To bad we cant get this new FW link!

Rich

Yes, hope we can get the new FW link. My Inspire is grounded because of this and I want to fly now on the holiday. Glad though that the internal firmware seems to fix the issues!