Started upgrading my firmware yesterday according to the instruction. Everything went fine until it stuck at 53 %. Finally I turned it off. Now I can't ugrade it again. The app still show the old firmware version. What do I need to do to  restart the procedure?David

Delete the log file from the microSD card, put it back into the Inspire camera.

Try this sequence:
1. Power on remote
2. Power on quad
3. Exit travel mode
4. Power down quad
5. Attach camera/gimbal
6. Power up the quad
7. Wait for app to ask if you want to install firmware; proceed

Let me know if that works for you

Thanks, will try it right now

I did exactly what you said. Nothing new  is happening.  The app says SAFE TO FLY,  nothing in the overall status, firmware version is 01.15, App version 1.0.2, RC 0.1.03

It says SAFE TO FLY and no firmware warning? That's interesting.

Try downloading the 0.16 firmware from DJI again, extract and copy the BIN file into a freshly formatted microSD. I once downloaded the file into the same Download folder, extracted it, and copied an older BIN into the microSD

ghoonk Posted at 2015-1-18 02:45
It says SAFE TO FLY and no firmware warning? That's interesting.

Try downloading the 0.16 firmware ...

I did that at least 5-6 times

I have the same issue, except now my remote can't connect to the aircraft, and I can't put it back in travel mode, or do anything with it at all.

The way I did mine I I took the sd card out of the camara and powered up the bird after It did setup sequence I put the SD card back into the camara. And that's how it took mine.

uomemoney Posted at 2015-1-18 09:02
I have the same issue, except now my remote can't connect to the aircraft, and I can't put it back i ...

Okay - suggest both of you contact the 24-hour Inspire tech support ASAP. Use the live chat, drop them a message and let us know what they say. This is rather odd.

good video to watch

david_quy Posted at 2015-1-18 02:31
I did exactly what you said. Nothing new  is happening.  The app says SAFE TO FLY,  nothing in the o ...

APP says SAFE TO FLY, that means u are already in latest firmware... Never doubt.

david_quy Posted at 2015-1-18 02:31
I did exactly what you said. Nothing new  is happening.  The app says SAFE TO FLY,  nothing in the o ...

TX took the install of firmare quickly like 2 mins looked good.

I have the same issue as you  pilot app status screen blank.
firmware update app version 1.0.2.RC.1.03 as well here

All went smooth when the firmware hit the drone  it ran thru a series of beeps and flashing lights then it locked up 15 mins into the install flashing red and beeping for 45 mins I too powered it down battery was about dead as well..ughh..........................................Pilot app said no SD and gave no status during the firmware install.


Says ready to fly .Motors come on it throttles up in no GPS mode(good yellow flashing light) I did notice the throttle speed increasing all on its own when I hit the throttle a few times without props .
Video feed was there and no request to update firmware as well.

Im stumped and tired...Funny thing is it looks like everything is operable.

Any ideas ..ty.
Would it help to pop out the SD reformat it dump the bin file on the SD insert the sd with new firm
ware again and power it up??

The Colonel Posted at 2015-1-18 17:46
TX took the install of firmare quickly like 2 mins looked good.

I have the same issue as you  pilo ...

APP handles the firmware version verification. If it doesn't say firmware update needed, u can just keep focus on ur flight.

ghoonk Posted at 2015-1-18 13:31
Okay - suggest both of you contact the 24-hour Inspire tech support ASAP. Use the live chat, drop  ...

I have contacted the online chat, phone support, and email support, and as of now, no one has figured out how to link the Inspire1 back to the remote. Today is day #3 with this issue, hopefully it will get resolved very soon.

The Colonel Posted at 2015-1-18 13:49
good video to watch
https://www.youtube.com/watch?v=6WKz7pO0zlE

I watched that video (good vid btw), and that was the procedure I used to update the firmware, but now my remote is disconnected from the Inspire1.

so sorry to hear that.

TXT file from firmware update
stated


result: success

This video talks about firmware update time out issues.  Doesn't talk about binding the remote back to the Inspire, but it might help when first encountering this problem.

airymok Posted at 2015-1-18 19:03
APP handles the firmware version verification. If it doesn't say firmware update needed, u can jus ...

Interesting as the TXT file also says result Success.

Im gonna see if I I get a good gps signal and move to an area to do so..

It looks like its fully operational....????
Still shows original firmware version though??
I will report back later today hope to see people get this resolves ..Never lost the TX connect that's really weird.


UPDATE resolved and new firmware confirmed