I went to check the manual in the academy section of the app and it download a new version 2015-3.  The first pages show how to install the 1345s props.  Looks like further confirmation that new inspires will have new props and hopefully previous owners will get the the rumored free upgrade.

All sounds positive.

Just went to the Academy on the iOS App and still shows v1.0 for the User Manual ??

GB44 Posted at 2015-3-26 04:08
Just went to the Academy on the iOS App and still shows v1.0 for the User Manual ??

It still says version 1 but the date has changed to 2015-3 on the cover.

HeadOn Posted at 2015-3-26 05:11
It still says version 1 but the date has changed to 2015-3 on the cover.

Yes, I see it now.

And they do have the new props in there with the clips on the engine mounts, so I guess they must be going to run with these now.

Thanks for highlighting this, appreciated.

Thank you for the advice

free sets would be nice ... I did find them at a dealer and ordered 4 sets of two props with the yeller stripes , and three sets of two quick release mounts .. Not doing the maybe deal and waiting forever again if they decide not to hand them out free...just like the phantoms and the new props they made but never gave out for free.... It was  Just another upgrade as time passed .

Here is the link to buy them. I have ordered mine for experiment with until the free ones are provided by DJI (if they do)

http://store.dji.com/tuned-propulsion-system/e800

so am I right in saying we just need to order the props and they will fit the inspire motors?

Yes David, It is written in the description. Fits both E800 and Inspire.

Just do not forget to add the quick release adaptors of course...

The new props will be shipped to all registered users.

How and when Ed???

I've registered my I1 over the Pilot app , so do I become a mail from DJI for my adress???

+1 this is a good notice after all headache of the new firmware...

Tahoe_Ed Posted at 2015-3-26 14:49
The new props will be shipped to all registered users.

Ed,

This is a very Positive decision from DJI, to issue the new props.

Just for clarity, does that include the hold down clips you screw into the engine mount ?

I checked with my dealer and they said DJI will be shipping six 1345s props and four prop installation kits.  Should be shipping out free from dealers sometime around mid-April.

GB44 Posted at 2015-3-26 23:56
Ed,

This is a very Positive decision from DJI, to issue the new props.

Yes it will.  This is the set up I have been testing for about a month.  

Tahoe_Ed Posted at 2015-3-27 02:11
Yes it will.  This is the set up I have been testing for about a month.

Ed,

That is a really good decision for DJI.  The system looks real easy.

So do the mounts just screw into the engine mounts or does DJI recommend using some locktite on the threads.

I so the E800 blade and lock clips  will fit the inspier one ?  ok like there are 2 screw holes on each motor for the E800 locking clips ?

HeadOn Posted at 2015-3-27 01:52
I checked with my dealer and they said DJI will be shipping six 1345s props and four prop installati ...

Yea, I got the same confirmation from DJI today as well. They said mid-end April we should be seeing them here in the US...

GB44 Posted at 2015-3-27 02:16
Ed,

That is a really good decision for DJI.  The system looks real easy.

I would use a little blue loctite and I mean a little.  I like the gel and use a toothpick.  That is all you will need.  

Tahoe_Ed Posted at 2015-3-27 04:32
I would use a little blue loctite and I mean a little.  I like the gel and use a toothpick.  That  ...

Ed,

Do you have the Locktite model number as there are lots of different ones.

GB44 Posted at 2015-3-27 05:26
Ed,

Do you have the Locktite model number as there are lots of different ones.

Thread locker blue 242 will work fine and you will still be able to undo it again.
DONT whatever you do use the red or retaining compound or you will break your screwdriver and probably your wrist trying to loosten it afterwards!!

markjacobs.talk Posted at 2015-3-27 06:55
Thread locker blue 242 will work fine and you will still be able to undo it again.
DONT whatever y ...

Cheers Mark, just need my replacement Inspire now and hopefully it will come with the new props....

markjacobs.talk Posted at 2015-3-27 06:55
Thread locker blue 242 will work fine and you will still be able to undo it again.
DONT whatever y ...

I've got some loctite 243. Any good?

Are we positive that 242 is ok as it's rated at medium strength

Exib Posted at 2015-4-15 00:54
Are we positive that 242 is ok as it's rated at medium strength

It's fine. I use it on my helis every day.
You just want the tiniest amount though on a couple of the threads applied with a toothpick.
Any more and it will wick down the threads.

markjacobs.talk Posted at 2015-4-15 14:59
It's fine. I use it on my helis every day.
You just want the tiniest amount though on a couple of  ...

Many thanks for the clarification

Tahoe_Ed Posted at 2015-3-26 14:49
The new props will be shipped to all registered users.

and new screws on inspaer 1 will give the dealer for free or buy? inspair one bought from a dealer in Russia they will be available to me for free?

GB44 Posted at 2015-3-27 02:16
Ed,

That is a really good decision for DJI.  The system looks real easy.

They come with blue Loctite on them already plus there are two extra screws in case you loose one in the packet.......

bolwerk.arnold Posted at 2015-3-26 16:42
How and when Ed???

I've registered my I1 over the Pilot app , so do I become a mail from DJI for my ...

I've registered via the app, too.
How can we obtain those free sets?
What do we have to to?

As it turns out I got my Inspire replaced under warranty and it came already fitted wit the new e800 props, ready to go.  No extra screws though.

Ed  or anyone recommend some glue that will stick to the foam inside the case.  The velcro pad for securing the straps for the props keep coming off.  Tried using super glue but still won't stick to the foam.  Not sure what other glue would be suitable.

I just received a shipment of quick release props from B&H... I received 5 sets... I think 2 of them were sets I ordered originally with the inspire and they sent the new ones instead... I assume the 3 extra sets are the free ones supposedly promised... Problem is they just sent the props... I have no way to attach them to the birds... am I missing something?

Just got off the phone with UAV direct where I purchased my second inspire... They said they received the props but they did not receive any connection kits.. they are holding off shipment until the whole package is complete.. Makes perfect sense to me... Hopefully B&H will not forget to send the rest when it comes in.

My Inspire 1 that came from B&H this week have them pre-installed. Inspection card says March 23. Very fresh stock,