Please select Into the mobile phone version | Continue to access the computer ver.
MC Connection to Center Board Failed when trying to upgrade 1.2.1.0
15436 22 2015-4-15
Uploading and Loding Picture ...(0/1)
o(^-^)o
sanvi61
lvl.2
Flight distance : 3455 ft
Spain
Offline

                                                                        
                                                                                Hi:
Have this error at power dji inspire to update the new firmware 1.2.1.0:
"MC connection to center board failed"
Solution: Please restart aircraft, if it still fails, please contact customer service.

Gimbal cannot receive MC data
Solution: try to plug the 8 pin line between damping plate and aircraft, check if the pins of 8 pin line is loose. If it still fails, please contact customer service.

And I can not find how to fix this error.
Anyone know how to fix this error?                                       
                                
                                                                                       
                                                                                                                                                                                                        
2015-4-15
Use props
klute
lvl.3
Flight distance : 45278055 ft
  • >>>
Norway
Offline

Did you power of your RC before you started the update?
2015-4-15
Use props
sanvi61
lvl.2
Flight distance : 3455 ft
Spain
Offline

klute@online.no Posted at 2015-4-16 02:40
Did you power of your RC before you started the update?

Yes I power the RC before started the update.
2015-4-15
Use props
klute
lvl.3
Flight distance : 45278055 ft
  • >>>
Norway
Offline

sanvi61 Posted at 2015-4-16 02:45
Yes I power the RC before started the update.

Powered off I hope. The RC must be power off before you power up your bird.
Had the same problem. Powered the Inspire off and powered up again. Lots of beeping 20 minutes and then all OK.
It´s an tutorial in Academy in the Pilot app.
2015-4-15
Use props
sanvi61
lvl.2
Flight distance : 3455 ft
Spain
Offline

klute@online.no Posted at 2015-4-16 02:58
Powered off I hope. The RC must be power off before you power up your bird.
Had the same problem.  ...

No I power ON the rc before you power up your bird. Then when i connect the drone show this error "MC connection to center board failed".
2015-4-15
Use props
klute
lvl.3
Flight distance : 45278055 ft
  • >>>
Norway
Offline

sanvi61 Posted at 2015-4-16 03:12
No I power ON the rc before you power up your bird. Then when i connect the drone show this error  ...

The RC must be powered off before you start up your Inspire and the update starts. Watch the tutorial video in the pilot app to get all details.
2015-4-15
Use props
vincenzor1
lvl.2

Canada
Offline

klute@online.no Posted at 2015-4-16 03:26
The RC must be powered off before you start up your Inspire and the update starts. Watch the tutor ...

Still no go I get the same error.
2015-4-15
Use props
sanvi61
lvl.2
Flight distance : 3455 ft
Spain
Offline

Many Thanks !!!.
Updated to new firmware OK.
The RC must be powered off.
resultado update 1.2.01.00 DJI Inspire.PNG
2015-4-15
Use props
klute
lvl.3
Flight distance : 45278055 ft
  • >>>
Norway
Offline

sanvi61 Posted at 2015-4-16 05:02
Many Thanks !!!.
Updated to new firmware OK.
The RC must be powered off.

Nice going
2015-4-16
Use props
klute
lvl.3
Flight distance : 45278055 ft
  • >>>
Norway
Offline

vincenzor1@gmai Posted at 2015-4-16 04:35
Still no go I get the same error.

Power off Inspire and try again. Sure you have the right file? WM610_FW_V01.02.01.00.bin
2015-4-16
Use props
Ozren
lvl.4

Croatia
Offline

I have the same error, cant fix it !! Does anyone have a fix?
2015-4-16
Use props
madh
lvl.2
Flight distance : 1978114 ft
Canada
Offline

I also have this error.  
2015-4-16
Use props
Ozren
lvl.4

Croatia
Offline

Fixed, just dont power the RC, delete the .TXT file and just leave .BIN file on the card. Turn on the Inspire and WAIT !! i waited for 25 mins and the error and loud beeping was gone.
2015-4-16
Use props
madh
lvl.2
Flight distance : 1978114 ft
Canada
Offline

Thanks Ozren. I was restarting the copter after it switched to the D-DDD D-DDD...  Only waiting for that didn't get out of motor lock. After reading your post, I restarted upgrade with copter only, then went for a walk. When I got back after nearly 20 minutes the loud motors locked sound was gone!  Finally!!!!  Thanks again.

2015-4-16
Use props
madh
lvl.2
Flight distance : 1978114 ft
Canada
Offline

Correction. Meant to type D---DD, like it says in upgrade doc. That comes far sooner than 25 minutes. Only when I left it for 20 minutes or so did the motors unlock.
2015-4-16
Use props
bramoostdijk
lvl.1
Flight distance : 842913 ft
  • >>>
Netherlands
Offline


Help!!!!

I have the new Firmware installed and now get all the time on start up Beep-Beep-Beep-Beep ... etc.. No taillight!

I don't remember if I had the RC stand or like.
Now I have the whole SD card erased and only the v1.3.0 in the Bin.

Nothing helps ...;(
2015-8-9
Use props
elgeish
New

United States
Offline

Ran into the same issue with the Phantom 3 Pro and FW v1.3.20, the loud alarming beeping stopped after 10 minutes and the new FW installed correctly. Lesson learned, turn off the RC first!
2015-8-9
Use props
bramoostdijk
lvl.1
Flight distance : 842913 ft
  • >>>
Netherlands
Offline

I do.... everything is of the SD card (clean) only the FW V1.3.0... RC is off... no leds...
Can i re-install the lastes FW?
I installes now the  v1.2.1.06, (in progress) than i reinstall the version V1.3.0 (without RC off) .... hopes it works #fail
2015-8-9
Use props
jorge.tam
lvl.2
Flight distance : 1699003 ft
Portugal
Offline

Hi, how did you solved the issue?
2015-9-8
Use props
access53
lvl.1

Aruba
Offline

bramoostdijk@ho Posted at 2015-8-9 05:20
I do.... everything is of the SD card (clean) only the FW V1.3.0... RC is off... no leds...
Can i r ...

Hi friend, I have the same problem, did you fix it? Thanks for your time
2015-11-16
Use props
Mrgreygoose
lvl.2
United States
Offline

easy fix don't turn on the remotes. Delete all files on the SD card and then only have the BIN file. Make sure battery is fully charged and then insert SD card and turn on the Drone only!!
Its going to do the loud beep and you might see it twitch. But about 25 mins into it there will be a multi beep and the upgrade has gone through.

Here's a link to my issue when I got the error message I included a photo so you can see if the error looks like yours..

http://forum.dji.com/forum.php?m ... D216%26typeid%3D216
2015-11-17
Use props
fans9e35b2f1
New
United States
Offline

remember if you use your DJI equipment for work it will most likely run into an issue like this where you will lose money and possibly clients. my Osmo stopped recording audio right before having to record a band. went out and dropped another $700 on a new Osmo so I could record the band. now I have a production with the inspire and this crap happens. I'm getting really sick of my equipment always having issues. not good for my reputation and it certainly won't be for DJI either.

im not one to complain but when you have over 10k invested into DJI products and it never works when you need it gets pretty frustrating.
2017-8-7
Use props
Donnie *
Captain
Flight distance : 3636782 ft
United States
Offline

The fix for this warning is to do a Full  IMU  calibration and follow that immediatly with a compass calibration .  I have seen this several times before .

donnie
2017-8-8
Use props
Advanced
You need to log in before you can reply Login | Register now

Credit Rules