I just my new O3 Airunit and have updated the firmware and activated it but I can't bind it with my goggles.
When I plug the air unit in over USB it only shows a solid green light even when I press the bind button. There is no red light, no blinking red light like i've seen on the online videos, even if i hold the bind button nothing happens?
To confirm I'm on the latest firmware V01.01.0000 and I dont have the airunit wired into the drone I'm powering it on through the USB,
If anyone can help that'd be amazing! I'm worried that I've got a faulty unit? I can't fine any troublshooting about what the led indicators are meant to mean online.
Thanks

Hi,

You might be better off posting in the products section of this forum. That is way more active!
https://forum.dji.com/forum-129-1.html

Hello, there. Sorry for your inconvenience. To better help you, would you mind recording a video for us? Please record the binding process. We will consult your issue with our engineers. Thanks a lot.

I have the exact same problem, just got my 03 unit

I also have the exact same problem. All firmware is up to date in the O3 Air unit, the Goggles 2 and the Remote Controller 2. The O3 Air Unit is not binding to anything, I have it powered form the USB port. No red light when I depress the bind button on the Air Unit. Light stays green and nothing happens, except for lots of beeping from the controller and the goggles.

I also have the exact same problem. All firmware is up to date. I resolve my problem.
1) is not possible bind air unit powered with usb-c
2) My FC is a  T-Motor Mini F7 20x20 Flight Controller HD . The connector for the FC supply 10 Volt at the air unit but the current is not bigger for supply o3Air Unit . I removed the power wire and I have connected directly to the battery.
Now is possible bind the the air unit and is work perfectly with my Googles 2

i have same issue

I have the same issue. I purchased a BNF drone from iFlight, everything is check, O3 activated and updated to latest FW version. Plugged in lipo battery but O3 cannot go into binding mode. No red light when I press the binding button. Any solution for this?

Problem solved. The O3 unit wasn’t on. There should be a green led right that turns red, I had to connect to Betaflight and go to modes, scroll down to the bottom and find the User 1 & user2 and add a range.

Please let me know if you need any other help!

justmedi Posted at 2-5 08:40
Problem solved. The O3 unit wasn’t on. There should be a green led right that turns red, I had to connect to Betaflight and go to modes, scroll down to the bottom and find the User 1 & user2 and add a range.

Oh good, it's working for me, thank you !! I've never heard of them

justmedi Posted at 2-5 08:40
Problem solved. The O3 unit wasn’t on. There should be a green led right that turns red, I had to connect to Betaflight and go to modes, scroll down to the bottom and find the User 1 & user2 and add a range.

This solved the problem for me!!! Thank you so much for posting

justmedi Posted at 2-5 08:40
Problem solved. The O3 unit wasn’t on. There should be a green led right that turns red, I had to connect to Betaflight and go to modes, scroll down to the bottom and find the User 1 & user2 and add a range.

I can't seem to find that in the new betaflight 10.9. Do you mean camera control 1 and 2?

well ive been try ing to build a drone ..ive have a ARGUS F7 eco pro.  and a DJI o3  .. and a dji motion 2 ..and a fishy lite controller --- I'm just stuck hear can't get nothing on the web????????  

03 air unit binding button is broken, is there any way to bind to controller 2 and goggles2 without binding button on the 03?

justmedi Posted at 2023-2-5 08:40
Problem solved. The O3 unit wasn’t on. There should be a green led right that turns red, I had to connect to Betaflight and go to modes, scroll down to the bottom and find the User 1 & user2 and add a range.

Did you have to add both user 1 and user 2 ? Or just one or the other ? Thanks.

Problème résolu. L'unité O3 n'était pas allumée
. Il devrait y avoir une LED verte à droite qui devient rouge, j'ai dû me connecter à Betaflight et aller dans les modes, faire défiler vers le bas et trouver l'utilisateur 1 et l'utilisateur 2 et ajouter une plage.

salut je serais intéressé de savoir comment faire sut btfl 10.10.0 merci

le_hugggg13 Posted at 8-9 06:37
salut je serais intéressé de savoir comment faire sut btfl 10.10.0 merci

Hi there,
thank you for reaching out.

Kindly inform us the full details of the issue that you experienced with your DJI product, and we will surely provide you with an accurate resolution after we review the details. Rest assured that we're committed to providing the best experience for our users.

Please keep us posted. Thank you for understanding.