Please select Into the mobile phone version | Continue to access the computer ver.
P3P No Signal - No Camera Video on App
2011 38 2015-12-24
Uploading and Loding Picture ...(0/1)
o(^-^)o
john.gual
lvl.1

United States
Offline

This is a new unit.  I tried to install the latest firmware but keep getting an error (solid red indicator light, loud constant noise after about 1 minute).  I also have a red "No Signal" warning at the top center of the screen.  Further, the center window is blank; the app is not displaying a live video feed.  In spite of that my app is reading all data from the aircraft, and will control the aircraft motors and gimbal.  If I snap a picture, then put the SD card in my computer I get good clean JPEGS.  I am guessing sometinh went wrong in the firware update, but I can not figure out how to either reverse the update and try again, or to get it to simply reinstll the update.  The txt log file says failure, try the update again.  Any ideas?
2015-12-24
Use props
cacollins0220
lvl.3
Flight distance : 294016 ft
United States
Offline

Had the same problem with mine. I had to reboot my tablet. then everything worked fine.
2015-12-24
Use props
DJI-Patrick
Captain

Hong Kong
Offline

Hi , please try relink the RC to the aircraft .  If that doesn't work , please try reset the RC by this way :  press the C1 + C2 + Photo  buttons, keep them pressed and TURN OFF the controller.Then ,keep the C1 + C2 + Trigger (photo) buttons pressed  and turn the controller on . Thank you !
2015-12-24
Use props
john.gual
lvl.1

United States
Offline

DJI-Patrick Posted at 2015-12-25 02:33
Hi , please try relink the RC to the aircraft .  If that doesn't work , please try reset the RC by t ...

Thank you.  I tried both but neither helped.  Just to be clear, it appears everything on the RC works except the video feed.  Also, I was never able to get a clean firmware upgrade - I keep getting failure.  At this point, when I tried to do the upgrade again, after about 30 seconds I get a solid red indicator light and a solid audio tone.  I keep thinking it is a software issue.  Is there a way to force an upgrade of the firmware on the aircraft?
2015-12-25
Use props
rapidmachine
lvl.1

United States
Offline

John, I am having the same exact issue. I have tried to downgrade the software back to 1.4 but it will not take. Any level of upgrade (1.5 or 1.6) seems to do the constant solid beep after several minutes. The drone flies fine and even records videos/pictures but I cannot see any feed on my tablet. It also shows the red bar at the top saying "No Signal". I have been pulling my hair out looking to correct this issue. It seems it started when I updated my RC firmware/software. I am hoping someone has a solution soon.
2015-12-25
Use props
georgiacdj
New

United States
Offline

Exact same issue. No video feed to my tablet or phone. I can take video and pictures and then download them from the aircraft to my PC. Tried all the above steps in to no avail. Aircraft, RC and tablet all show the latest versions. Super frustrating.  Any other suggestions?
2015-12-26
Use props
Warrior
lvl.1

United States
Offline

georgiacdj Posted at 2015-12-26 19:01
Exact same issue. No video feed to my tablet or phone. I can take video and pictures and then downlo ...

I am having the exact same problem - no "Enter Camera View" on app.   I have not flown in several months - last time back in Sept.  Before that I  had competed over 40 flights.  Now the the RC will not connect to my iPad Air 2.  Also tried with my iPhone 5s and still no connection - no camera view button.  The RC will control the bird but no data (telemetry or camera feed) on DJI Go app.  I have updated the aircraft to Firmware V1.6.0040.  When trying to update RC with microChip via USB nothing happens leading me to believe the USB port on RC is not functioning.  I have the latest version of the DJI Go app (2.4.3)   Recommendations?  Does the Firmware V1.6.0040 contain an update for the RC?
2015-12-26
Use props
3dimodels
lvl.1
Flight distance : 1787057 ft
  • >>>
United States
Offline

I get an error once i start flying. I have video feed and can shoot whilst on the ground. As soon as i start flying,  i can't control the camera or see anything the camera sees.  I need to restart the P3 and my rc/phone a couple of times. Sometimes the gimbal flops and points down.  Only 4 flights and this has happened from the begining. I updated the firmware as soon as I bought it. Very frustrating.
2015-12-27
Use props
DJI-Ken
DJI team
Flight distance : 1515312 ft
  • >>>
United States
Offline

First off, is everyone using devices on the DJI list?
If so, try deleting the app, rebooting your device, then re-install the app. Then try to relink the aircraft. Are you getting all telemetry data and just so video picture?
2015-12-27
Use props
john.a.laporte
lvl.1

United States
Offline

I am having the same issue.  I just bought the Phantom 3 Pro a couple weeks ago and took it out of the box yesterday.  I charged everything up and turned it on and everything linked up fine, the controller, etc...except for a live feed from the camera.  I read some other forums and thought maybe the issue would be cleared up with the firmware upgrade.  I tried to upgrade the Phantom and it seemed to work ok as it ran the upgrade for about 20 minutes, but then all I got was a loud continuos siren with yellow flashing lights.  I checked the SD card and it said upgrade failed and try again.  I tried it again and it seems to start the upgrade but goes back to the loud continuous siren with flashing yellow lights.  The light on the gimbal front shows solid red.  I have tried several times but get the same results.  When I reconnect with the DJI app it says my firmware is the latest though, even though I have never had a text file stating the upgrade was successful.  I am also still having the issue with the no signal from the camera.  I can take pictures and video but the live image does not show up.  I tried using a Samsung Galaxy S5 and my Tab 4.  Both run the app fine, but no picture from camera.  Any ideas or help is appreciated.  I am thinking I need to return the unit and get a new one, but hope there is something I am missing.

Thanks.
2015-12-28
Use props
Triyandis
New

Indonesia
Offline


I had a problem same in my p3pro,1. When I used firmware 1.4 and DJI GO app before 2.4.3, all operated is done. But when I updated DJI GO app to 2.4.3, live HD in my device (IOS mini ipad) is blank but all button is function (look picture!). Then drone flied fine and even records videos/pictures but I cannot see any feed on my device and only see in my computer with microsd.this is problem to make me very frustated because I will used in my work. I had tried remove app, reboot my device, reinstall app, and result is same. Also, I tried in Android and result is same. Also I tried press the C1 + C2 + Photo  buttons, keep them pressed and TURN OFF the controller.Then ,keep the C1 + C2 + Trigger (photo) buttons pressed  and turn the controller on, and result is same. Any ideas or solution for this problem ?? Please DJI tech support gave solution for this problem.

2. When I tried firmware update to 1.6.0040 as always failed result with sound in gimbal D...... then I had tried reboot aircraft and tried again. result is same. Any solution ?
2015-12-28
Use props
john.gual
lvl.1

United States
Offline

DJI-Ken Posted at 2015-12-27 22:53
First off, is everyone using devices on the DJI list?
If so, try deleting the app, rebooting your de ...

Ken,

I am running a new iPad Air 2 with updated iOS which is on the DJI list.  I followed the above procedure, with no change.  I have full telemetry, full functionality.  I can take photos or shoot video that I can see when I download the files from the micro SD card.  The only issue I have is no live video feed, and the accompanying red "No Signal
" status.
2015-12-28
Use props
lperry17
New

United States
Offline

We purchased the Phantom 3 Advanced and it seems we are having the same issues.  We are unable to see the Camera Video view and also the upgrade to the firmware fails, no matter how many times we try, or re-format the SD card, or what order we turn on the RC and the Aircraft and the Galaxy S5 phone.  

I've copied below a couple of log files that came from the SD card, one if the file that shows the failure and the other is the hidden file.  Any assistance would be greatly appreciated.  Nothing worse than spending all that money and I can't see video or upgrade the firmware.  At first I thought my machine was bad, but now that I see a lot of issues in this forum, I'm not so sure.

P3S_FW_RESULT_AB
========== 2014.01.01 00:34:36 remo-con disconnect======
Packet: P3S_FW_V01.06.0040.bin
Upgrading ...
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.

========== 2014.01.01 00:00:22 remo-con disconnect======
Packet: P3S_FW_V01.06.0040.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.

========== 2014.01.01 00:00:22 remo-con disconnect======
Packet: P3S_FW_V01.06.0040.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.

========== 2014.01.01 00:00:22 remo-con disconnect======
Packet: P3S_FW_V01.06.0040.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.

========== 2014.01.01 00:04:16 remo-con disconnect======
Packet: P3S_FW_V01.06.0040.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.

========== 2014.01.01 00:00:22 remo-con disconnect======
Packet: P3S_FW_V01.06.0040.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.

========== 2014.01.01 00:00:21 remo-con disconnect======
Packet: P3S_FW_V01.06.0040.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.

========== 2014.01.01 00:00:22 remo-con disconnect======
Packet: P3S_FW_V01.06.0040.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.

========== 2014.01.01 00:00:22 remo-con disconnect======
Packet: P3S_FW_V01.06.0040.bin

========== 2014.01.01 00:00:22 remo-con disconnect======
Packet: P3S_FW_V01.06.0040.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.

========== 2014.01.01 00:00:22 remo-con disconnect======
Packet: P3S_FW_V01.06.0040.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.

========== 2014.01.01 00:02:18 remo-con disconnect======
Packet: P3S_FW_V01.06.0040.bin
Result: Corrupted.
Firmware bin file is corrupted, download it again from the DJI offical website.

========== 2014.01.01 00:00:22 remo-con disconnect======
Packet: P3S_FW_V01.05.0030.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.

========== 2014.01.01 00:00:22 remo-con disconnect======
Packet: P3S_FW_V01.05.0030.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.

========== 2014.01.01 00:00:22 remo-con disconnect======
Packet: P3S_FW_V01.05.0030.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.

========== 2014.01.01 00:00:22 remo-con disconnect======
Packet: P3S_FW_V01.06.0040.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.

========== 2014.01.01 00:00:22 remo-con disconnect======
Packet: P3S_FW_V01.06.0040.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.

========== 2014.01.01 00:00:21 remo-con disconnect======
Packet: P3S_FW_V01.06.0040.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.

P3S_FW_LOG_AB - Hidden File

[02076003]========== remo-con disconnect. boot(15) ============
[02076157]Packet [C:\P3S_FW_V01.06.0040.bin] detected, card sn [0x28539bff].
[02076197]Packet upgrade start...

[02076238]Packet checking...
[02076279]Packet vlink 01.06.0040 <-> 01.05.0030.
[02076360]Done.

[02076398]Version checking[1]...
[02088938][03 05][00] device not detected.
[02101479][03 06][00] device not detected.
[02101549][04 00][00] v1.40.0.0 -> v1.41.0.0 need upgrade.
[02114088][11 00][00] device not detected.
[02126633][12 00][00] device not detected.
[02139179][12 01][00] device not detected.
[02151737][12 02][00] device not detected.
[02164275][12 03][00] device not detected.
[02186818][15 00][00] device not detected.
[02199372][17 00][00] device not detected.
[02211918][17 01][00] device not detected.
[02224468][19 00][00] device not detected.
[02224509][01 00][00] v1.20.3419 -> v1.22.4095 need upgrade
[02224547][01 01][00] v1.20.3419 -> v1.22.4095 need upgrade
[02237086][09 00][00] device not detected.
[02237130]Done.

[02239179]Waiting for user confirm...
[02249219]Timeout, start upgrade automatically.

[02249302]Firmware upgrading[1]...
[02261828][01 00] Firmware upgrade start...
[00021735][01 00] Firmware upgrade finished successfully.
[00021781]Done.

[00021817]Packet [C:\P3S_FW_V01.06.0040.bin] resumed, card sn [0x28539bff].
[00021861]Packet vlink 01.06.0040 <-> 01.05.0030.
[00021931]Version checking[2]...
[00034480][03 05][00] device not detected.
[00047026][03 06][00] device not detected.
[00047076][04 00][00] v1.40.0.0 -> v1.41.0.0 need upgrade.
[00059616][11 00][00] device not detected.
[00072159][12 00][00] device not detected.
[00084699][12 01][00] device not detected.
[00097243][12 02][00] device not detected.
[00109788][12 03][00] device not detected.
[00132330][15 00][00] device not detected.
[00144870][17 00][00] device not detected.
[00157411][17 01][00] device not detected.
[00169951][19 00][00] device not detected.
[00169991][01 00][05] v1.22.4095 -> v1.22.4095
[00170138][01 01][00] v1.20.3419 -> v1.22.4095 need upgrade
[00182694][09 00][00] device not detected.
[00182737]Done.

[00182781]Firmware upgrading[2]...
[00182947][01 01] Firmware upgrade start...
[00213332][01 01] Firmware upgrade finished successfully.
[00213453][04 00] Firmware upgrade start...
[00272284][04 00] Firmware upgrade finished successfully.
[00272327]Done.

[00272371]Version checking[3]...
[00284911][03 05][00] device not detected.
[00297458][03 06][00] device not detected.
[00297509][04 00][05] v1.41.0.0 -> v1.41.0.0
[00310059][11 00][00] device not detected.
[00322601][12 00][00] device not detected.
[00335147][12 01][00] device not detected.
[00347692][12 02][00] device not detected.
[00360238][12 03][00] device not detected.
[00382799][15 00][00] device not detected.
[00395340][17 00][00] device not detected.
[00407886][17 01][00] device not detected.
[00420432][19 00][00] device not detected.
[00420474][01 00][05] v1.22.4095 -> v1.22.4095
[00420525][01 01][05] v1.22.4095 -> v1.22.4095
[00433078][09 00][00] device not detected.
[00433119]Packet upgrade failed at version checking.



[00022467]========== remo-con disconnect. boot(15) ============
[00022507]Packet [C:\P3S_FW_V01.06.0040.bin] detected, card sn [0x28539bff].
[00022551]Packet upgrade start...

[00022595]Packet checking...
[00022639]Packet vlink 01.06.0040 <-> 01.05.0030.
[00022710]Done.

[00022751]Version checking[1]...
[00035302][03 05][00] device not detected.
[00047844][03 06][00] device not detected.
[00047895][04 00][00] v1.41.0.0 -> v1.41.0.0
[00060436][11 00][00] device not detected.
[00072974][12 00][00] device not detected.
[00085520][12 01][00] device not detected.
[00098061][12 02][00] device not detected.
[00110606][12 03][00] device not detected.
[00133148][15 00][00] device not detected.
[00145689][17 00][00] device not detected.
[00158231][17 01][00] device not detected.
[00170775][19 00][00] device not detected.
[00170941][01 00][00] v1.22.4095 -> v1.22.4095
[00170983][01 01][00] v1.22.4095 -> v1.22.4095
[00183525][09 00][00] device not detected.
[00183567]Packet upgrade failed at version checking.



[00022008]========== remo-con disconnect. boot(15) ============
[00022050]Packet [C:\P3S_FW_V01.06.0040.bin] detected, card sn [0x28539bff].
[00022097]Packet upgrade start...

[00022143]Packet checking...
[00022186]Packet vlink 01.06.0040 <-> 01.05.0030.
[00022264]Done.


2015-12-28
Use props
DJI-Ken
DJI team
Flight distance : 1515312 ft
  • >>>
United States
Offline

john.gual Posted at 2015-12-29 04:51
Ken,

I am running a new iPad Air 2 with updated iOS which is on the DJI list.  I followed the abov ...

try one more time, reformat the SD card from your computer, then download the 1.6 again from the Phantom Pro page http://www.dji.com/product/phantom-3-pro/info#downloads
Put only the BIN file on the card, then instead of pulling the SD card right out, make sure to right click and eject. or eject with MAC.
Then put the SD card in and only power up the Phantom (make sure the battery is at least half charged)
it should make a bunch of beeps for just under a minute or so then go into the update mode and the beeps will be DDDD-DDDD-DDDD-DDDD and it will do that for a while and the gimbal light will flash red/green, then if successful (could be 20-30 minutes) the beeps will go to D-DD, D-DD D-DD and so on.
IF after you do all that and it still will not update, then copy the TXT file and post it here. If you still have no video, it will have to come in for warranty repair.
Here's a video of the entire duration of 1.6 update on a P3 Pro.
2015-12-28
Use props
nollzr
lvl.4
Flight distance : 701224 ft
  • >>>
United States
Offline

Same thing of me on my brand new..never flown phantom 3. App freezes in video mode...C1 C2 buttons dont seem to work unless you re calibrate the RC. I think its up to Dji to sort this one out and fix the App after the new update.
2015-12-28
Use props
russhog1
lvl.3
Flight distance : 680787 ft
  • >>>
United States
Offline

Same issue here. I'm a dealer, my demo unit worked fine before the latest firmware upgrade. I downloaded on Dec 25th from DJI. Update ran normally. No video after upgrade. I check my inspire 1 using same app, iPad and cable. The inspire 1 works fine. I have not installed the latest firmware on the Inspire 1.
2015-12-28
Use props
lperry17
New

United States
Offline

Tried to update firmware to a lower version 1.4 etc and that didn't work either.  Product still flies, no camera and inability to update the firmware.  Not so Happy Christmas Gift.  Any help would be appreciated.
2015-12-28
Use props
kjone33
lvl.2

United States
Offline

I am experiencing the same exact problem as everyone else after the latest firmware update.  The gimbal becomes unresponsive yet you can fly and all telemetry is fine.  Additionally video and pictures can be taken.  I can reboot the app and power on and off the drone and controller and app and only sometimes will it function 100%.  prior to this last firmware
2015-12-28
Use props
nollzr
lvl.4
Flight distance : 701224 ft
  • >>>
United States
Offline

DjDji has told me by email to downgrade back to firmware 1.5 to see if that fixes the no signal and app freezing when trying to record video . Since I haven't even flown mine yet, I'm a bit  hesitant to do this.
2015-12-29
Use props
eldreds
lvl.2
Flight distance : 81545 ft
Australia
Offline

Four flights so far and I now have the 'No Signal' issue. Phantom starts up and exercises the gimbal, and Signal comes up momentarily (but not every time). Gimbal flops down, video signal lost. I upgraded to the latest firmware OK two days ago.

Now the interesting bit and one that may explain why people can't load the firmware, is that when I connect the USB cable from PC to camera the connection is dropping in and out every few seconds. I'm also seeing the led on the front edge of the camera mount switching from green to red. So my two cents worth is that its nothing to do with IPad or other devices or their apps, it's the camera firmware.
2015-12-29
Use props
PP3-John
lvl.1

United States
Offline

I went through the entire process last night of trying to downgrade the firmware.  Tried every packet from 1.03 thru 1.05 and nothing worked.  I also tried to rerun 1.06 several times still with no success.  Apparently the machine is doing some updating because the app told me one of my batteries needed the firmware upgraded and that issue went away after trying the 1.06.  Overall though I still have never been able to complete one successful firmware update.  According to the log file, it shows the upgrade running and then failing due to version check.  The app says I have the most current firmware though.  Even with that said I still do not have a video feed.  I tried relinking the RC to the craft a couple times, uninstalling and reinstalling the app, nothing fixed the issue.  I called my dealer and they said they would exchange this with unit for another new one, so I think this is my best bet for now.  I don't want to wait three weeks or more for warranty service.  Hopefully the new one won't have the same issues.  I will post the results after I get it set up.  
2015-12-29
Use props
kjone33
lvl.2

United States
Offline

I am almost certain it is firmware related as I had zero issues before updating.  Video feed has become
2015-12-29
Use props
john.gual
lvl.1

United States
Offline

DJI-Ken Posted at 2015-12-28 16:08
try one more time, reformat the SD card from your computer, then download the 1.6 again from the P ...

No luck.  I followed the instructions and got 30 seconds of alternating red/green indicator light with D-D-D beeps, then a constant beep with a solid red light.  I left it that way for 3 minutes more before shutting down.  I still have a red "No Signal" indicator and no live video feed. There are two txt files.
The first file is in the root directory P3X_FW_RESULT_AB.txt  :

Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.

========== 2014.01.01 00:01:04 remo-con disconnect======
Packet: P3X_FW_V01.06.0040.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.

========== 2014.01.01 00:00:14 remo-con disconnect======
Packet: P3X_FW_V01.06.0040.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.

========== 2014.01.01 00:00:14 remo-con disconnect======
Packet: P3X_FW_V01.06.0040.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.

========== 2014.01.01 00:00:14 remo-con disconnect======
Packet: P3X_FW_V01.06.0040.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.

========== 2014.01.01 00:00:14 remo-con disconnect======
Packet: P3X_FW_V01.05.0030.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.

========== 2014.01.01 00:00:14 remo-con disconnect======
Packet: P3X_FW_V01.06.0040.bin
Upgrading ...
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.

========== 2015.12.24 15:02:24 =====================
Packet: P3X_FW_V01.06.0040.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.

========== 2014.01.01 00:04:36 remo-con disconnect======
Packet: P3X_FW_V01.06.0040.bin

========== 2014.01.01 00:00:14 remo-con disconnect======
Packet: P3X_FW_V01.06.0040.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.

========== 2015.12.24 19:59:54 =====================
Packet: P3X_FW_V01.06.0040.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.

========== 2015.12.25 09:10:49 =====================
Packet: P3X_FW_V01.06.0040.bin

========== 2015.12.25 09:12:11 =====================
Packet: P3X_FW_V01.06.0040.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.

========== 2015.12.25 09:33:53 =====================
Packet: P3X_FW_V01.06.0040.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.

========== 2014.01.01 00:00:14 remo-con disconnect======
Packet: P3X_FW_V01.04.0010.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.

========== 2014.01.01 00:00:14 remo-con disconnect======
Packet: P3X_FW_V01.04.0010.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.

========== 2015.12.25 12:58:09 =====================
Packet: P3X_FW_V01.04.0010.bin

========== 2015.12.25 12:58:58 =====================
Packet: P3X_FW_V01.04.0010.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.

========== 2014.01.01 00:00:14 remo-con disconnect======
Packet: P3X_FW_V01.06.0040.bin
Result: Failed.
Reboot the aircraft and try to upgrade the firmware again.


ALSO:   There is a second txt file:  MISC>LOG> P3X_FW_AB.txt  and here is what it contains:

[00014232][01 00] Firmware upgrade finished successfully.
[00014348]Done.

[00014381]Packet [C:\P3X_FW_V01.06.0040.bin] resumed, card sn [0x2810ef61].
[00014422]Packet vlink 01.06.0040 <-> 01.05.0030.
[00014485]Version checking[2]...
[00014562][03 05][00] v34.2.0.9 -> v34.2.0.9
[00014643][03 06][00] v2.1.6.18 -> v2.4.10.7 need upgrade.
[00014680][04 00][00] v1.38.0.0 -> v1.41.0.0 need upgrade.
[00014784][11 00][00] v1.6.1.0 -> v1.7.15.1 need upgrade.
[00014875][12 00][00] v1.8.0.0 -> v1.10.0.0 need upgrade.
[00014947][12 01][00] v1.8.0.0 -> v1.10.0.0 need upgrade.
[00015038][12 02][00] v1.8.0.0 -> v1.10.0.0 need upgrade.
[00015117][12 03][00] v1.8.0.0 -> v1.10.0.0 need upgrade.
[00027653][15 00][00] device not detected.
[00027738][17 00][00] v1.1.1.2 -> v1.1.1.7 need upgrade.
[00027878][17 01][00] v1.0.2.4 -> v1.0.2.7 need upgrade.
[00027926][19 00][00] v1.0.8.96 -> v1.0.8.96
[00027957][01 00][05] v1.26.4315 -> v1.26.4315
[00027988][01 01][00] v1.6.2736 -> v1.26.4315 need upgrade
[00040517][08 00][00] device not detected.
[00040570][09 00][00] v1.7.0.3 -> v2.13.0.0 need upgrade.
[00040605]Done.

[00040640]Firmware upgrading[2]...
[00040785][01 01] Firmware upgrade start...
[00071051][01 01] Firmware upgrade finished successfully.
[00071106][12 00] Firmware upgrade start...
[00139694][12 00] Firmware upgrade finished successfully.
[00139746][12 01] Firmware upgrade start...
[00210003][12 01] Firmware upgrade finished successfully.
[00210049][12 02] Firmware upgrade start...
[00277653][12 02] Firmware upgrade finished successfully.
[00277704][12 03] Firmware upgrade start...
[00343756][12 03] Firmware upgrade finished successfully.
[00343814][17 00] Firmware upgrade start...
[00478492][17 00] Firmware upgrade finished successfully.
[00478548][17 01] Firmware upgrade start...
[00558522][17 01] Firmware upgrade finished successfully.
[00558562][11 00] Firmware upgrade start...
[00610777][11 00] Firmware upgrade finished successfully.
[00611006][03 06] Firmware upgrade start...
[00943813][03 06] Firmware upgrade finished successfully.
[00943874][09 00] Firmware upgrade start...
[00997452][09 00] Firmware upgrade finished successfully.
[00997511][04 00] Firmware upgrade start...
[01056742][04 00] Firmware upgrade finished successfully.
[01056776]Done.

[01056807]Version checking[3]...
[01056887][03 05][00] v34.2.0.9 -> v34.2.0.9
[01056971][03 06][05] v2.4.10.7 -> v2.4.10.7
[01057010][04 00][05] v1.41.0.0 -> v1.41.0.0
[01057127][11 00][05] v1.7.15.1 -> v1.7.15.1
[01057226][12 00][05] v1.10.0.0 -> v1.10.0.0
[01057326][12 01][05] v1.10.0.0 -> v1.10.0.0
[01057426][12 02][05] v1.10.0.0 -> v1.10.0.0
[01057527][12 03][05] v1.10.0.0 -> v1.10.0.0
[01070066][15 00][00] device not detected.
[01070156][17 00][05] v1.1.1.7 -> v1.1.1.7
[01070282][17 01][05] v1.0.2.7 -> v1.0.2.7
[01070326][19 00][00] v1.0.8.96 -> v1.0.8.96
[01070359][01 00][05] v1.26.4315 -> v1.26.4315
[01070392][01 01][05] v1.26.4315 -> v1.26.4315
[01082936][08 00][00] device not detected.
[01082988][09 00][05] v2.13.0.0 -> v2.13.0.0
[01083021]Packet upgrade failed at version checking.



[00064431]========== remo-con disconnect. boot(15) ============
[00064465]Packet [C:\P3X_FW_V01.06.0040.bin] detected, card sn [0x2810ef61].
[00064515]Packet upgrade start...

[00064554]Packet checking...
[00064589]Packet vlink 01.06.0040 <-> 01.05.0030.
[00064658]Done.

[00064689]Version checking[1]...
[00064758][03 05][00] v34.2.0.9 -> v34.2.0.9
[00064838][03 06][00] v2.4.10.7 -> v2.4.10.7
[00064876][04 00][00] v1.41.0.0 -> v1.41.0.0
[00064998][11 00][00] v1.7.15.1 -> v1.7.15.1
[00065098][12 00][00] v1.10.0.0 -> v1.10.0.0
[00065203][12 01][00] v1.10.0.0 -> v1.10.0.0
[00065298][12 02][00] v1.10.0.0 -> v1.10.0.0
[00065398][12 03][00] v1.10.0.0 -> v1.10.0.0
[00077933][15 00][00] device not detected.
[00078033][17 00][00] v1.1.1.7 -> v1.1.1.7
[00078148][17 01][00] v1.0.2.7 -> v1.0.2.7
[00078198][19 00][00] v1.0.8.96 -> v1.0.8.96
[00078320][01 00][00] v1.26.4315 -> v1.26.4315
[00078364][01 01][00] v1.26.4315 -> v1.26.4315
[00090897][08 00][00] device not detected.
[00090959][09 00][00] v2.13.0.0 -> v2.13.0.0
[00090994]Packet upgrade failed at version checking.



[00014447]========== remo-con disconnect. boot(15) ============
[00014480]Packet [C:\P3X_FW_V01.06.0040.bin] detected, card sn [0x2810ef61].
[00014512]Packet upgrade start...

[00014550]Packet checking...
[00014590]Packet vlink 01.06.0040 <-> 01.05.0030.
[00014660]Done.

[00014692]Version checking[1]...
[00014752][03 05][00] v34.2.0.9 -> v34.2.0.9
[00014812][03 06][00] v2.4.10.7 -> v2.4.10.7
[00014858][04 00][00] v1.41.0.0 -> v1.41.0.0
[00014952][11 00][00] v1.7.15.1 -> v1.7.15.1
[00015021][12 00][00] v1.10.0.0 -> v1.10.0.0
[00015100][12 01][00] v1.10.0.0 -> v1.10.0.0
[00015176][12 02][00] v1.10.0.0 -> v1.10.0.0
[00015242][12 03][00] v1.10.0.0 -> v1.10.0.0
[00027776][15 00][00] device not detected.
[00027858][17 00][00] v1.1.1.7 -> v1.1.1.7
[00027982][17 01][00] v1.0.2.7 -> v1.0.2.7
[00028042][19 00][00] v1.0.8.96 -> v1.0.8.96
[00028074][01 00][00] v1.26.4315 -> v1.26.4315
[00028113][01 01][00] v1.26.4315 -> v1.26.4315
[00040648][08 00][00] device not detected.
[00040703][09 00][00] v2.13.0.0 -> v2.13.0.0
[00040738]Packet upgrade failed at version checking.



[00014838]========== remo-con disconnect. boot(15) ============
[00014872]Packet [C:\P3X_FW_V01.06.0040.bin] detected, card sn [0x2810ef61].
[00014907]Packet upgrade start...

[00014956]Packet checking...
[00014992]Packet vlink 01.06.0040 <-> 01.05.0030.
[00015058]Done.

[00015097]Version checking[1]...
[00015170][03 05][00] v34.2.0.9 -> v34.2.0.9
[00015225][03 06][00] v2.4.10.7 -> v2.4.10.7
[00015272][04 00][00] v1.41.0.0 -> v1.41.0.0
[00015387][11 00][00] v1.7.15.1 -> v1.7.15.1
[00015479][12 00][00] v1.10.0.0 -> v1.10.0.0
[00015554][12 01][00] v1.10.0.0 -> v1.10.0.0
[00015635][12 02][00] v1.10.0.0 -> v1.10.0.0
[00015726][12 03][00] v1.10.0.0 -> v1.10.0.0
[00028341][15 00][00] device not detected.
[00028438][17 00][00] v1.1.1.7 -> v1.1.1.7
[00028555][17 01][00] v1.0.2.7 -> v1.0.2.7
[00028615][19 00][00] v1.0.8.96 -> v1.0.8.96
[00028651][01 00][00] v1.26.4315 -> v1.26.4315
[00028686][01 01][00] v1.26.4315 -> v1.26.4315
[00041222][08 00][00] device not detected.
[00041276][09 00][00] v2.13.0.0 -> v2.13.0.0
[00041318]Packet upgrade failed at version checking.



[00015098]========== remo-con disconnect. boot(15) ============
[00015136]Packet [C:\P3X_FW_V01.06.0040.bin] detected, card sn [0x2810ef61].
[00015171]Packet upgrade start...

[00015208]Packet checking...
[00015251]Packet vlink 01.06.0040 <-> 01.05.0030.
[00015314]Done.

[00015349]Version checking[1]...
[00015435][03 05][00] v34.2.0.9 -> v34.2.0.9
[00015511][03 06][00] v2.4.10.7 -> v2.4.10.7
[00015553][04 00][00] v1.41.0.0 -> v1.41.0.0
[00015692][11 00][00] v1.7.15.1 -> v1.7.15.1
[00015775][12 00][00] v1.10.0.0 -> v1.10.0.0
[00015869][12 01][00] v1.10.0.0 -> v1.10.0.0
[00015969][12 02][00] v1.10.0.0 -> v1.10.0.0
[00016074][12 03][00] v1.10.0.0 -> v1.10.0.0
[00028609][15 00][00] device not detected.
[00028697][17 00][00] v1.1.1.7 -> v1.1.1.7
[00028816][17 01][00] v1.0.2.7 -> v1.0.2.7
[00028867][19 00][00] v1.0.8.96 -> v1.0.8.96
[00028903][01 00][00] v1.26.4315 -> v1.26.4315
[00028944][01 01][00] v1.26.4315 -> v1.26.4315
[00041478][08 00][00] device not detected.
[00041548][09 00][00] v2.13.0.0 -> v2.13.0.0
[00041587]Packet upgrade failed at version checking.



[00014871]========== remo-con disconnect. boot(15) ============
[00014915]Packet [C:\P3X_FW_V01.05.0030.bin] detected, card sn [0x2810ef61].
[00014954]Packet upgrade start...

[00014991]Packet checking...
[00015029]Packet vlink 01.05.0030 <-> 01.04.0010.
[00015102]Done.

[00015135]Version checking[1]...
[00015206][03 05][00] v34.2.0.9 -> v34.2.0.9
[00015287][03 06][00] v2.4.10.7 -> v2.4.0.5
[00015326][04 00][00] v1.41.0.0 -> v1.41.0.0
[00015526][11 00][00] v1.7.0.0 -> v1.7.0.0
[00015600][12 00][00] v1.10.0.0 -> v1.10.0.0
[00015676][12 01][00] v1.10.0.0 -> v1.10.0.0
[00015759][12 02][00] v1.10.0.0 -> v1.10.0.0
[00015847][12 03][00] v1.10.0.0 -> v1.10.0.0
[00028383][15 00][00] device not detected.
[00028458][17 00][00] v1.1.1.7 -> v1.1.1.7
[00028591][17 01][00] v1.0.2.7 -> v1.0.2.7
[00028657][19 00][00] v1.0.8.96 -> v1.0.8.96
[00028693][01 00][00] v1.26.4315 -> v1.26.4315
[00028730][01 01][00] v1.26.4315 -> v1.26.4315
[00041284][08 00][00] device not detected.
[00041357][09 00][00] v2.13.0.0 -> v2.13.0.0
[00041393]Packet upgrade failed at version checking.



[00014784]========== remo-con disconnect. boot(15) ============
[00014822]Packet [C:\P3X_FW_V01.06.0040.bin] detected, card sn [0x2810ef61].
[00014856]Packet upgrade start...

[00014896]Packet checking...
[00014938]Packet vlink 01.06.0040 <-> 01.05.0030.
[00015007]Done.

[00015045]Version checking[1]...
[00015109][03 05][00] v34.2.0.9 -> v34.2.0.9
[00015189][03 06][00] v2.4.10.7 -> v2.4.10.7
[00015247][04 00][00] v1.41.0.0 -> v1.41.0.0
[00015369][11 00][00] v1.7.0.0 -> v1.7.15.1 need upgrade.
[00015442][12 00][00] v1.10.0.0 -> v1.10.0.0
[00015517][12 01][00] v1.10.0.0 -> v1.10.0.0
[00015597][12 02][00] v1.10.0.0 -> v1.10.0.0
[00015688][12 03][00] v1.10.0.0 -> v1.10.0.0
[00028226][15 00][00] device not detected.
[00028314][17 00][00] v1.1.1.7 -> v1.1.1.7
[00028439][17 01][00] v1.0.2.7 -> v1.0.2.7
[00028494][19 00][00] v1.0.8.96 -> v1.0.8.96
[00028534][01 00][00] v1.26.4315 -> v1.26.4315
[00028570][01 01][00] v1.26.4315 -> v1.26.4315
[00041117][08 00][00] device not detected.
[00041175][09 00][00] v2.13.0.0 -> v2.13.0.0
[00041209]Done.

[00043249]Waiting for user confirm...
[00053289]Timeout, start upgrade automatically.

[00053371]Firmware upgrading[1]...
[00053416][11 00] Firmware upgrade start...
[00099229][11 00] Firmware upgrade finished successfully.
[00099268]Done.

[00099305]Version checking[2]...
[00099474][03 05][00] v34.2.0.9 -> v34.2.0.9
[00099554][03 06][00] v2.4.10.7 -> v2.4.10.7
[00099597][04 00][00] v1.41.0.0 -> v1.41.0.0
[00099714][11 00][05] v1.7.15.1 -> v1.7.15.1
[00099805][12 00][00] v1.10.0.0 -> v1.10.0.0
[00099902][12 01][00] v1.10.0.0 -> v1.10.0.0
[00099982][12 02][00] v1.10.0.0 -> v1.10.0.0
[00100078][12 03][00] v1.10.0.0 -> v1.10.0.0
[00112615][15 00][00] device not detected.
[00112702][17 00][00] v1.1.1.7 -> v1.1.1.7
[00112823][17 01][00] v1.0.2.7 -> v1.0.2.7
[00112878][19 00][00] v1.0.8.96 -> v1.0.8.96
[00112922][01 00][00] v1.26.4315 -> v1.26.4315
[00112959][01 01][00] v1.26.4315 -> v1.26.4315
[00125497][08 00][00] device not detected.
[00125560][09 00][00] v2.13.0.0 -> v2.13.0.0
[00125594]Packet upgrade failed at version checking.



[00015138]========== 2015.12.24 15:02:25. boot(15) ============
[00015176]Packet [C:\P3X_FW_V01.06.0040.bin] detected, card sn [0x2810ef61].
[00015211]Packet upgrade start...

[00015255]Packet checking...
[00015298]Packet vlink 01.06.0040 <-> 01.05.0030.
[00015364]Done.

[00015404]Version checking[1]...
[00015485][03 05][00] v34.2.0.9 -> v34.2.0.9
[00015569][03 06][00] v2.4.10.7 -> v2.4.10.7
[00015612][04 00][00] v1.41.0.0 -> v1.41.0.0
[00015722][11 00][00] v1.7.15.1 -> v1.7.15.1
[00015815][12 00][00] v1.10.0.0 -> v1.10.0.0
[00015890][12 01][00] v1.10.0.0 -> v1.10.0.0
[00015986][12 02][00] v1.10.0.0 -> v1.10.0.0
[00016086][12 03][00] v1.10.0.0 -> v1.10.0.0
[00028625][15 00][00] device not detected.
[00028710][17 00][00] v1.1.1.7 -> v1.1.1.7
[00028827][17 01][00] v1.0.2.7 -> v1.0.2.7
[00028883][19 00][00] v1.0.8.96 -> v1.0.8.96
[00028925][01 00][00] v1.26.4315 -> v1.26.4315
[00028961][01 01][00] v1.26.4315 -> v1.26.4315
[00041498][08 00][00] device not detected.
[00041558][09 00][00] v2.13.0.0 -> v2.13.0.0
[00041601]Packet upgrade failed at version checking.



[00276480]========== remo-con disconnect. boot(15) ============
[00276515]Packet [C:\P3X_FW_V01.06.0040.bin] detected, card sn [0x2850f06a].
[00276653]Packet upgrade start...

[00276701]Packet checking...
[00276738]Packet vlink 01.06.0040 <-> 01.05.0030.
[00276807]Done.

[00276848]Version checking[1]...
[00276922][03 05][00] v34.2.0.9 -> v34.2.0.9
[00277002][03 06][00] v2.4.10.7 -> v2.4.10.7
[00277058][04 00][00] v1.41.0.0 -> v1.41.0.0
[00277183][11 00][00] v1.7.15.1 -> v1.7.15.1
[00277296][12 00][00] v1.10.0.0 -> v1.10.0.0
[00277370][12 01][00] v1.10.0.0 -> v1.10.0.0
[00277450][12 02][00] v1.10.0.0 -> v1.10.0.0
[00277541][12 03][00] v1.10.0.0 -> v1.10.0.0
[00014904]========== remo-con disconnect. boot(15) ============
[00014947]Packet [C:\P3X_FW_V01.06.0040.bin] detected, card sn [0x2850f06a].
[00014984]Packet upgrade start...

[00015029]Packet checking...
[00015068]Packet vlink 01.06.0040 <-> 01.05.0030.
[00015137]Done.

[00015175]Version checking[1]...
[00015236][03 05][00] v34.2.0.9 -> v34.2.0.9
[00015315][03 06][00] v2.4.10.7 -> v2.4.10.7
[00015362][04 00][00] v1.41.0.0 -> v1.41.0.0
[00015475][11 00][00] v1.7.15.1 -> v1.7.15.1
[00015555][12 00][00] v1.10.0.0 -> v1.10.0.0
[00015646][12 01][00] v1.10.0.0 -> v1.10.0.0
[00015735][12 02][00] v1.10.0.0 -> v1.10.0.0
[00015810][12 03][00] v1.10.0.0 -> v1.10.0.0
[00028350][15 00][00] device not detected.
[00028426][17 00][00] v1.1.1.7 -> v1.1.1.7
[00028546][17 01][00] v1.0.2.7 -> v1.0.2.7
[00028605][19 00][00] v1.0.8.96 -> v1.0.8.96
[00028646][01 00][00] v1.26.4315 -> v1.26.4315
[00028687][01 01][00] v1.26.4315 -> v1.26.4315
[00041226][08 00][00] device not detected.
[00041286][09 00][00] v2.13.0.0 -> v2.13.0.0
[00041324]Packet upgrade failed at version checking.



[00015056]========== 2015.12.24 19:59:55. boot(15) ============
[00015099]Packet [C:\P3X_FW_V01.06.0040.bin] detected, card sn [0x2850f06a].
[00015136]Packet upgrade start...

[00015178]Packet checking...
[00015217]Packet vlink 01.06.0040 <-> 01.05.0030.
[00015297]Done.

[00015335]Version checking[1]...
[00015495][03 05][00] v34.2.0.9 -> v34.2.0.9
[00015581][03 06][00] v2.4.10.7 -> v2.4.10.7
[00015641][04 00][00] v1.41.0.0 -> v1.41.0.0
[00015759][11 00][00] v1.7.15.1 -> v1.7.15.1
[00015865][12 00][00] v1.10.0.0 -> v1.10.0.0
[00015967][12 01][00] v1.10.0.0 -> v1.10.0.0
[00016042][12 02][00] v1.10.0.0 -> v1.10.0.0
[00016146][12 03][00] v1.10.0.0 -> v1.10.0.0
[00028685][15 00][00] device not detected.
[00028783][17 00][00] v1.1.1.7 -> v1.1.1.7
[00028939][17 01][00] v1.0.2.7 -> v1.0.2.7
[00028997][19 00][00] v1.0.8.96 -> v1.0.8.96
[00029037][01 00][00] v1.26.4315 -> v1.26.4315
[00029077][01 01][00] v1.26.4315 -> v1.26.4315
[00041621][08 00][00] device not detected.
[00041691][09 00][00] v2.13.0.0 -> v2.13.0.0
[00041730]Packet upgrade failed at version checking.



[00252574]========== 2015.12.25 09:10:49. boot(15) ============
[00252608]Packet [C:\P3X_FW_V01.06.0040.bin] detected, card sn [0x00000000].
[00252642]Packet upgrade start...

[00252676]Packet upgrade failed at state checking (esc = 0).



[00015189]========== 2015.12.25 09:12:12. boot(0) ============
[00015233]Packet [C:\P3X_FW_V01.06.0040.bin] detected, card sn [0x2850f06a].
[00015277]Packet upgrade start...

[00015319]Packet checking...
[00015358]Packet vlink 01.06.0040 <-> 01.05.0030.
[00015430]Done.

[00015469]Version checking[1]...
[00015552][03 05][00] v34.2.0.9 -> v34.2.0.9
[00015633][03 06][00] v2.4.10.7 -> v2.4.10.7
[00015678][04 00][00] v1.41.0.0 -> v1.41.0.0
[00015813][11 00][00] v1.7.15.1 -> v1.7.15.1
[00015921][12 00][00] v1.10.0.0 -> v1.10.0.0
[00016023][12 01][00] v1.10.0.0 -> v1.10.0.0
[00016123][12 02][00] v1.10.0.0 -> v1.10.0.0
[00016223][12 03][00] v1.10.0.0 -> v1.10.0.0
[00028776][15 00][00] device not detected.
[00028859][17 00][00] v1.1.1.7 -> v1.1.1.7
[00028977][17 01][00] v1.0.2.7 -> v1.0.2.7
[00029031][19 00][00] v1.0.8.96 -> v1.0.8.96
[00029072][01 00][00] v1.26.4315 -> v1.26.4315
[00029116][01 01][00] v1.26.4315 -> v1.26.4315
[00041751][08 00][00] device not detected.
[00041818][09 00][00] v2.13.0.0 -> v2.13.0.0
[00041859]Packet upgrade failed at version checking.



[00044836]========== 2015.12.25 09:33:53. boot(15) ============
[00044876]Packet [C:\P3X_FW_V01.06.0040.bin] detected, card sn [0x2810ef61].
[00044917]Packet upgrade start...

[00044970]Packet checking...
[00045012]Packet vlink 01.06.0040 <-> 01.05.0030.
[00045084]Done.

[00045133]Version checking[1]...
[00045217][03 05][00] v34.2.0.9 -> v34.2.0.9
[00045298][03 06][00] v2.4.10.7 -> v2.4.10.7
[00045348][04 00][00] v1.41.0.0 -> v1.41.0.0
[00045459][11 00][00] v1.7.15.1 -> v1.7.15.1
[00045545][12 00][00] v1.10.0.0 -> v1.10.0.0
[00045638][12 01][00] v1.10.0.0 -> v1.10.0.0
[00045735][12 02][00] v1.10.0.0 -> v1.10.0.0
[00045838][12 03][00] v1.10.0.0 -> v1.10.0.0
[00058378][15 00][00] device not detected.
[00058462][17 00][00] v1.1.1.7 -> v1.1.1.7
[00058587][17 01][00] v1.0.2.7 -> v1.0.2.7
[00058657][19 00][00] v1.0.8.96 -> v1.0.8.96
[00058701][01 00][00] v1.26.4315 -> v1.26.4315
[00058743][01 01][00] v1.26.4315 -> v1.26.4315
[00071283][08 00][00] device not detected.
[00071358][09 00][00] v2.13.0.0 -> v2.13.0.0
[00071396]Packet upgrade failed at version checking.



[00014831]========== remo-con disconnect. boot(15) ============
[00014872]Packet [C:\P3X_FW_V01.04.0010.bin] detected, card sn [0x2810ef61].
[00014912]Packet upgrade start...

[00014963]Packet checking...
[00015004]Packet vlink 01.04.0010 <-> 01.03.0020.
[00015081]Done.

[00015126]Version checking[1]...
[00015211][03 05][00] v34.2.0.9 -> v34.2.0.9
[00015311][03 06][00] v2.4.10.7 -> v2.3.0.13
[00015364][04 00][00] v1.41.0.0 -> v1.41.0.0
[00015430][09 00][00] v2.13.0.0 -> v1.7.0.3
[00015550][11 00][00] v1.7.15.1 -> v1.7.0.0
[00015652][12 00][00] v1.10.0.0 -> v1.10.0.0
[00015750][12 01][00] v1.10.0.0 -> v1.10.0.0
[00015850][12 02][00] v1.10.0.0 -> v1.10.0.0
[00015950][12 03][00] v1.10.0.0 -> v1.10.0.0
[00028493][15 00][00] device not detected.
[00028700][17 00][00] v1.1.1.7 -> v1.1.1.7
[00028834][17 01][00] v1.0.2.7 -> v1.0.2.7
[00028890][19 00][00] v1.0.8.96 -> v1.0.8.96
[00028932][01 00][00] v1.26.4315 -> v1.23.3419
[00028978][01 01][00] v1.26.4315 -> v1.23.3419
[00041521][08 00][00] device not detected.
[00041563]Packet upgrade failed at version checking.



[00015173]========== remo-con disconnect. boot(15) ============
[00015218]Packet [C:\P3X_FW_V01.04.0010.bin] detected, card sn [0x2810ef61].
[00015267]Packet upgrade start...

[00015309]Packet checking...
[00015355]Packet vlink 01.04.0010 <-> 01.03.0020.
[00015427]Done.

[00015468]Version checking[1]...
[00015540][03 05][00] v34.2.0.9 -> v34.2.0.9
[00015605][03 06][00] v2.4.10.7 -> v2.3.0.13
[00015659][04 00][00] v1.41.0.0 -> v1.41.0.0
[00015714][09 00][00] v2.13.0.0 -> v1.7.0.3
[00015840][11 00][00] v1.7.15.1 -> v1.7.0.0
[00015941][12 00][00] v1.10.0.0 -> v1.10.0.0
[00016017][12 01][00] v1.10.0.0 -> v1.10.0.0
[00016115][12 02][00] v1.10.0.0 -> v1.10.0.0
[00016223][12 03][00] v1.10.0.0 -> v1.10.0.0
[00028773][15 00][00] device not detected.
[00028870][17 00][00] v1.1.1.7 -> v1.1.1.7
[00028990][17 01][00] v1.0.2.7 -> v1.0.2.7
[00029056][19 00][00] v1.0.8.96 -> v1.0.8.96
[00029098][01 00][00] v1.26.4315 -> v1.23.3419
[00029143][01 01][00] v1.26.4315 -> v1.23.3419
[00041685][08 00][00] device not detected.
[00041728]Packet upgrade failed at version checking.



[00015090]========== 2015.12.25 12:58:10. boot(15) ============
[00015138]Packet [C:\P3X_FW_V01.04.0010.bin] detected, card sn [0x2810ef61].
[00015181]Packet upgrade start...

[00015228]Packet checking...
[00015278]Packet vlink 01.04.0010 <-> 01.03.0020.
[00015350]Done.

[00015389]Version checking[1]...
[00015469][03 05][00] v34.2.0.9 -> v34.2.0.9
[00015570][03 06][00] v2.4.10.7 -> v2.3.0.13
[00015624][04 00][00] v1.41.0.0 -> v1.41.0.0
[00015680][09 00][00] v2.13.0.0 -> v1.7.0.3
[00015785][11 00][00] v1.7.15.1 -> v1.7.0.0
[00015960][12 00][00] v1.10.0.0 -> v1.10.0.0
[00016034][12 01][00] v1.10.0.0 -> v1.10.0.0
[00016134][12 02][00] v1.10.0.0 -> v1.10.0.0
[00016225][12 03][00] v1.10.0.0 -> v1.10.0.0
[00028775][15 00][00] device not detected.
[00028876][17 00][00] v1.1.1.7 -> v1.1.1.7
[00029016][17 01][00] v1.0.2.7 -> v1.0.2.7
[00029081][19 00][00] v1.0.8.96 -> v1.0.8.96
[00029129][01 00][00] v1.26.4315 -> v1.23.3419
[00029170][01 01][00] v1.26.4315 -> v1.23.3419
[00015190]========== 2015.12.25 12:58:59. boot(0) ============
[00015239]Packet [C:\P3X_FW_V01.04.0010.bin] detected, card sn [0x2810ef61].
[00015283]Packet upgrade start...

[00015332]Packet checking...
[00015375]Packet vlink 01.04.0010 <-> 01.03.0020.
[00015453]Done.

[00015495]Version checking[1]...
[00015568][03 05][00] v34.2.0.9 -> v34.2.0.9
[00015648][03 06][00] v2.4.10.7 -> v2.3.0.13
[00015697][04 00][00] v1.41.0.0 -> v1.41.0.0
[00015753][09 00][00] v2.13.0.0 -> v1.7.0.3
[00015868][11 00][00] v1.7.15.1 -> v1.7.0.0
[00015954][12 00][00] v1.10.0.0 -> v1.10.0.0
[00016055][12 01][00] v1.10.0.0 -> v1.10.0.0
[00016148][12 02][00] v1.10.0.0 -> v1.10.0.0
[00016250][12 03][00] v1.10.0.0 -> v1.10.0.0
[00028798][15 00][00] device not detected.
[00028896][17 00][00] v1.1.1.7 -> v1.1.1.7
[00029042][17 01][00] v1.0.2.7 -> v1.0.2.7
[00029113][19 00][00] v1.0.8.96 -> v1.0.8.96
[00029157][01 00][00] v1.26.4315 -> v1.23.3419
[00029200][01 01][00] v1.26.4315 -> v1.23.3419
[00041749][08 00][00] device not detected.
[00041795]Packet upgrade failed at version checking.



[00015241]========== remo-con disconnect. boot(15) ============
[00015281]Packet [C:\P3X_FW_V01.06.0040.bin] detected, card sn [0x2850f06a].
[00015330]Packet upgrade start...

[00015376]Packet checking...
[00015419]Packet vlink 01.06.0040 <-> 01.05.0030.
[00015497]Done.

[00015541]Version checking[1]...
[00015611][03 05][00] v34.2.0.9 -> v34.2.0.9
[00015711][03 06][00] v2.4.10.7 -> v2.4.10.7
[00015768][04 00][00] v1.41.0.0 -> v1.41.0.0
[00015975][11 00][00] v1.7.15.1 -> v1.7.15.1
[00016059][12 00][00] v1.10.0.0 -> v1.10.0.0
[00016139][12 01][00] v1.10.0.0 -> v1.10.0.0
[00016230][12 02][00] v1.10.0.0 -> v1.10.0.0
[00016330][12 03][00] v1.10.0.0 -> v1.10.0.0
[00028875][15 00][00] device not detected.
[00028966][17 00][00] v1.1.1.7 -> v1.1.1.7
[00029100][17 01][00] v1.0.2.7 -> v1.0.2.7
[00029185][19 00][00] v1.0.8.96 -> v1.0.8.96
[00029227][01 00][00] v1.26.4315 -> v1.26.4315
[00029271][01 01][00] v1.26.4315 -> v1.26.4315
[00041827][08 00][00] device not detected.
[00041885][09 00][00] v2.13.0.0 -> v2.13.0.0
[00041933]Packet upgrade failed at version checking.





2015-12-29
Use props
DJI-Ken
DJI team
Flight distance : 1515312 ft
  • >>>
United States
Offline

John,
From my earlier post it looks like you have Module 8 and 15 "Device Not Detected", unfortunately if trying everything and you still get no video you'll have to contact support and send it in for repair.
2015-12-29
Use props
john.gual
lvl.1

United States
Offline

DJI-Ken Posted at 2015-12-29 14:12
John,
From my earlier post it looks like you have Module 8 and 15 "Device Not Detected", unfortunat ...

Ken,  

Understood.  I tried the telephone support, but i was 47th in line....Holiday rush, I assume.  I wrote an email to support and will let you know what they say.
2015-12-29
Use props
DJI-Ken
DJI team
Flight distance : 1515312 ft
  • >>>
United States
Offline

john.gual Posted at 2015-12-30 06:13
Ken,  

Understood.  I tried the telephone support, but i was 47th in line....Holiday rush, I assu ...

Yes, it's extremely busy here. Supposedly 1 million drones under the Christmas tree with DJI probably having the most of them.
2015-12-29
Use props
PP3-John
lvl.1

United States
Offline

to all,  as posted earlier I decided to return the bird and swap it for another since my dealer said they would.  I hooked up the new one just a few minutes ago and it works, no issues, right out of the box.  I have video and all on my Galaxy Tab 4.  I followed some of the other posts about making sure you use the link in the DJI site for the go app and made sure the debugging was enabled.  I also killed a bunch of unnecessary apps.  The app is telling me the firmware is out of date for the RC and the bird.  With all the other posts from people having issues with the firmware upgrade to 1.06 I am very skeptical about performing the upgrade.  Especially with what happened with the first bird.  Was it the firmware or a bad bird?
2015-12-29
Use props
kjone33
lvl.2

United States
Offline

I downgraded my firmware to 1.5.3 and magically no more issues.  Have yet to fly it but prior to downgrading I tested the video and it would constantly drop out to the dji logo and take a good bit of time to re-establish video.  As soon as I,downgraded problem solved.  
2015-12-29
Use props
PP3-John
lvl.1

United States
Offline

New update...I decided to take my chances and roll the dice by doing the firmware update to 1.6 on the replacement craft.

I first started by checking the current versions.  The craft was sitting at 1.4 so I decided I would start with the 1.5 fw.  It ran successfully into the craft.  I then ran the fw upgrade for the RC through the app.  That also completed successfully.  I started up the controller and the craft and checked to make sure everything was ok before continuing - There were no issues, I had a video feed from craft and I was good to go.  The app did tell me the craft FW was out of date so i decided to go ahead with the 1.6 FW update.  It also ran successfully into the craft.  I restarted everything, and i currently have no issues.  I have a video feed and all green for current FW and flying.  So it appears that the first P3P craft I bought was a bad seed, the replacement one works perfectly so far after all the upgrades.  Oh, and I almost forgot, I am still using my Samsung Galaxy Tab 4 7.0 even though it is not on the approved list.  I will post if I end up having any issues.  Thanks to all who provided input and advice.
2015-12-30
Use props
fishcake919
lvl.1

United Kingdom
Offline

Hi All,
Same here.
Brand new P3 Pro.
Upgraded to latest FW prior to flying and screen goes blank and app drops out, also gimbal goes to approx. 45-60 degrees or face down and does not move. When trying to record video on the floor it stops recording after 7-10 seconds. Have spent the last three days upgrading downgradind, swopping devices ( all apple and new) swopping memory cards, formatting etc etc, whatever is being said on the forums etc etc. FW upgrade and downdrade all show success in log but camera and app go blank. Deleted app and re-installed numerous times.
The firmware installs with no issues both ways up and down but still hangs.
The model flies hovers and all control surfaces work but then the screen goes blank and stops.
Looks like I will have to replace the P3 for a new one as this isn't device related but is either firmware or actual P3 Pro.
Have upgraded and downgraded and sometimes it seems to work, I take model and try to fly and it just hangs again or camera locks in a strange position. Both back buttons do not work either.
Shame as this model looks awesome but not going to risk it, I have 30 years in RC helis, planes and gliders and fully researched before I bought the P3Pro.
Will wait till I get a new one.
Thanks
Lucas
2015-12-31
Use props
DJI-Ken
DJI team
Flight distance : 1515312 ft
  • >>>
United States
Offline

PP3-John Posted at 2015-12-30 11:32
to all,  as posted earlier I decided to return the bird and swap it for another since my dealer said ...

Some people with the older Phantoms had some vibrations but lowering the basic gains took care of most all. And a few had lost video signal from the module 8 and 15 not updating. If that cannot be corrected by multiple upgrades/downgrades then it would have to be sent in for repair.
What firmware is the aircraft on now, I would go ahead and update to 1.6.
2015-12-31
Use props
DJI-Ken
DJI team
Flight distance : 1515312 ft
  • >>>
United States
Offline

fishcake919 Posted at 2015-12-31 23:38
Hi All,
Same here.
Brand new P3 Pro.

It definitely seems like you are having more issues than most. Since you are using the latest Apple devices and tried several times to upgrade/downgrade and sometimes things work and sometimes they don't, my advice is contact support and send it in for warranty repair.Sorry you are having so many issues.
2015-12-31
Use props
fishcake919
lvl.1

United Kingdom
Offline

Thank you Ken.
I will take the model back and get it changed as it is brand new. Shame as my son and me were really looking forward to exploring with it but we will wait till a new one turns up. I am new to this but it does seem that an awful lot of people are having similar issues with the FW update.
The UK weather would of stopped us from flying most times anyway!

Happy New Year All.
2015-12-31
Use props
Cloud Kicker
lvl.1

Canada
Offline

I purchased my first DJI product a little over a month ago. A Phantom 3 Pro.

Starting it up for the first time the DJI GO app indicated that I needed to update firmware. It was below v1.3.20. I updated it all successfully to v1.5.30. Actually it shows Aircraft version 1.5.30 and RC version 1.5.70. Now the DJI GO app tells me to update again. I guess it's the v1.6.0040.

Reading about the issues people have after updating to v1.6.0040, is it worth trying the update or wait until DJI comes out with a new version where these bugs are fixed?
2016-1-9
Use props
Hawks100
Second Officer
Flight distance : 134580 ft
United Kingdom
Offline

The RC sometimes need to update the firmware through the App only.
I had a lot of trouble tying to connect another RC to my P3A.
Try turning on your Aircraft first,Press an hold the link button and then turn on the RC. Get to the LINK Screen, press ok to Link and release the link button on the Aircraft.This worked for me in the end.
Its worth a try.
Good luck.
2016-1-9
Use props
iamdorian
lvl.4
Flight distance : 68356 ft
  • >>>
United States
Offline

I had my bird offline since about December. Upgraded from (I suppose) 1.4 to the 1.06.0040 FW update. The RC started the process, prompting me, and then the FW update was required. So, In just began with 1.6 Ye Gods! Now the same exact problems as above plague my P3 as well. STUPID ME ... trusting a DJI FW update like that?!

A couple of people mentioned downgrading but this simply does not work for me, or I need a trick/technique I don;t know about? Is there some weird DJI-centric procedure for DOWNGRADING?

What a freakin' hassle!

Like others, I need this machine to work, not screw up after forced updates. Now I am afraid to update by I1 as well, for fear of a repeat.

For the P3, its next mission requires flying over water. I try not to fly the I1 over water, because I simply cannot afford a $3,500.00 loss! Loosing $1,200.00 (or whatever DJI has now reduced their prices for a P3 to) is not acceptable for me. What now?

Can anyone share their magical Firmware (1.6 => 1.5) Downgrading procedure with me ... I'd deeply appreciate it!?

Dorian

2016-2-29
Use props
iamdorian
lvl.4
Flight distance : 68356 ft
  • >>>
Offline

Personally I find it reprehensible that SO MANY CUSTOMERS are treated this way by DJI. They should fess up, offer a public apology and provide a work-around that does not require shipping costs, lost productivity and (of all things FEES) to fix something that shouldn't be breaking with a mere FW update!

It seems likely this is a LightBridge interface issue. What a hassle. I hope someone offers a saner solution than shipping to this bird back to Hong Kong? This is obviously a DJI problem. Someone whould warn people?
2016-2-29
Use props
iamdorian
lvl.4
Flight distance : 68356 ft
  • >>>
Offline

iamdorian Posted at 2016-3-1 06:15
Personally I find it reprehensible that SO MANY CUSTOMERS are treated this way by DJI. They should f ...

"Try turning on your Aircraft first,Press an hold the link button and then turn on the RC. Get to the LINK Screen, press ok to Link and release the link button on the Aircraft.This worked for me in the end."
2016-2-29
Use props
iamdorian
lvl.4
Flight distance : 68356 ft
  • >>>
United States
Offline

This did no good for me. Everything looks fine and is NOT.

/var/folders/xf/dfm_hlvn50zbllrllm4wgqlr0000gn/T//ImageWell/IMG_5484.jpg
2016-2-29
Use props
Advanced
You need to log in before you can reply Login | Register now

Credit Rules