Is it me or phone/tab holder is a bit wobbly and top screw is getting loose very easly which casing more wooble ?

This is a common issue. Some people buy andInspire 1 device holder - http://goo.gl/q8IBce - Another option is to remove the holder from the controller and putting a single wrap os sellotape ( scotch tape ) around the shaft ( a piece that just wraps one arund is all thats needed ). Works a treat. There is also a little alle key screw near where the shaft connects to the plastic holder that sometimes needs tightening.

Remember to buy extra propellers and one or two spare batteries to keep you flying

www.Phantom-Guide.co.uk - The Ultimate Phantom 3 Resource

its a nice tip

big thanks sploodge !

I tightened mine with needle nose pliers and haven't had any problems since. Just be careful not to over tighten.

Here's a detailed comparison between the Phantom 3 and Inspire 1 tablet mount:
http://www.phantompilots.com/thr ... -tablet-mount.42864

---

www.PhantomHelp.com
Find the latest must-haves, fixes, mods, how-tos, guides, and accessories for your Phantom.
Phantoms in stock and ready to ship worldwide! (see availability)

new samsung tab s2 is coming and it's supposed to be very thisn and light

Went ahead and ordered the Inspire 1 device holder.
It should help elevate and eleviate any iPad Air 2 64gb Cellular, wibble-wobble...

RedHotPoker

RedHotPoker Posted at 2015-6-7 00:34
Went ahead and ordered the Inspire 1 device holder.
It should help elevate any iPad mini wobble...

Just be cautioned that by making the mount firmer, you moved the point of failure from the bracket to the transmitter body.
Make sure that the barrel adjuster is tight before use. If you have an issue with the barrel loosening up excessively, take some clear nail polish and coat the thread and screw it back together. Thread lockers like Loctite  are too strong for small fasteners and will com[licate things if you ever need to get the bracket off.

There are numerous grades of thread-loctite products. Anyway, a hair blower, heating up the adhesive, loosens it right up.
I use it in all of my helicopter screws that need it,,, so know plenty about it. Not using nail polish or that kind of thing in RC.

Thanks for the tips, will be keeping my good eye on all screws and fasteners.

RedHotPoker

Align TREX 700E DFC HV~Spectrum DX8
DJI Phantom 3 Professional, Parrot AR Drone 2.0,
Blade mCPX BL, Blade mQX, Heli Max 1SQ~Spectrum DX6i, Traxxas QR-1, RealFlight 6.5

I have updated my SIG
Align TRex 700E DFC HV~Spektrum DX8 MAAC 91236
Blade mCPX BL Blade mQX DJI Phantom 3 Pro'~iPad Air 2 Cellular
Heli-Max Voltage 500 3D Heli-Max 1SQ~AnyLink~Spektrum DX6i
Parrot AR Drone 2.0 Traxxas QR-1 RealFlight 6.5

RedHotPoker Posted at 2015-6-8 00:47
There are numerous grades of thread lock-lock tite products. Anyway, a hair blower, heating up the a ...

I know this is an old thread, but I just got my Inspire Tablet Mount for my P3P and it didn't come with the short screw needed to fasten the end down. It is not the same size as the original screw, did you get one with yours? Thanks!
Argghhhh.  Never mind, I found it stashed away in some cardboard cut out thing. Sorry for bumping this up.

Barney

@Barney Rubbel,
Swell & good. Did you get the flat head driver in with yours too? ;-)
Very handy when you have to tighten down that awesome device holder again.
Yeah, it will loosen up some. In about 6 months. Hahaha
Ok carry on smiling, everybody.

Wheeee hahaha

RedHotPoker
Wish we had a forum SIG allowance...
Align TRex 700E DFC HV~Spektrum DX8 MAAC 91236
Blade mCPX BL Blade mQX DJI Phantom 3 Pro'~iPad Air 2 Cellular
Heli-Max Voltage 500 3D Heli-Max 1SQ~AnyLink~Spektrum DX6i
Parrot AR Drone 2.0 Traxxas QR-1 RealFlight 6.5