My DJI GO App won't connect anymore.


DJI GO (iOS): 2.7.1
iOS: 9.3.1
A/C Fw: 1.8.80 (via USB)
R/C Fw: ? (can't check, since I can't connect via DJI Go)


I first tried to upgrade via the DJI GO App (was already on 2.7.1), but A/C showed as "Disconnected". So, I figured there was a problem that the new app required the new firmware. Upgraded the A/C successfully via the MicroSD card to 1.8.80. Since then, I can't even connect to via DJI GO - only the "How to connect" button appears and therefore I can't upgrade the R/C at all.


R/C seems to link fine with the A/C (green light).


Any suggestions would be greatly appreciated!


Thank you!

I can give you the file to upgrade the RC via  a Thumb drive  if you like.  You will not be able to use the Aircraft until you have this loaded.  

please read my link and it will get you going.  I realise your RC is not bricked but if having trouble you can do it this way.  The RC is 1.6 and this is the file to download


I dont understand one part of your post.  when you are updating the RC make sure the aircraft is off, you dont want to connect.  Then just have   a wireless internet connection with the go app and rc on and it should tell you that there is an update.  (I would try this first, then you can use the thumb drive if you want).  You can open that GO APP , when the RC and I pad are connected and turned on near a wi - fi source ( MAKE SURE AIRCRAFT OFF )    Just tap on the  camera or equipment icon, it should open .  Then look for update in the "Aircraft Status" tab

donnie

http://forum.dji.com/thread-47577-1-1.html

Be sure to read my tips page also

http://forum.dji.com/thread-45630-1-1.html

donnie

Donnie Posted at 2016-4-11 22:16
I can give you the file to upgrade the RC via  a Thumb drive  if you like.  You will not be able to  ...

Thanks Donnie,

tried upgrading with the RC Update v1.6, but the RC (GL300B) won't upgrade. It's been sitting idle for 10 minutes with the red light on and then beeping because of the inactivity. It almost looks like the full USB port (have tried it on the mini-USB port) on the RC doesn't work at all. I haven't touched anything before the upgrade and haven't even flown it, so I doubt that the port will just go bad without even having touched it.

DJI Go won't connect at all. No upgrade notifications, nothing. It just sits have the main "Equipment" page and shows the "How to connect" button on all models. WLAN is on. Internet is fine. I have the P2A. Grrrr.

Thanks,
Patrick

Hi, I have the same issues and its been updated correctly! Bird off when doing the RC update.
I have a P3Advanced though.
Hope you get it sorted.

sandmark Posted at 2016-4-11 19:59
Hi, I have the same issues and its been updated correctly! Bird off when doing the RC update.
I have ...

I appear to be having the same connection problem, but for a different reason.  I upgraded to the latest firmware the other day and it all works fine with the iPhone6.  However, I bought an iPad Air 2 for a larger screen and now I can't get past the "How to Connect" screen.  I tried DJI Chat, but they got stuck on telling me to re-link the RC.  I don't know how to do that when I can't get into the software.

A very interesting point is I accidentally found out the software on the iPad Air 2 apparently recognizes my P-3-PRO as a P-3-Standard, which will let me into the software.  However, it shows the aircraft to be disconnected and if I try "Linking RC" from here it does nothing.  You click "are you sure you want to do this" and nothing happens.

From what you guys have said and what I've experienced, there may be a software glitch of some kind.

Hello, have you tried to other devices and original lightning cables to connect your RC?

East Side Kid Posted at 2016-4-12 08:48
I appear to be having the same connection problem, but for a different reason.  I upgraded to the  ...

Hi,
I purchased an iPad air 2 just for the P3A and Ive got the same (how to connect) screen.
I was flying it before I did the updates (correctly! sick of people suggesting its prob from the way it was done)
the app will open on my Sony phone but when I press the blue camera button it opens with a dark grey screen with the controls but no camera picture, Ive cot control between the RC and the Bird ,and everything in the app says its all up to date.
Nothing on the iPad as i cant connect to find out.

sandmark Posted at 2016-4-12 12:00
Hi,
I purchased an iPad air 2 just for the P3A and Ive got the same (how to connect) screen.
I wa ...

Couple of things, if it says how to connect on your iPad and not your Android phone you know the USB port is fine on the RC. try another USB cable.
You said everything is up to date RC 1.6, aircraft 1.8 correct?
Since you have connection with the RC and aircraft but no video. Does it say no signal?
lets look at the log file from when you updated the aircraft.
Can you post the hidden log file from the SD card and I can look it over.
Below are instructions on how to read the hidden files. If you have formatted the SD card, download 1.8 again from the P3 Advanced page and reattempt the firmware then post the hidden log file.

Windows system :
http://windows.microsoft.com/en- ... den-files=windows-7
Mac system :
http://ianlunn.co.uk/articles/qu ... mac-os-x-mavericks/

DJI Ken,
I just tried to reinstall the 1.8.80 to the Bird via the SD card. It failed.
I then got it to connect to my Sony device showing Video.
I thought I would make a video of it working on the Sony and then swap it to the iPad for you, so after shutting everything down, closing the Go app and then restarting everything, I could get every thing to work except the camera feed and yes it does now come up with (NO SIGNAL) in red.
I tried to connect multiple times but no camera feed (bugger is intermittent)
When I read the about info it tells me everything is up to date.
Bird 1.8.80
app 2.7.2
RC 1.6.0
When I connect the iPad it comes up with the How to connect page ( the cable is fine I just purchased 2 apple ones today and tested them on other devices.)
I know it seems like it but its not the cable.
As you can see by the Log the Device not detected keeps popping up and then comes good, I'm guessing when whatever it is that makes that go away for a second is the time when I can actually see the camera feed on the android device.
The camera feed was a bit hit and miss from day one ( Bought an iPad air 2 to try and solve it and it worked fine 2 out of 3 times or there about) I could live with that so I never really stressed over it.
Had a quick fly the other day and all theses updates warnings flashed on screen so I landed and did the updates correctly!!! and since then its a Paper weight.
The iPad is running  9.3.1
I do really appreciate the help but its really frustrating.
Just another thought when there is the Red No Signal display and I cant see the camera's live feed why is it that I can still control the camera , take pics , video to the SD card and adjust the gimbal up and down etc?


[00264188]========== remo-con disconnect. boot(2) ============
[00264335]Packet [C:\P3S_FW_V01.06.0040.bin] detected, card sn [0x016203e1].
[00264371]Packet upgrade start...

[00264412]Packet checking...
[00264456]Packet vlink 01.06.0040 <-> 01.05.0030.
[00264520]Done.

[00264557]Version checking[1]...
[00264625][03 05][00] v34.2.0.9 -> v34.2.0.9
[00264690][03 06][00] v2.4.0.4 -> v2.4.10.7 need upgrade.
[00264745][04 00][00] v1.41.0.0 -> v1.41.0.0
[00264866][11 00][00] v1.7.0.0 -> v1.7.15.1 need upgrade.
[00264944][12 00][00] v1.10.0.0 -> v1.10.0.0
[00265019][12 01][00] v1.10.0.0 -> v1.10.0.0
[00265096][12 02][00] v1.10.0.0 -> v1.10.0.0
[00265176][12 03][00] v1.10.0.0 -> v1.10.0.0
[00265211][15 00][00] v1.1.2.0 -> v1.1.2.0
[00265300][17 00][00] v1.1.1.7 -> v1.1.1.7
[00265420][17 01][00] v1.0.2.7 -> v1.0.2.7
[00265476][19 00][00] v1.0.8.96 -> v1.0.8.96
[00265510][01 00][00] v1.22.4095 -> v1.22.4095
[00265544][01 01][00] v1.22.4095 -> v1.22.4095
[00265596][09 00][00] v1.7.0.3 -> v2.13.0.0 need upgrade.
[00265629]Done.

[00012031]========== remo-con disconnect. boot(15) ============
[00012064]Packet [C:\P3S_FW_V01.06.0040.bin] detected, card sn [0x016203e1].
[00012100]Packet upgrade start...

[00012142]Packet checking...
[00012184]Packet vlink 01.06.0040 <-> 01.05.0030.
[00012252]Done.

[00012284]Version checking[1]...
[00012373][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012428][03 06][00] v2.4.0.4 -> v2.4.10.7 need upgrade.
[00012495][04 00][00] v1.41.0.0 -> v1.41.0.0
[00012629][11 00][00] v1.7.0.0 -> v1.7.15.1 need upgrade.
[00012731][12 00][00] v1.10.0.0 -> v1.10.0.0
[00012802][12 01][00] v1.10.0.0 -> v1.10.0.0
[00012882][12 02][00] v1.10.0.0 -> v1.10.0.0
[00012958][12 03][00] v1.10.0.0 -> v1.10.0.0
[00013004][15 00][00] v1.1.2.0 -> v1.1.2.0
[00013078][17 00][00] v1.1.1.7 -> v1.1.1.7
[00013198][17 01][00] v1.0.2.7 -> v1.0.2.7
[00013258][19 00][00] v1.0.8.96 -> v1.0.8.96
[00013301][01 00][00] v1.22.4095 -> v1.22.4095
[00013337][01 01][00] v1.22.4095 -> v1.22.4095
[00013518][09 00][00] v1.7.0.3 -> v2.13.0.0 need upgrade.
[00013556]Done.

[00015594]Waiting for user confirm...
[00025631]Timeout, start upgrade automatically.

[00025703]Firmware upgrading[1]...
[00025755][11 00] Firmware upgrade start...
[00071946][11 00] Firmware upgrade finished successfully.
[00072189][03 06] Firmware upgrade start...
[00424782][03 06] Firmware upgrade finished successfully.
[00424866][09 00] Firmware upgrade start...
[00478430][09 00] Firmware upgrade finished successfully.
[00478467]Done.

[00478503]Version checking[2]...
[00478594][03 05][00] v34.2.0.9 -> v34.2.0.9
[00478674][03 06][05] v2.4.10.7 -> v2.4.10.7
[00478721][04 00][00] v1.41.0.0 -> v1.41.0.0
[00478834][11 00][05] v1.7.15.1 -> v1.7.15.1
[00478930][12 00][00] v1.10.0.0 -> v1.10.0.0
[00479003][12 01][00] v1.10.0.0 -> v1.10.0.0
[00479083][12 02][00] v1.10.0.0 -> v1.10.0.0
[00479157][12 03][00] v1.10.0.0 -> v1.10.0.0
[00479199][15 00][00] v1.1.2.0 -> v1.1.2.0
[00479297][17 00][00] v1.1.1.7 -> v1.1.1.7
[00479427][17 01][00] v1.0.2.7 -> v1.0.2.7
[00479477][19 00][00] v1.0.8.96 -> v1.0.8.96
[00479517][01 00][00] v1.22.4095 -> v1.22.4095
[00479559][01 01][00] v1.22.4095 -> v1.22.4095
[00479617][09 00][05] v2.13.0.0 -> v2.13.0.0
[00479654]Packet upgrade finish successfully.



[00012028]========== 2016.02.03 10:11:35. boot(15) ============
[00012063]Packet [C:\P3S_FW_V01.06.0040.bin] detected, card sn [0x016203e1].
[00012102]Packet upgrade start...

[00012143]Packet checking...
[00012187]Packet vlink 01.06.0040 <-> 01.05.0030.
[00012223]Record vlink 01.06.0040 <-> 01.05.0030 (flow = 0).
[00012262]Done.

[00012299]Version checking[1]...
[00012388][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012451][03 06][00] v2.4.10.7 -> v2.4.10.7
[00012502][04 00][00] v1.41.0.0 -> v1.41.0.0
[00012708][11 00][00] v1.7.15.1 -> v1.7.15.1
[00012796][12 00][00] v1.10.0.0 -> v1.10.0.0
[00012876][12 01][00] v1.10.0.0 -> v1.10.0.0
[00012975][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013178][12 03][00] v1.10.0.0 -> v1.10.0.0
[00013221][15 00][00] v1.1.2.0 -> v1.1.2.0
[00013295][17 00][00] v1.1.1.7 -> v1.1.1.7
[00013411][17 01][00] v1.0.2.7 -> v1.0.2.7
[00013476][19 00][00] v1.0.8.96 -> v1.0.8.96
[00013515][01 00][00] v1.22.4095 -> v1.22.4095
[00013556][01 01][00] v1.22.4095 -> v1.22.4095
[00013616][09 00][00] v2.13.0.0 -> v2.13.0.0
[00013656]Packet upgrade cancelled at version checking.



[00012016]========== 2016.02.03 10:16:21. boot(15) ============
[00012051]Packet [C:\P3S_FW_V01.06.0040.bin] detected, card sn [0x016203e1].
[00012088]Packet upgrade start...

[00012126]Packet checking...
[00012163]Packet vlink 01.06.0040 <-> 01.05.0030.
[00012199]Record vlink 01.06.0040 <-> 01.05.0030 (flow = 0).
[00012234]Done.

[00012270]Version checking[1]...
[00012345][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012405][03 06][00] v2.4.10.7 -> v2.4.10.7
[00012447][04 00][00] v1.41.0.0 -> v1.41.0.0
[00012705][11 00][00] v1.7.15.1 -> v1.7.15.1
[00012793][12 00][00] v1.10.0.0 -> v1.10.0.0
[00012886][12 01][00] v1.10.0.0 -> v1.10.0.0
[00012959][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013034][12 03][00] v1.10.0.0 -> v1.10.0.0
[00013072][15 00][00] v1.1.2.0 -> v1.1.2.0
[00013153][17 00][00] v1.1.1.7 -> v1.1.1.7
[00013279][17 01][00] v1.0.2.7 -> v1.0.2.7
[00013333][19 00][00] v1.0.8.96 -> v1.0.8.96
[00013369][01 00][00] v1.22.4095 -> v1.22.4095
[00013405][01 01][00] v1.22.4095 -> v1.22.4095
[00013453][09 00][00] v2.13.0.0 -> v2.13.0.0
[00013489]Packet upgrade cancelled at version checking.



[00012035]========== 2016.02.03 10:27:19. boot(15) ============
[00012075]Packet [C:\P3S_FW_V01.06.0040.bin] detected, card sn [0x016203e1].
[00012113]Packet upgrade start...

[00012156]Packet checking...
[00012200]Packet vlink 01.06.0040 <-> 01.05.0030.
[00012241]Record vlink 01.06.0040 <-> 01.05.0030 (flow = 0).
[00012278]Done.

[00012318]Version checking[1]...
[00012402][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012583][03 06][00] v2.4.10.7 -> v2.4.10.7
[00012632][04 00][00] v1.41.0.0 -> v1.41.0.0
[00012743][11 00][00] v1.7.0.0 -> v1.7.15.1 need upgrade.
[00012833][12 00][00] v1.10.0.0 -> v1.10.0.0
[00012925][12 01][00] v1.10.0.0 -> v1.10.0.0
[00012994][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013071][12 03][00] v1.10.0.0 -> v1.10.0.0
[00012028]========== 2016.02.03 10:28:16. boot(15) ============
[00012067]Packet [C:\P3S_FW_V01.06.0040.bin] detected, card sn [0x016203e1].
[00012102]Packet upgrade start...

[00012142]Packet checking...
[00012180]Packet vlink 01.06.0040 <-> 01.05.0030.
[00012217]Record vlink 01.06.0040 <-> 01.05.0030 (flow = 0).
[00012254]Done.

[00012291]Version checking[1]...
[00012369][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012450][03 06][00] v2.4.10.7 -> v2.4.10.7
[00012494][04 00][00] v1.41.0.0 -> v1.41.0.0
[00012708][11 00][00] v1.7.0.0 -> v1.7.15.1 need upgrade.
[00012794][12 00][00] v1.10.0.0 -> v1.10.0.0
[00012888][12 01][00] v1.10.0.0 -> v1.10.0.0
[00012988][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013088][12 03][00] v1.10.0.0 -> v1.10.0.0
[00013128][15 00][00] v1.1.2.0 -> v1.1.2.0
[00013213][17 00][00] v1.1.1.7 -> v1.1.1.7
[00013334][17 01][00] v1.0.2.7 -> v1.0.2.7
[00013392][19 00][00] v1.0.8.96 -> v1.0.8.96
[00013430][01 00][00] v1.22.4095 -> v1.22.4095
[00013467][01 01][00] v1.22.4095 -> v1.22.4095
[00013513][09 00][00] v2.13.0.0 -> v2.13.0.0
[00013550]Done.

[00015587]Waiting for user confirm...
[00025623]Timeout, start upgrade automatically.

[00025698]Firmware upgrading[1]...
[00025747][11 00] Firmware upgrade start...
[00071845][11 00] Firmware upgrade finished successfully.
[00071883]Done.

[00071920]Version checking[2]...
[00072013][03 05][00] v34.2.0.9 -> v34.2.0.9
[00072088][03 06][00] v2.4.10.7 -> v2.4.10.7
[00072140][04 00][00] v1.41.0.0 -> v1.41.0.0
[00072249][11 00][05] v1.7.15.1 -> v1.7.15.1
[00072342][12 00][00] v1.10.0.0 -> v1.10.0.0
[00072441][12 01][00] v1.10.0.0 -> v1.10.0.0
[00072521][12 02][00] v1.10.0.0 -> v1.10.0.0
[00072721][12 03][00] v1.10.0.0 -> v1.10.0.0
[00072763][15 00][00] v1.1.2.0 -> v1.1.2.0
[00072857][17 00][00] v1.1.1.7 -> v1.1.1.7
[00072978][17 01][00] v1.0.2.7 -> v1.0.2.7
[00073028][19 00][00] v1.0.8.96 -> v1.0.8.96
[00073083][01 00][00] v1.22.4095 -> v1.22.4095
[00073121][01 01][00] v1.22.4095 -> v1.22.4095
[00073188][09 00][00] v2.13.0.0 -> v2.13.0.0
[00073227]Packet upgrade finish successfully.



[00012018]========== 2016.02.03 10:30:17. boot(15) ============
[00012055]Packet [C:\P3S_FW_V01.06.0040.bin] detected, card sn [0x016203e1].
[00012094]Packet upgrade start...

[00012135]Packet checking...
[00012174]Packet vlink 01.06.0040 <-> 01.05.0030.
[00012212]Record vlink 01.06.0040 <-> 01.05.0030 (flow = 0).
[00012250]Done.

[00012288]Version checking[1]...
[00012381][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012462][03 06][00] v2.4.10.7 -> v2.4.10.7
[00012506][04 00][00] v1.41.0.0 -> v1.41.0.0
[00012702][11 00][00] v1.7.15.1 -> v1.7.15.1
[00012790][12 00][00] v1.10.0.0 -> v1.10.0.0
[00012890][12 01][00] v1.10.0.0 -> v1.10.0.0
[00012990][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013090][12 03][00] v1.10.0.0 -> v1.10.0.0
[00035628][15 00][00] device not detected.
[00035708][17 00][00] v1.1.1.7 -> v1.1.1.7
[00035851][17 01][00] v1.0.2.7 -> v1.0.2.7
[00035912][19 00][00] v1.0.8.96 -> v1.0.8.96
[00035950][01 00][00] v1.22.4095 -> v1.22.4095
[00035989][01 01][00] v1.22.4095 -> v1.22.4095
[00036057][09 00][00] v2.13.0.0 -> v2.13.0.0
[00036095]Packet upgrade failed at version checking.



[00012056]========== 2016.02.03 10:32:07. boot(15) ============
[00012094]Packet [C:\P3S_FW_V01.06.0040.bin] detected, card sn [0x016203e1].
[00012132]Packet upgrade start...

[00012174]Packet checking...
[00012212]Packet vlink 01.06.0040 <-> 01.05.0030.
[00012251]Record vlink 01.06.0040 <-> 01.05.0030 (flow = 0).
[00012288]Done.

[00012327]Version checking[1]...
[00012396][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012556][03 06][00] v2.4.10.7 -> v2.4.10.7
[00012600][04 00][00] v1.41.0.0 -> v1.41.0.0
[00012717][11 00][00] v1.7.15.1 -> v1.7.15.1
[00012805][12 00][00] v1.10.0.0 -> v1.10.0.0
[00012886][12 01][00] v1.10.0.0 -> v1.10.0.0
[00012970][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013056][12 03][00] v1.10.0.0 -> v1.10.0.0
[00013097][15 00][00] v1.1.2.0 -> v1.1.2.0
[00013180][17 00][00] v1.1.1.7 -> v1.1.1.7
[00013301][17 01][00] v1.0.2.7 -> v1.0.2.7
[00013360][19 00][00] v1.0.8.96 -> v1.0.8.96
[00013399][01 00][00] v1.22.4095 -> v1.22.4095
[00013439][01 01][00] v1.22.4095 -> v1.22.4095
[00013500][09 00][00] v2.13.0.0 -> v2.13.0.0
[00013541]Packet upgrade cancelled at version checking.



[00012045]========== 2016.02.03 10:42:10. boot(15) ============
[00012085]Packet [C:\P3S_FW_V01.06.0040.bin] detected, card sn [0x016203e1].
[00012123]Packet upgrade start...

[00012166]Packet checking...
[00012206]Packet vlink 01.06.0040 <-> 01.05.0030.
[00012246]Record vlink 01.06.0040 <-> 01.05.0030 (flow = 0).
[00012285]Done.

[00012324]Version checking[1]...
[00012407][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012487][03 06][00] v2.4.10.7 -> v2.4.10.7
[00012537][04 00][00] v1.41.0.0 -> v1.41.0.0
[00012727][11 00][00] v1.7.15.1 -> v1.7.15.1
[00012816][12 00][00] v1.10.0.0 -> v1.10.0.0
[00012896][12 01][00] v1.10.0.0 -> v1.10.0.0
[00012971][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013067][12 03][00] v1.10.0.0 -> v1.10.0.0
[00035607][15 00][00] device not detected.
[00035694][17 00][00] v1.1.1.7 -> v1.1.1.7
[00035837][17 01][00] v1.0.2.7 -> v1.0.2.7
[00035898][19 00][00] v1.0.8.96 -> v1.0.8.96
[00035939][01 00][00] v1.22.4095 -> v1.22.4095
[00035978][01 01][00] v1.22.4095 -> v1.22.4095
[00036040][09 00][00] v2.13.0.0 -> v2.13.0.0
[00036080]Packet upgrade failed at version checking.



[00012078]========== 2016.02.03 10:47:34. boot(15) ============
[00012121]Packet [C:\P3S_FW_V01.06.0040.bin] detected, card sn [0x016203e1].
[00012163]Packet upgrade start...

[00012335]Packet checking...
[00012381]Packet vlink 01.06.0040 <-> 01.05.0030.
[00012427]Record vlink 01.06.0040 <-> 01.05.0030 (flow = 0).
[00012468]Done.

[00012518]Version checking[1]...
[00012621][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012705][03 06][00] v2.4.10.7 -> v2.4.10.7
[00012770][04 00][00] v1.41.0.0 -> v1.41.0.0
[00012905][11 00][00] v1.7.15.1 -> v1.7.15.1
[00013010][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013109][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013211][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013295][12 03][00] v1.10.0.0 -> v1.10.0.0
[00013343][15 00][00] v1.1.2.0 -> v1.1.2.0
[00013429][17 00][00] v1.1.1.7 -> v1.1.1.7
[00013586][17 01][00] v1.0.2.7 -> v1.0.2.7
[00013655][19 00][00] v1.0.8.96 -> v1.0.8.96
[00013698][01 00][00] v1.22.4095 -> v1.22.4095
[00013745][01 01][00] v1.22.4095 -> v1.22.4095
[00013814][09 00][00] v2.13.0.0 -> v2.13.0.0
[00013859]Packet upgrade cancelled at version checking.



[00012560]========== 2016.02.03 12:17:46. boot(15) ============
[00012621]Packet [C:\P3S_FW_V01.06.0040.bin] detected, card sn [0x016203e1].
[00012669]Packet upgrade start...

[00012713]Packet checking...
[00012759]Packet vlink 01.06.0040 <-> 01.05.0030.
[00012803]Record vlink 01.06.0040 <-> 01.05.0030 (flow = 0).
[00012855]Done.

[00012898]Version checking[1]...
[00012990][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013069][03 06][00] v2.4.10.7 -> v2.4.10.7
[00013152][04 00][00] v1.41.0.0 -> v1.41.0.0
[00013269][11 00][00] v1.7.15.1 -> v1.7.15.1
[00013393][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013472][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013558][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013633][12 03][00] v1.10.0.0 -> v1.10.0.0
[00036177][15 00][00] device not detected.
[00036271][17 00][00] v1.1.1.7 -> v1.1.1.7
[00036403][17 01][00] v1.0.2.7 -> v1.0.2.7
[00036459][19 00][00] v1.0.8.96 -> v1.0.8.96
[00036508][01 00][00] v1.22.4095 -> v1.22.4095
[00036550][01 01][00] v1.22.4095 -> v1.22.4095
[00036643][09 00][00] v2.13.0.0 -> v2.13.0.0
[00036826]Packet upgrade failed at version checking.



[00012594]========== 2016.02.03 12:18:45. boot(0) ============
[00012638]Packet [C:\P3S_FW_V01.06.0040.bin] detected, card sn [0x016203e1].
[00012691]Packet upgrade start...

[00012739]Packet checking...
[00012786]Packet vlink 01.06.0040 <-> 01.05.0030.
[00012835]Record vlink 01.06.0040 <-> 01.05.0030 (flow = 0).
[00012879]Done.

[00012961]Version checking[1]...
[00013052][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013125][03 06][00] v2.4.10.7 -> v2.4.10.7
[00013218][04 00][00] v1.41.0.0 -> v1.41.0.0
[00013324][11 00][00] v1.7.15.1 -> v1.7.15.1
[00013424][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013524][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013624][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013724][12 03][00] v1.10.0.0 -> v1.10.0.0
[00012581]========== 2016.02.03 12:19:42. boot(15) ============
[00012621]Packet [C:\P3S_FW_V01.06.0040.bin] detected, card sn [0x016203e1].
[00012664]Packet upgrade start...

[00012708]Packet checking...
[00012786]Packet vlink 01.06.0040 <-> 01.05.0030.
[00012828]Record vlink 01.06.0040 <-> 01.05.0030 (flow = 0).
[00012870]Done.

[00012911]Version checking[1]...
[00012991][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013072][03 06][00] v2.4.10.7 -> v2.4.10.7
[00013119][04 00][00] v1.41.0.0 -> v1.41.0.0
[00013234][11 00][00] v1.7.15.1 -> v1.7.15.1
[00013319][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013421][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013545][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013680][12 03][00] v1.10.0.0 -> v1.10.0.0
[00036222][15 00][00] device not detected.
[00036302][17 00][00] v1.1.1.7 -> v1.1.1.7
[00036432][17 01][00] v1.0.2.7 -> v1.0.2.7
[00036497][19 00][00] v1.0.8.96 -> v1.0.8.96
[00036540][01 00][00] v1.22.4095 -> v1.22.4095
[00036581][01 01][00] v1.22.4095 -> v1.22.4095
[00036637][09 00][00] v2.13.0.0 -> v2.13.0.0
[00036679]Packet upgrade failed at version checking.



[00013057]========== remo-con disconnect. boot(15) ============
[00013218]Packet [C:\P3S_FW_V01.07.0060.bin] detected, card sn [0x016203e1].
[00013268]Packet upgrade start...

[00013321]Packet checking...
[00013368]Packet vlink 01.07.0060 <-> 01.06.0040.
[00013417]Record vlink 01.06.0040 <-> 01.05.0030 (flow = 0).
[00013466]Done.

[00013514]Version checking[1]...
[00013597][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013697][03 06][00] v2.4.10.7 -> v2.4.13.0 need upgrade.
[00013752][04 00][00] v1.41.0.0 -> v1.41.0.0
[00013897][11 00][00] v1.7.15.1 -> v1.7.15.1
[00014011][12 00][00] v1.10.0.0 -> v1.10.0.0
[00014111][12 01][00] v1.10.0.0 -> v1.10.0.0
[00014217][12 02][00] v1.10.0.0 -> v1.10.0.0
[00014326][12 03][00] v1.10.0.0 -> v1.10.0.0
[00014377][15 00][00] v1.1.2.0 -> v1.1.2.0
[00014466][17 00][00] v1.1.1.7 -> v1.1.1.7
[00014586][17 01][00] v1.0.2.7 -> v1.0.2.7
[00014672][19 00][00] v1.0.8.96 -> v1.0.8.96
[00014720][01 00][00] v1.22.4095 -> v1.23.4920 need upgrade
[00014768][01 01][00] v1.22.4095 -> v1.23.4920 need upgrade
[00014832][09 00][00] v2.13.0.0 -> v2.13.0.0
[00014902]Done.

[00016954]Waiting for user confirm...
[00027002]Timeout, start upgrade automatically.

[00027102]Firmware upgrading[1]...
[00039952][01 00] Firmware upgrade start...
[00011727][01 00] Firmware upgrade finished successfully.
[00011787]Done.

[00011837]Packet [C:\P3S_FW_V01.07.0060.bin] resumed, card sn [0x016203e1].
[00011891]Packet vlink 01.07.0060 <-> 01.06.0040.
[00011953]Record vlink 01.06.0040 <-> 01.05.0030 (flow = 0).
[00012004]Version checking[2]...
[00012080][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012160][03 06][00] v2.4.10.7 -> v2.4.13.0 need upgrade.
[00012217][04 00][00] v1.41.0.0 -> v1.41.0.0
[00012345][11 00][00] v1.7.15.1 -> v1.7.15.1
[00012430][12 00][00] v1.10.0.0 -> v1.10.0.0
[00012520][12 01][00] v1.10.0.0 -> v1.10.0.0
[00012626][12 02][00] v1.10.0.0 -> v1.10.0.0
[00012720][12 03][00] v1.10.0.0 -> v1.10.0.0
[00035270][15 00][00] device not detected.
[00035370][17 00][00] v1.1.1.7 -> v1.1.1.7
[00035510][17 01][00] v1.0.2.7 -> v1.0.2.7
[00035716][19 00][00] v1.0.8.96 -> v1.0.8.96
[00035774][01 00][05] v1.23.4920 -> v1.23.4920
[00035825][01 01][00] v1.22.4095 -> v1.23.4920 need upgrade
[00035915][09 00][00] v2.13.0.0 -> v2.13.0.0
[00035982]Done.

[00036036]Firmware upgrading[2]...
[00036206][01 01] Firmware upgrade start...
[00066541][01 01] Firmware upgrade finished successfully.
[00066809][03 06] Firmware upgrade start...
[00338448][03 06] Firmware upgrade finished successfully.
[00338506]Done.

[00338559]Version checking[3]...
[00338650][03 05][00] v34.2.0.9 -> v34.2.0.9
[00338731][03 06][05] v2.4.13.0 -> v2.4.13.0
[00338798][04 00][00] v1.41.0.0 -> v1.41.0.0
[00338931][11 00][00] v1.7.15.1 -> v1.7.15.1
[00339023][12 00][00] v1.10.0.0 -> v1.10.0.0
[00339123][12 01][00] v1.10.0.0 -> v1.10.0.0
[00339224][12 02][00] v1.10.0.0 -> v1.10.0.0
[00339324][12 03][00] v1.10.0.0 -> v1.10.0.0
[00361879][15 00][00] device not detected.
[00361979][17 00][00] v1.1.1.7 -> v1.1.1.7
[00362131][17 01][00] v1.0.2.7 -> v1.0.2.7
[00362195][19 00][00] v1.0.8.96 -> v1.0.8.96
[00362248][01 00][05] v1.23.4920 -> v1.23.4920
[00362307][01 01][05] v1.23.4920 -> v1.23.4920
[00362396][09 00][00] v2.13.0.0 -> v2.13.0.0
[00362447]Packet upgrade failed at version checking.



[00012086]========== remo-con disconnect. boot(15) ============
[00012139]Packet [C:\P3S_FW_V01.07.0060.bin] detected, card sn [0x016203e1].
[00012193]Packet upgrade start...

[00012254]Packet checking...
[00012304]Packet vlink 01.07.0060 <-> 01.06.0040.
[00012362]Record vlink 01.06.0040 <-> 01.05.0030 (flow = 0).
[00012419]Done.

[00012469]Version checking[1]...
[00012564][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012664][03 06][00] v2.4.13.0 -> v2.4.13.0
[00012721][04 00][00] v1.41.0.0 -> v1.41.0.0
[00012864][11 00][00] v1.7.15.1 -> v1.7.15.1
[00012973][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013073][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013193][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013293][12 03][00] v1.10.0.0 -> v1.10.0.0
[00035943][15 00][00] device not detected.
[00036030][17 00][00] v1.1.1.7 -> v1.1.1.7
[00036172][17 01][00] v1.0.2.7 -> v1.0.2.7
[00036249][19 00][00] v1.0.8.96 -> v1.0.8.96
[00036308][01 00][00] v1.23.4920 -> v1.23.4920
[00036364][01 01][00] v1.23.4920 -> v1.23.4920
[00036429][09 00][00] v2.13.0.0 -> v2.13.0.0
[00036488]Packet upgrade failed at version checking.



[00012872]========== remo-con disconnect. boot(15) ============
[00012927]Packet [C:\P3S_FW_V01.07.0060.bin] detected, card sn [0x016203e1].
[00012985]Packet upgrade start...

[00013037]Packet checking...
[00013094]Packet vlink 01.07.0060 <-> 01.06.0040.
[00013158]Record vlink 01.06.0040 <-> 01.05.0030 (flow = 0).
[00013211]Done.

[00013263]Version checking[1]...
[00013357][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013438][03 06][00] v2.4.13.0 -> v2.4.13.0
[00013500][04 00][00] v1.41.0.0 -> v1.41.0.0
[00013638][11 00][00] v1.7.15.1 -> v1.7.15.1
[00013731][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013832][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013932][12 02][00] v1.10.0.0 -> v1.10.0.0
[00014032][12 03][00] v1.10.0.0 -> v1.10.0.0
[00036592][15 00][00] device not detected.
[00036688][17 00][00] v1.1.1.7 -> v1.1.1.7
[00036829][17 01][00] v1.0.2.7 -> v1.0.2.7
[00036908][19 00][00] v1.0.8.96 -> v1.0.8.96
[00036961][01 00][00] v1.23.4920 -> v1.23.4920
[00037020][01 01][00] v1.23.4920 -> v1.23.4920
[00037088][09 00][00] v2.13.0.0 -> v2.13.0.0
[00037145]Packet upgrade failed at version checking.



[00012558]========== remo-con disconnect. boot(15) ============
[00012610]Packet [C:\P3S_FW_V01.07.0060.bin] detected, card sn [0x016203e1].
[00012661]Packet upgrade start...

[00012715]Packet checking...
[00012768]Packet vlink 01.07.0060 <-> 01.06.0040.
[00012818]Record vlink 01.06.0040 <-> 01.05.0030 (flow = 0).
[00012870]Done.

[00012921]Version checking[1]...
[00013025][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013119][03 06][00] v2.4.13.0 -> v2.4.13.0
[00013301][04 00][00] v1.41.0.0 -> v1.41.0.0
[00013419][11 00][00] v1.7.15.1 -> v1.7.15.1
[00013528][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013628][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013728][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013834][12 03][00] v1.10.0.0 -> v1.10.0.0
[00036389][15 00][00] device not detected.
[00036490][17 00][00] v1.1.1.7 -> v1.1.1.7
[00036642][17 01][00] v1.0.2.7 -> v1.0.2.7
[00036705][19 00][00] v1.0.8.96 -> v1.0.8.96
[00036763][01 00][00] v1.23.4920 -> v1.23.4920
[00036814][01 01][00] v1.23.4920 -> v1.23.4920
[00036886][09 00][00] v2.13.0.0 -> v2.13.0.0
[00036940]Packet upgrade failed at version checking.



[00012669]========== remo-con disconnect. boot(15) ============
[00012723]Packet [C:\P3S_FW_V01.07.0060.bin] detected, card sn [0x016203e1].
[00012773]Packet upgrade start...

[00012828]Packet checking...
[00012883]Packet vlink 01.07.0060 <-> 01.06.0040.
[00012937]Record vlink 01.06.0040 <-> 01.05.0030 (flow = 0).
[00012987]Done.

[00013039]Version checking[1]...
[00013128][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013226][03 06][00] v2.4.13.0 -> v2.4.13.0
[00013284][04 00][00] v1.41.0.0 -> v1.41.0.0
[00013426][11 00][00] v1.7.15.1 -> v1.7.15.1
[00013547][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013649][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013749][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013849][12 03][00] v1.10.0.0 -> v1.10.0.0
[00036408][15 00][00] device not detected.
[00036511][17 00][00] v1.1.1.7 -> v1.1.1.7
[00036651][17 01][00] v1.0.2.7 -> v1.0.2.7
[00036726][19 00][00] v1.0.8.96 -> v1.0.8.96
[00036778][01 00][00] v1.23.4920 -> v1.23.4920
[00036836][01 01][00] v1.23.4920 -> v1.23.4920
[00036906][09 00][00] v2.13.0.0 -> v2.13.0.0
[00036960]Packet upgrade failed at version checking.



[00012203]========== remo-con disconnect. boot(15) ============
[00012257]Packet [C:\P3S_FW_V01.07.0060.bin] detected, card sn [0x016203e1].
[00012319]Packet upgrade start...

[00012382]Packet checking...
[00012434]Packet vlink 01.07.0060 <-> 01.06.0040.
[00012600]Record vlink 01.06.0040 <-> 01.05.0030 (flow = 0).
[00012661]Done.

[00012722]Version checking[1]...
[00012817][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012897][03 06][00] v2.4.13.0 -> v2.4.13.0
[00012970][04 00][00] v1.41.0.0 -> v1.41.0.0
[00013097][11 00][00] v1.7.15.1 -> v1.7.15.1
[00013211][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013311][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013411][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013511][12 03][00] v1.10.0.0 -> v1.10.0.0
[00018070][15 00][00] v1.1.2.0 -> v1.1.2.0
[00018186][17 00][00] v1.1.1.7 -> v1.1.1.7
[00018306][17 01][00] v1.0.2.7 -> v1.0.2.7
[00018387][19 00][00] v1.0.8.96 -> v1.0.8.96
[00018440][01 00][00] v1.23.4920 -> v1.23.4920
[00018500][01 01][00] v1.23.4920 -> v1.23.4920
[00018587][09 00][00] v2.13.0.0 -> v2.13.0.0
[00018643]Packet upgrade cancelled at version checking.



[00012189]========== remo-con disconnect. boot(15) ============
[00012252]Packet [C:\P3S_FW_V01.07.0060.bin] detected, card sn [0x016203e1].
[00012303]Packet upgrade start...

[00012363]Packet checking...
[00012428]Packet vlink 01.07.0060 <-> 01.06.0040.
[00012484]Record vlink 01.07.0060 <-> 01.06.0040 (flow = 0).
[00012535]Done.

[00012591]Version checking[1]...
[00012688][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012769][03 06][00] v2.4.13.0 -> v2.4.13.0
[00012845][04 00][00] v1.41.0.0 -> v1.41.0.0
[00012968][11 00][00] v1.7.15.1 -> v1.7.15.1
[00013077][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013177][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013277][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013380][12 03][00] v1.10.0.0 -> v1.10.0.0
[00035932][15 00][00] device not detected.
[00036018][17 00][00] v1.1.1.7 -> v1.1.1.7
[00036158][17 01][00] v1.0.2.7 -> v1.0.2.7
[00036238][19 00][00] v1.0.8.96 -> v1.0.8.96
[00036288][01 00][00] v1.23.4920 -> v1.23.4920
[00036344][01 01][00] v1.23.4920 -> v1.23.4920
[00036418][09 00][00] v2.13.0.0 -> v2.13.0.0
[00036476]Packet upgrade failed at version checking.



[00012158]========== remo-con disconnect. boot(15) ============
[00012215]Packet [C:\P3S_FW_V01.07.0060.bin] detected, card sn [0x016203e1].
[00012270]Packet upgrade start...

[00012326]Packet checking...
[00012388]Packet vlink 01.07.0060 <-> 01.06.0040.
[00012451]Record vlink 01.07.0060 <-> 01.06.0040 (flow = 0).
[00012503]Done.

[00012558]Version checking[1]...
[00012646][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012726][03 06][00] v2.4.13.0 -> v2.4.13.0
[00012806][04 00][00] v1.41.0.0 -> v1.41.0.0
[00012926][11 00][00] v1.7.15.1 -> v1.7.15.1
[00013046][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013146][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013249][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013347][12 03][00] v1.10.0.0 -> v1.10.0.0
[00035900][15 00][00] device not detected.
[00036017][17 00][00] v1.1.1.7 -> v1.1.1.7
[00036152][17 01][00] v1.0.2.7 -> v1.0.2.7
[00036216][19 00][00] v1.0.8.96 -> v1.0.8.96
[00036279][01 00][00] v1.23.4920 -> v1.23.4920
[00036340][01 01][00] v1.23.4920 -> v1.23.4920
[00036416][09 00][00] v2.13.0.0 -> v2.13.0.0
[00036477]Packet upgrade failed at version checking.



[00012123]========== remo-con disconnect. boot(15) ============
[00012181]Packet [C:\P3S_FW_V01.06.0040.bin] detected, card sn [0x016203e1].
[00012230]Packet upgrade start...

[00012297]Packet checking...
[00012358]Packet vlink 01.06.0040 <-> 01.05.0030.
[00012418]Record vlink 01.07.0060 <-> 01.06.0040 (flow = 1).
[00012472]Done.

[00012527]Version checking[1]...
[00012616][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012701][03 06][00] v2.4.13.0 -> v2.4.10.7
[00012783][04 00][00] v1.41.0.0 -> v1.41.0.0
[00012901][11 00][00] v1.7.15.1 -> v1.7.15.1
[00013020][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013116][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013216][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013316][12 03][00] v1.10.0.0 -> v1.10.0.0
[00035868][15 00][00] device not detected.
[00035967][17 00][00] v1.1.1.7 -> v1.1.1.7
[00036106][17 01][00] v1.0.2.7 -> v1.0.2.7
[00036309][19 00][00] v1.0.8.96 -> v1.0.8.96
[00036372][01 00][00] v1.23.4920 -> v1.22.4095 need upgrade
[00036423][01 01][00] v1.23.4920 -> v1.22.4095 need upgrade
[00036507][09 00][00] v2.13.0.0 -> v2.13.0.0
[00036568]Done.

[00038625]Waiting for user confirm...
[00048682]Timeout, start upgrade automatically.

[00048802]Firmware upgrading[1]...
[00048987][01 01] Firmware upgrade start...
[00079332][01 01] Firmware upgrade finished successfully.
[00079392]Done.

[00079453]Version checking[2]...
[00079544][03 05][00] v34.2.0.9 -> v34.2.0.9
[00079619][03 06][00] v2.4.13.0 -> v2.4.10.7
[00079689][04 00][00] v1.41.0.0 -> v1.41.0.0
[00079840][11 00][00] v1.7.15.1 -> v1.7.15.1
[00079934][12 00][00] v1.10.0.0 -> v1.10.0.0
[00080029][12 01][00] v1.10.0.0 -> v1.10.0.0
[00080130][12 02][00] v1.10.0.0 -> v1.10.0.0
[00080229][12 03][00] v1.10.0.0 -> v1.10.0.0
[00102791][15 00][00] device not detected.
[00102891][17 00][00] v1.1.1.7 -> v1.1.1.7
[00103034][17 01][00] v1.0.2.7 -> v1.0.2.7
[00103111][19 00][00] v1.0.8.96 -> v1.0.8.96
[00103178][01 00][00] v1.23.4920 -> v1.22.4095 need upgrade
[00103236][01 01][05] v1.22.4095 -> v1.22.4095
[00103310][09 00][00] v2.13.0.0 -> v2.13.0.0
[00103377]Packet upgrade failed at version checking.



[00012322]========== remo-con disconnect. boot(15) ============
[00012380]Packet [C:\P3S_FW_V01.07.0060.bin] detected, card sn [0x016203e1].
[00012435]Packet upgrade start...

[00012504]Packet checking...
[00012564]Packet vlink 01.07.0060 <-> 01.06.0040.
[00012623]Record vlink 01.07.0060 <-> 01.06.0040 (flow = 0).
[00012686]Done.

[00012747]Version checking[1]...
[00012838][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012918][03 06][00] v2.4.13.0 -> v2.4.13.0
[00012999][04 00][00] v1.41.0.0 -> v1.41.0.0
[00013118][11 00][00] v1.7.15.1 -> v1.7.15.1
[00013221][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013322][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013421][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013519][12 03][00] v1.10.0.0 -> v1.10.0.0
[00018199][15 00][00] v1.1.2.0 -> v1.1.2.0
[00018285][17 00][00] v1.1.1.7 -> v1.1.1.7
[00018428][17 01][00] v1.0.2.7 -> v1.0.2.7
[00018507][19 00][00] v1.0.8.96 -> v1.0.8.96
[00018568][01 00][00] v1.23.4920 -> v1.23.4920
[00018628][01 01][00] v1.22.4095 -> v1.23.4920 need upgrade
[00018707][09 00][00] v2.13.0.0 -> v2.13.0.0
[00018769]Done.

[00020833]Waiting for user confirm...
[00030893]Timeout, start upgrade automatically.

[00031021]Firmware upgrading[1]...
[00031203][01 01] Firmware upgrade start...
[00061539][01 01] Firmware upgrade finished successfully.
[00061601]Done.

[00061661]Version checking[2]...
[00061762][03 05][00] v34.2.0.9 -> v34.2.0.9
[00061842][03 06][00] v2.4.13.0 -> v2.4.13.0
[00061913][04 00][00] v1.41.0.0 -> v1.41.0.0
[00062082][11 00][00] v1.7.15.1 -> v1.7.15.1
[00062191][12 00][00] v1.10.0.0 -> v1.10.0.0
[00062290][12 01][00] v1.10.0.0 -> v1.10.0.0
[00062390][12 02][00] v1.10.0.0 -> v1.10.0.0
[00062491][12 03][00] v1.10.0.0 -> v1.10.0.0
[00062563][15 00][00] v1.1.2.0 -> v1.1.2.0
[00062644][17 00][00] v1.1.1.7 -> v1.1.1.7
[00062784][17 01][00] v1.0.2.7 -> v1.0.2.7
[00062870][19 00][00] v1.0.8.96 -> v1.0.8.96
[00062935][01 00][00] v1.23.4920 -> v1.23.4920
[00062991][01 01][05] v1.23.4920 -> v1.23.4920
[00063070][09 00][00] v2.13.0.0 -> v2.13.0.0
[00063135]Packet upgrade finish successfully.



[00012184]========== remo-con disconnect. boot(15) ============
[00012237]Packet [C:\P3S_FW_V01.07.0060.bin] detected, card sn [0x0014db2f].
[00012293]Packet upgrade start...

[00012352]Packet checking...
[00012404]Packet vlink 01.07.0060 <-> 01.06.0040.
[00012461]Record vlink 01.07.0060 <-> 01.06.0040 (flow = 0).
[00012515]Done.

[00012568]Version checking[1]...
[00012665][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012745][03 06][00] v2.4.13.0 -> v2.4.13.0
[00012804][04 00][00] v1.41.0.0 -> v1.41.0.0
[00012925][11 00][00] v1.7.15.1 -> v1.7.15.1
[00013045][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013259][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013359][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013459][12 03][00] v1.10.0.0 -> v1.10.0.0
[00036015][15 00][00] device not detected.
[00036115][17 00][00] v1.1.1.7 -> v1.1.1.7
[00036261][17 01][00] v1.0.2.7 -> v1.0.2.7
[00036335][19 00][00] v1.0.8.96 -> v1.0.8.96
[00036386][01 00][00] v1.23.4920 -> v1.23.4920
[00036444][01 01][00] v1.23.4920 -> v1.23.4920
[00036515][09 00][00] v2.13.0.0 -> v2.13.0.0
[00036575]Packet upgrade failed at version checking.



[00012751]========== remo-con disconnect. boot(15) ============
[00012805]Packet [C:\P3S_FW_V01.07.0060.bin] detected, card sn [0x016203e1].
[00012871]Packet upgrade start...

[00012937]Packet checking...
[00013000]Packet vlink 01.07.0060 <-> 01.06.0040.
[00013067]Record vlink 01.07.0060 <-> 01.06.0040 (flow = 0).
[00013130]Done.

[00013196]Version checking[1]...
[00013283][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013399][03 06][00] v2.4.13.0 -> v2.4.13.0
[00013467][04 00][00] v1.41.0.0 -> v1.41.0.0
[00013620][11 00][00] v1.7.15.1 -> v1.7.15.1
[00013708][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013808][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013908][12 02][00] v1.10.0.0 -> v1.10.0.0
[00014008][12 03][00] v1.10.0.0 -> v1.10.0.0
[00036574][15 00][00] device not detected.
[00036669][17 00][00] v1.1.1.7 -> v1.1.1.7
[00036829][17 01][00] v1.0.2.7 -> v1.0.2.7
[00036909][19 00][00] v1.0.8.96 -> v1.0.8.96
[00036966][01 00][00] v1.23.4920 -> v1.23.4920
[00037025][01 01][00] v1.23.4920 -> v1.23.4920
[00037109][09 00][00] v2.13.0.0 -> v2.13.0.0
[00037166]Packet upgrade failed at version checking.



[00012901]========== remo-con disconnect. boot(15) ============
[00012967]Packet [C:\P3S_FW_V01.07.0060.bin] detected, card sn [0x016203e1].
[00013034]Packet upgrade start...

[00013101]Packet checking...
[00013167]Packet vlink 01.07.0060 <-> 01.06.0040.
[00013236]Record vlink 01.07.0060 <-> 01.06.0040 (flow = 0).
[00013298]Done.

[00013489]Version checking[1]...
[00013592][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013692][03 06][00] v2.4.13.0 -> v2.4.13.0
[00013769][04 00][00] v1.41.0.0 -> v1.41.0.0
[00013913][11 00][00] v1.7.15.1 -> v1.7.15.1
[00014026][12 00][00] v1.10.0.0 -> v1.10.0.0
[00014126][12 01][00] v1.10.0.0 -> v1.10.0.0
[00014252][12 02][00] v1.10.0.0 -> v1.10.0.0
[00014357][12 03][00] v1.10.0.0 -> v1.10.0.0
[00018927][15 00][00] v1.1.2.0 -> v1.1.2.0
[00019028][17 00][00] v1.1.1.7 -> v1.1.1.7
[00019161][17 01][00] v1.0.2.7 -> v1.0.2.7
[00019241][19 00][00] v1.0.8.96 -> v1.0.8.96
[00019304][01 00][00] v1.23.4920 -> v1.23.4920
[00019377][01 01][00] v1.23.4920 -> v1.23.4920
[00019461][09 00][00] v2.13.0.0 -> v2.13.0.0
[00019532]Packet upgrade cancelled at version checking.



[00012772]========== remo-con disconnect. boot(15) ============
[00012832]Packet [C:\P3S_FW_V01.06.0040.bin] detected, card sn [0x016203e1].
[00012901]Packet upgrade start...

[00012970]Packet checking...
[00013039]Packet vlink 01.06.0040 <-> 01.05.0030.
[00013100]Record vlink 01.07.0060 <-> 01.06.0040 (flow = 1).
[00013166]Done.

[00013234]Version checking[1]...
[00013340][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013441][03 06][00] v2.4.13.0 -> v2.4.10.7
[00013517][04 00][00] v1.41.0.0 -> v1.41.0.0
[00013659][11 00][00] v1.7.15.1 -> v1.7.15.1
[00013788][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013921][12 01][00] v1.10.0.0 -> v1.10.0.0
[00014023][12 02][00] v1.10.0.0 -> v1.10.0.0
[00014123][12 03][00] v1.10.0.0 -> v1.10.0.0
[00036707][15 00][00] device not detected.
[00036825][17 00][00] v1.1.1.7 -> v1.1.1.7
[00036984][17 01][00] v1.0.2.7 -> v1.0.2.7
[00037080][19 00][00] v1.0.8.96 -> v1.0.8.96
[00037147][01 00][00] v1.23.4920 -> v1.22.4095 need upgrade
[00037215][01 01][00] v1.23.4920 -> v1.22.4095 need upgrade
[00037303][09 00][00] v2.13.0.0 -> v2.13.0.0
[00037363]Done.

[00039427]Waiting for user confirm...
[00049490]Timeout, start upgrade automatically.

[00049628]Firmware upgrading[1]...
[00049941][01 01] Firmware upgrade start...
[00080287][01 01] Firmware upgrade finished successfully.
[00080354]Done.

[00080425]Version checking[2]...
[00080525][03 05][00] v34.2.0.9 -> v34.2.0.9
[00080646][03 06][00] v2.4.13.0 -> v2.4.10.7
[00080713][04 00][00] v1.41.0.0 -> v1.41.0.0
[00080865][11 00][00] v1.7.15.1 -> v1.7.15.1
[00080987][12 00][00] v1.10.0.0 -> v1.10.0.0
[00081113][12 01][00] v1.10.0.0 -> v1.10.0.0
[00081233][12 02][00] v1.10.0.0 -> v1.10.0.0
[00081364][12 03][00] v1.10.0.0 -> v1.10.0.0
[00103941][15 00][00] device not detected.
[00104049][17 00][00] v1.1.1.7 -> v1.1.1.7
[00104214][17 01][00] v1.0.2.7 -> v1.0.2.7
[00104304][19 00][00] v1.0.8.96 -> v1.0.8.96
[00104366][01 00][00] v1.23.4920 -> v1.22.4095 need upgrade
[00104430][01 01][05] v1.22.4095 -> v1.22.4095
[00104510][09 00][00] v2.13.0.0 -> v2.13.0.0
[00104578]Packet upgrade failed at version checking.



[00012808]========== remo-con disconnect. boot(15) ============
[00012878]Packet [C:\P3S_FW_V01.06.0040.bin] detected, card sn [0x016203e1].
[00012939]Packet upgrade start...

[00013005]Packet checking...
[00013074]Packet vlink 01.06.0040 <-> 01.05.0030.
[00013138]Record vlink 01.07.0060 <-> 01.06.0040 (flow = 1).
[00013206]Done.

[00013268]Version checking[1]...
[00013391][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013491][03 06][00] v2.4.13.0 -> v2.4.10.7
[00013575][04 00][00] v1.41.0.0 -> v1.41.0.0
[00013713][11 00][00] v1.7.15.1 -> v1.7.15.1
[00013825][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013940][12 01][00] v1.10.0.0 -> v1.10.0.0
[00014036][12 02][00] v1.10.0.0 -> v1.10.0.0
[00014140][12 03][00] v1.10.0.0 -> v1.10.0.0
[00018709][15 00][00] v1.1.2.0 -> v1.1.2.0
[00018818][17 00][00] v1.1.1.7 -> v1.1.1.7
[00018957][17 01][00] v1.0.2.7 -> v1.0.2.7
[00019055][19 00][00] v1.0.8.96 -> v1.0.8.96
[00019122][01 00][00] v1.23.4920 -> v1.22.4095 need upgrade
[00019190][01 01][00] v1.22.4095 -> v1.22.4095
[00019277][09 00][00] v2.13.0.0 -> v2.13.0.0
[00019452]Done.

[00021511]Waiting for user confirm...
[00031582]Timeout, start upgrade automatically.

[00031731]Firmware upgrading[1]...
[00046238][01 00] Firmware upgrade start...
[00011938][01 00] Firmware upgrade finished successfully.
[00012011]Done.

[00012079]Packet [C:\P3S_FW_V01.06.0040.bin] resumed, card sn [0x016203e1].
[00012154]Packet vlink 01.06.0040 <-> 01.05.0030.
[00012223]Record vlink 01.07.0060 <-> 01.06.0040 (flow = 1).
[00012289]Version checking[2]...
[00012405][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012505][03 06][00] v2.4.13.0 -> v2.4.10.7
[00012584][04 00][00] v1.41.0.0 -> v1.41.0.0
[00012725][11 00][00] v1.7.15.1 -> v1.7.15.1
[00012839][12 00][00] v1.10.0.0 -> v1.10.0.0
[00012966][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013095][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013220][12 03][00] v1.10.0.0 -> v1.10.0.0
[00035788][15 00][00] device not detected.
[00035893][17 00][00] v1.1.1.7 -> v1.1.1.7
[00036051][17 01][00] v1.0.2.7 -> v1.0.2.7
[00036152][19 00][00] v1.0.8.96 -> v1.0.8.96
[00036219][01 00][05] v1.22.4095 -> v1.22.4095
[00036282][01 01][00] v1.22.4095 -> v1.22.4095
[00036394][09 00][00] v2.13.0.0 -> v2.13.0.0
[00036453]Packet upgrade failed at version checking.



[00012721]========== remo-con disconnect. boot(15) ============
[00012791]Packet [C:\P3S_FW_V01.07.0060.bin] detected, card sn [0x016203e1].
[00012861]Packet upgrade start...

[00012938]Packet checking...
[00013007]Packet vlink 01.07.0060 <-> 01.06.0040.
[00013073]Record vlink 01.07.0060 <-> 01.06.0040 (flow = 0).
[00013139]Done.

[00013202]Version checking[1]...
[00013313][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013418][03 06][00] v2.4.13.0 -> v2.4.13.0
[00013497][04 00][00] v1.41.0.0 -> v1.41.0.0
[00013633][11 00][00] v1.7.15.1 -> v1.7.15.1
[00013742][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013867][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013993][12 02][00] v1.10.0.0 -> v1.10.0.0
[00014102][12 03][00] v1.10.0.0 -> v1.10.0.0
[00014173][15 00][00] v1.1.2.0 -> v1.1.2.0
[00014419][17 00][00] v1.1.1.7 -> v1.1.1.7
[00014576][17 01][00] v1.0.2.7 -> v1.0.2.7
[00014682][19 00][00] v1.0.8.96 -> v1.0.8.96
[00014754][01 00][00] v1.22.4095 -> v1.23.4920 need upgrade
[00014822][01 01][00] v1.22.4095 -> v1.23.4920 need upgrade
[00014902][09 00][00] v2.13.0.0 -> v2.13.0.0
[00014974]Done.

[00017039]Waiting for user confirm...
[00027116]Timeout, start upgrade automatically.

[00027255]Firmware upgrading[1]...
[00041700][01 00] Firmware upgrade start...
[00012334][01 00] Firmware upgrade finished successfully.
[00012409]Done.

[00012477]Packet [C:\P3S_FW_V01.07.0060.bin] resumed, card sn [0x016203e1].
[00012554]Packet vlink 01.07.0060 <-> 01.06.0040.
[00012626]Record vlink 01.07.0060 <-> 01.06.0040 (flow = 0).
[00012689]Version checking[2]...
[00012799][03 05][00] v34.2.0.9 -> v34.2.0.9
[00012899][03 06][00] v2.4.13.0 -> v2.4.13.0
[00012980][04 00][00] v1.41.0.0 -> v1.41.0.0
[00013122][11 00][00] v1.7.15.1 -> v1.7.15.1
[00013232][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013328][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013452][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013554][12 03][00] v1.10.0.0 -> v1.10.0.0
[00036123][15 00][00] device not detected.
[00036228][17 00][00] v1.1.1.7 -> v1.1.1.7
[00036364][17 01][00] v1.0.2.7 -> v1.0.2.7
[00036449][19 00][00] v1.0.8.96 -> v1.0.8.96
[00036515][01 00][05] v1.23.4920 -> v1.23.4920
[00036589][01 01][00] v1.22.4095 -> v1.23.4920 need upgrade
[00036669][09 00][00] v2.13.0.0 -> v2.13.0.0
[00036744]Done.

[00036812]Firmware upgrading[2]...
[00037004][01 01] Firmware upgrade start...
[00067368][01 01] Firmware upgrade finished successfully.
[00067442]Done.

[00067510]Version checking[3]...
[00067623][03 05][00] v34.2.0.9 -> v34.2.0.9
[00067723][03 06][00] v2.4.13.0 -> v2.4.13.0
[00067799][04 00][00] v1.41.0.0 -> v1.41.0.0
[00067942][11 00][00] v1.7.15.1 -> v1.7.15.1
[00068054][12 00][00] v1.10.0.0 -> v1.10.0.0
[00068176][12 01][00] v1.10.0.0 -> v1.10.0.0
[00068442][12 02][00] v1.10.0.0 -> v1.10.0.0
[00068546][12 03][00] v1.10.0.0 -> v1.10.0.0
[00091125][15 00][00] device not detected.
[00091228][17 00][00] v1.1.1.7 -> v1.1.1.7
[00091377][17 01][00] v1.0.2.7 -> v1.0.2.7
[00091477][19 00][00] v1.0.8.96 -> v1.0.8.96
[00091546][01 00][05] v1.23.4920 -> v1.23.4920
[00091618][01 01][05] v1.23.4920 -> v1.23.4920
[00091713][09 00][00] v2.13.0.0 -> v2.13.0.0
[00091791]Packet upgrade failed at version checking.



[00012829]========== remo-con disconnect. boot(15) ============
[00012901]Packet [C:\P3S_FW_V01.07.0060.bin] detected, card sn [0x016203e1].
[00012972]Packet upgrade start...

[00013050]Packet checking...
[00013123]Packet vlink 01.07.0060 <-> 01.06.0040.
[00013196]Record vlink 01.07.0060 <-> 01.06.0040 (flow = 0).
[00013265]Done.

[00013335]Version checking[1]...
[00013437][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013537][03 06][00] v2.4.13.0 -> v2.4.13.0
[00013612][04 00][00] v1.41.0.0 -> v1.41.0.0
[00013737][11 00][00] v1.7.15.1 -> v1.7.15.1
[00013858][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013960][12 01][00] v1.10.0.0 -> v1.10.0.0
[00014061][12 02][00] v1.10.0.0 -> v1.10.0.0
[00014160][12 03][00] v1.10.0.0 -> v1.10.0.0
[00036735][15 00][00] device not detected.
[00036842][17 00][00] v1.1.1.7 -> v1.1.1.7
[00036982][17 01][00] v1.0.2.7 -> v1.0.2.7
[00037069][19 00][00] v1.0.8.96 -> v1.0.8.96
[00037136][01 00][00] v1.23.4920 -> v1.23.4920
[00037197][01 01][00] v1.23.4920 -> v1.23.4920
[00037287][09 00][00] v2.13.0.0 -> v2.13.0.0
[00037358]Packet upgrade failed at version checking.



[00012430]========== remo-con disconnect. boot(15) ============
[00012496]Packet [C:\P3S_FW_V01.08.0080.bin] detected, card sn [0x016203e1].
[00012567]Packet upgrade start...

[00012639]Packet checking...
[00012712]Packet vlink 01.08.0080 <-> 01.07.0060.
[00012784]Record vlink 01.07.0060 <-> 01.06.0040 (flow = 0).
[00012844]Done.

[00012918]Version checking[1]...
[00013039][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013279][03 06][00] v2.4.13.0 -> v2.4.14.5 need upgrade.
[00013368][04 00][00] v1.41.0.0 -> v1.44.0.0 need upgrade.
[00013502][11 00][00] v1.7.15.1 -> v1.7.15.1
[00013609][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013737][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013860][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013994][12 03][00] v1.10.0.0 -> v1.10.0.0
[00018568][15 00][00] v1.1.2.0 -> v1.1.2.0
[00018685][17 00][00] v1.1.1.7 -> v1.1.1.7
[00018846][17 01][00] v1.0.2.7 -> v1.0.2.7
[00018925][19 00][00] v1.0.8.96 -> v1.0.8.96
[00018999][01 00][00] v1.23.4920 -> v1.23.4920
[00019068][01 01][00] v1.23.4920 -> v1.23.4920
[00019165][09 00][00] v2.13.0.0 -> v3.0.0.10 need upgrade.
[00019234]Done.

[00021308]Waiting for user confirm...
[00031384]Timeout, start upgrade automatically.

[00031531]Firmware upgrading[1]...
[00031803][03 06] Firmware upgrade start...
[00311341][03 06] Firmware upgrade finished successfully.
[00311439][09 00] Firmware upgrade start...
[00363365][09 00] Firmware upgrade finished successfully.
[00363470][04 00] Firmware upgrade start...
[00422325][04 00] Firmware upgrade finished successfully.
[00422405]Done.

[00422474]Version checking[2]...
[00422608][03 05][00] v34.2.0.9 -> v34.2.0.9
[00422732][03 06][05] v2.4.14.5 -> v2.4.14.5
[00422810][04 00][05] v1.44.0.0 -> v1.44.0.0
[00422969][11 00][00] v1.7.15.1 -> v1.7.15.1
[00423101][12 00][00] v1.10.0.0 -> v1.10.0.0
[00423238][12 01][00] v1.10.0.0 -> v1.10.0.0
[00423361][12 02][00] v1.10.0.0 -> v1.10.0.0
[00423497][12 03][00] v1.10.0.0 -> v1.10.0.0
[00423570][15 00][00] v1.1.2.0 -> v1.1.2.0
[00423697][17 00][00] v1.1.1.7 -> v1.1.1.7
[00423860][17 01][00] v1.0.2.7 -> v1.0.2.7
[00423986][19 00][00] v1.0.8.96 -> v1.0.8.96
[00424059][01 00][00] v1.23.4920 -> v1.23.4920
[00424131][01 01][00] v1.23.4920 -> v1.23.4920
[00424226][09 00][05] v3.0.0.10 -> v3.0.0.10
[00424301]Packet upgrade finish successfully.



[00012285]========== remo-con disconnect. boot(15) ============
[00012462]Packet [C:\P3S_FW_V01.08.0080.bin] detected, card sn [0x016203e1].
[00012539]Packet upgrade start...

[00012612]Packet checking...
[00012686]Packet vlink 01.08.0080 <-> 01.07.0060.
[00012756]Record vlink 01.08.0080 <-> 01.07.0060 (flow = 0).
[00012831]Done.

[00012903]Version checking[1]...
[00013014][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013114][03 06][00] v2.4.14.5 -> v2.4.14.5
[00013203][04 00][00] v1.44.0.0 -> v1.44.0.0
[00013354][11 00][00] v1.7.15.1 -> v1.7.15.1
[00013476][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013583][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013713][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013842][12 03][00] v1.10.0.0 -> v1.10.0.0
[00036417][15 00][00] device not detected.
[00036519][17 00][00] v1.1.1.7 -> v1.1.1.7
[00036679][17 01][00] v1.0.2.7 -> v1.0.2.7
[00036784][19 00][00] v1.0.8.96 -> v1.0.8.96
[00036861][01 00][00] v1.23.4920 -> v1.23.4920
[00036935][01 01][00] v1.23.4920 -> v1.23.4920
[00037024][09 00][00] v3.0.0.10 -> v3.0.0.10
[00037094]Packet upgrade failed at version checking.



[00012285]========== remo-con disconnect. boot(15) ============
[00012362]Packet [C:\P3S_FW_V01.08.0080.bin] detected, card sn [0x016203e1].
[00012433]Packet upgrade start...

[00012510]Packet checking...
[00012584]Packet vlink 01.08.0080 <-> 01.07.0060.
[00012651]Record vlink 01.08.0080 <-> 01.07.0060 (flow = 0).
[00012726]Done.

[00012795]Version checking[1]...
[00012902][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013021][03 06][00] v2.4.14.5 -> v2.4.14.5
[00013096][04 00][00] v1.44.0.0 -> v1.44.0.0
[00013246][11 00][00] v1.7.15.1 -> v1.7.15.1
[00013370][12 00][00] v1.10.0.0 -> v1.10.0.0
[00013474][12 01][00] v1.10.0.0 -> v1.10.0.0
[00013601][12 02][00] v1.10.0.0 -> v1.10.0.0
[00013711][12 03][00] v1.10.0.0 -> v1.10.0.0
[00036290][15 00][00] device not detected.
[00036411][17 00][00] v1.1.1.7 -> v1.1.1.7
[00036556][17 01][00] v1.0.2.7 -> v1.0.2.7
[00036651][19 00][00] v1.0.8.96 -> v1.0.8.96
[00036727][01 00][00] v1.23.4920 -> v1.23.4920
[00036919][01 01][00] v1.23.4920 -> v1.23.4920
[00037031][09 00][00] v3.0.0.10 -> v3.0.0.10
[00037104]Packet upgrade failed at version checking.



[00012310]========== remo-con disconnect. boot(15) ============
[00012389]Packet [C:\P3S_FW_V01.08.0080.bin] detected, card sn [0x016203e1].
[00012462]Packet upgrade start...

[00012545]Packet checking...
[00012617]Packet vlink 01.08.0080 <-> 01.07.0060.
[00012689]Record vlink 01.08.0080 <-> 01.07.0060 (flow = 0).
[00012760]Done.

[00012838]Version checking[1]...
[00012942][03 05][00] v34.2.0.9 -> v34.2.0.9
[00015543][03 06][00] v2.4.14.5 -> v2.4.14.5
[00015618][04 00][00] v1.44.0.0 -> v1.44.0.0
[00015762][11 00][00] v1.7.15.1 -> v1.7.15.1
[00015876][12 00][00] v1.10.0.0 -> v1.10.0.0
[00016001][12 01][00] v1.10.0.0 -> v1.10.0.0
[00016137][12 02][00] v1.10.0.0 -> v1.10.0.0
[00016262][12 03][00] v1.10.0.0 -> v1.10.0.0
[00016345][15 00][00] v1.1.2.0 -> v1.1.2.0
[00016448][17 00][00] v1.1.1.7 -> v1.1.1.7
[00016627][17 01][00] v1.0.2.7 -> v1.0.2.7
[00016726][19 00][00] v1.0.8.96 -> v1.0.8.96
[00016798][01 00][00] v1.23.4920 -> v1.23.4920
[00016875][01 01][00] v1.23.4920 -> v1.23.4920
[00016968][09 00][00] v3.0.0.10 -> v3.0.0.10
[00017044]Packet upgrade cancelled at version checking.



[00012865]========== remo-con disconnect. boot(15) ============
[00012944]Packet [C:\P3S_FW_V01.08.0080.bin] detected, card sn [0x016203e1].
[00013017]Packet upgrade start...

[00013096]Packet checking...
[00013165]Packet vlink 01.08.0080 <-> 01.07.0060.
[00013236]Record vlink 01.08.0080 <-> 01.07.0060 (flow = 0).
[00013312]Done.

[00013385]Version checking[1]...
[00013508][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013621][03 06][00] v2.4.14.5 -> v2.4.14.5
[00013698][04 00][00] v1.44.0.0 -> v1.44.0.0
[00013861][11 00][00] v1.7.15.1 -> v1.7.15.1
[00013995][12 00][00] v1.10.0.0 -> v1.10.0.0
[00014123][12 01][00] v1.10.0.0 -> v1.10.0.0
[00014230][12 02][00] v1.10.0.0 -> v1.10.0.0
[00014475][12 03][00] v1.10.0.0 -> v1.10.0.0
[00037055][15 00][00] device not detected.
[00037192][17 00][00] v1.1.1.7 -> v1.1.1.7
[00037351][17 01][00] v1.0.2.7 -> v1.0.2.7
[00037446][19 00][00] v1.0.8.96 -> v1.0.8.96
[00037522][01 00][00] v1.23.4920 -> v1.23.4920
[00037600][01 01][00] v1.23.4920 -> v1.23.4920
[00037692][09 00][00] v3.0.0.10 -> v3.0.0.10
[00037767]Packet upgrade failed at version checking.



[00012977]========== remo-con disconnect. boot(15) ============
[00013059]Packet [C:\P3S_FW_V01.08.0080.bin] detected, card sn [0x016203e1].
[00013133]Packet upgrade start...

[00013212]Packet checking...
[00013287]Packet vlink 01.08.0080 <-> 01.07.0060.
[00013366]Record vlink 01.08.0080 <-> 01.07.0060 (flow = 0).
[00013438]Done.

[00013516]Version checking[1]...
[00013626][03 05][00] v34.2.0.9 -> v34.2.0.9
[00013750][03 06][00] v2.4.14.5 -> v2.4.14.5
[00013842][04 00][00] v1.44.0.0 -> v1.44.0.0
[00013985][11 00][00] v1.7.15.1 -> v1.7.15.1
[00014119][12 00][00] v1.10.0.0 -> v1.10.0.0
[00014254][12 01][00] v1.10.0.0 -> v1.10.0.0
[00014378][12 02][00] v1.10.0.0 -> v1.10.0.0
[00014514][12 03][00] v1.10.0.0 -> v1.10.0.0
[00037096][15 00][00] device not detected.
[00037215][17 00][00] v1.1.1.7 -> v1.1.1.7
[00037375][17 01][00] v1.0.2.7 -> v1.0.2.7
[00037467][19 00][00] v1.0.8.96 -> v1.0.8.96
[00037548][01 00][00] v1.23.4920 -> v1.23.4920
[00037626][01 01][00] v1.23.4920 -> v1.23.4920
[00037726][09 00][00] v3.0.0.10 -> v3.0.0.10
[00037800]Packet upgrade failed at version checking.

aerdt Posted at 2016-4-11 16:16
Thanks Donnie,

tried upgrading with the RC Update v1.6, but the RC (GL300B) won't upgrade. It's b ...

Aerdt can you answer post 15 first please, then we can go from there.
Ok when you bought this , did you register with DJI on the Go app screen.  You would have had the RC hooked up to the Go app and it would have asked you your e mail address and information.  You CANNOT UPDATE ANYTHING UNTIL YOU HAVE DONE SO.   If you did register go to step  2   if not let me know

step 2  .One thing I dont understand is how you can have a green light on your transmitter ?  The update  must be done to both the aircraft and the RC for the system to work.  Are you sure you updated the Aircraft?  Did the  SD card say "Success"  after the install ?  At this point right now, can you still fly the aircraft ? does the system  still work ?   If it does work then one of two things has happened.....  ONE .The Aircraft never was updated and you are still on the previous Firmware or  TWO  The RC Transmitter did update  somehow.    Before we go any further please get back with me on that question......Does the system still work?  if it does NOT  continue  to step 3  If it does stop and let me know .
---




Step 3 : Did you follow my updateing the "bricked Rc tutorial " to the letter ?  It is critical that the Thumb drive be formatted and the only thing on the thumb drive is the Bin file .
Are you using a Mac or a PC.  Avoid the Mac if you can   .
Try another device to get the Go App working.  (That go app will open , even when not connected to anything, make sure you can do this. )

also  I dont think the USB failed on the RC, You were using the USB and the RC to fly before the Update caused the problems correct ?  I just read that you never flew it before ??  You very well may hae a bad usb port.  TRY ANOTHER CABLE FIRST  Make sure from MAIN USB to the I-pad     

So the aircraft is at 1.8 correct ?  I would like you to confirm the current RC on your device by doing this rollback procedure. But not rolling back, this will at least tell  me what version we are on.

follow this vido tutorial on rolling back firmware.  and let me know what it says is the "Current one " installed.  Then just close out of it.  I wonder if you updated and then just lost the link to the aircraft.
https://www.youtube.com/watch?v=3OYajs-xmJ4&feature=youtu.be

sandmark Posted at 2016-4-12 08:18
DJI Ken,
I just tried to reinstall the 1.8.80 to the Bird via the SD card. It failed.
I then got it  ...

I pad should be 2.7.1 not 2.7.2  the .2 version is for Androids ONLY.  Try it with the correct App for the I pad.
Regardless of the above fact your aircraft and transmitter  will have to go in for service. When lines 1500 says "Device Not Detected " for the latest Upload .  Somehow the" Video Transmission Board" has become corrupted this is sometimes  caused by  the Transmitter being on when the aircraft is updating or the SD card was formatted with a MAC with data still on the card ( Not formatted )  I am not saying always, but this is the most common causes that I have seen.




sorry to tell you this - donnie

East Side Kid Posted at 2016-4-12 02:48
I appear to be having the same connection problem, but for a different reason.  I upgraded to the  ...

Yep, I have the EXACT same issue.

Everything seems to be fine, however DJI GO on my iPad mini 2 (iOS 9.3.1) does NOT recognize the RC and will not show the "Connect" button. DJI GO just shows the "How To Connect" button.

The RC shows a green light and can communicate with the Phantom, but only for the camera movement. For the rest, I assume you'll need a connection to the DJI GO app. Looks like some sort of bug with DJI GO, as everything worked perfectly before.

This is a Phantom 3 Advanced (v 1.8.80) with the "B" RC (v ?).

I too am having the same issue with my Samsung Galaxy S6. At first I thought it was my phone because I can use my tablet and everything works fine. But when I try to use my phone, I get the how to connect page. I asked about this issue on facebook and everyone kept telling me to do a factory reset on my phone. I did that. Then spent the next several hours trying to put pictures and everything else back on my phone. Same issue. I can use my tablet to fly but I can not use my Samsung Galaxy S6.
I have been busy and did not fly for about two weeks. But I did not have any problems with using my phone before. This happened before the new update came out. I used my tablet to update firmware on RC and the AC. After update, I still can not use my phone. I thought it was just a problem with the type of phone I am using. But it seems like a lot of people are having the same issue with several other types of devices.
Any suggestions?
Thanks

aerdt Posted at 2016-4-12 11:07
Yep, I have the EXACT same issue.

Everything seems to be fine, however DJI GO on my iPad mini 2 ( ...

When you have the go app on the I pad NOT connected to the RC can you scroll to the left and right
and see the Inspire or the Matrice  or osmo ?  
When you get to the Phantom page, the GO app should at least open and take you to the main screen ? when you get to the main screen go to the top right hand corner and open the General settings and scroll down to the "About " page this will tell you what app is on the I pad.  

Just curious , then we can get back to the task at hand

donnie

weezer58@yahoo. Posted at 2016-4-13 00:55
I too am having the same issue with my Samsung Galaxy S6. At first I thought it was my phone because ...

If your Samsung is updated to Marshmallow, swipe down and open the USB tab and choose USE USB FOR- Software Installation. You may have to do it every time you fly. Also have UBS debugging on and also developer options enabled.

aerdt Posted at 2016-4-13 00:07
Yep, I have the EXACT same issue.

Everything seems to be fine, however DJI GO on my iPad mini 2 ( ...

See my post above if you are using Android.

DJI-Ken Posted at 2016-4-12 12:24
If your Samsung is updated to Marshmallow, swipe down and open the USB tab and choose USE USB FOR- ...

My phone is using android version 6.0.1 It does not say anything about marshmallow.

weezer58@yahoo. Posted at 2016-4-13 01:50
My phone is using android version 6.0.1 It does not say anything about marshmallow.

You are on the latest update. Go to the settings and scroll down to developer options and make sure it's on and enable USB debugging.
Then when you power everything up, swipe down from the top and choose USB settings and select. SOFTWARE INSTALLATION. You have have to do the last step every time.

Donnie Posted at 2016-4-12 19:13
When you have the go app on the I pad NOT connected to the RC can you scroll to the left and righ ...

Yes, I can scroll left and right through the different models. When I am on the Phantom page, it just shows the "How to connect" button.

I am currently on a business trip, but back home tomorrow and will report what I can see in the "About" page. It is definitely the latest version, as I reset the iPad and re-installed the app. I am also logged into the app with my DJI account.
I did try to update the RC firmware yesterday with the USB stick (Windows formatted, FAT32, single Fw file in the root - tried both your CW_ file and the full Fw v1.8.80) and the RC wouldn't do anything - just beep after approx. 10 minutes and there's no log file or activity on the stick. The stick is connected though, as I have an activity indicator on the stick.

Then I tried updating the RC by connecting to the drone's usb port. Same result.

Then I tried the C1 C2.. reset...just got a steady cyan light on the RC.

When I power up the RC and the AC, they do bind. RC light is green and I can control the camera with the RC.

The USB port on the iPad is working fine - I can hear the USB connect ding everytime I plug in the cable. The cable is also NOT faulty. It works fine connected with a computer with iTunes.

However, the DJI Go app is dead and won't connect. The only thing I haven't tried is to do a full factory reset of the iPad with iTunes.

what kind of tablet (android or IOS) are you using, I was fortunite to have both. Maybe i'm wrong but it looks like android users are using the most current version of the DJI Go-app (2.7.2) and are not having firmware update problems, yes or no. Android updated its DJI Go app a week before the firmware upgrade. I have not seen any IOS upgrades for the DJI Go app. I own three drones (Inspire 1, Phantom 3 Pro & Phantom 4) all work well with my android (Nvidia Shield) tablet. If I plug in the iPad mini 3 (IOS) I get errors and "firmware upgrade needed".  If you recall about a year ago we had a similar problem with a firmware update and the IOS version of the app. DJI did a update that corrected this issue.

Donnie Posted at 2016-4-12 22:38
I pad should be 2.7.1 not 2.7.2  the .2 version is for Androids ONLY.  Try it with the correct App  ...

Donnie,
I Dont know what version the app is on the iPad as I cant use it.
When it did work it was on version 2.7.1 (and still would be as there is no 2.7.2 on ios)
Bird was 1.7.60
Rc was 1.5.80
Updated Bird to 1.8.80 (success)
Rc to 1.6.0 (success)
And then the iPad wouldn't recognize the app

The Transmitter was not on!!! when the Bird was updated - Read my other posts.
SD card was formatted on a PC.
I get it needs to go in Im just waiting on the place I bought it from to get the approval they sent off for.

Upgrading p3 sucks, P2 was so much better, they should move back toward that method.

Donnie Posted at 2016-4-13 01:13
When you have the go app on the I pad NOT connected to the RC can you scroll to the left and righ ...

Hi Donnie,
On iPad with RC disconnected the app will let me swipe left and right (Inspire , Matrice, Phantom etc)
but when I go to the phantom page it will not open (how to connect) only cant get into the menus to go to (about) to see the firmware versions.

Opened my Sony phone app without connection and I can.
Thanks

aerdt Posted at 2016-4-12 12:07
Yep, I have the EXACT same issue.

Everything seems to be fine, however DJI GO on my iPad mini 2 ( ...

Thanks for the input, aerdt.  I appreciate it.  At least I'm not alone on this.  I do know that DJI is working on the bug, whatever it is.  Hopefully, they'll get it squared away soon.

Dennis

weezer58@yahoo. Posted at 2016-4-12 12:55
I too am having the same issue with my Samsung Galaxy S6. At first I thought it was my phone because ...

Looks like there's a problem, Houston!  Thanks, Weezer58!  Maybe they'll get it worked out soon.

sandmark Posted at 2016-4-12 18:57
Donnie,
I Dont know what version the app is on the iPad as I cant use it.
When it did work it was  ...

Just FYI, on the "connect to..." page when it won't recognize the P-3, I changed to the P-Standard and got the "camera" view.  I could then get into the software, but it didn't do me any good because I couldn't re-set anything...didn't really want to.  Odd.  

Like i posted before this problem is over a months old, i had this problem before and it wasnt solved at all. I sended my remote controller to the DJI service and it should ne here tomorrow. I highly doubt that the remote was the problem. I get the how to connect screen on every IOS device i have and on android

http://forum.dji.com/thread-44739-1-1.html

I am also having all the identical problems.  iPad2 Air, P3A, and good cables.  P3A updated fine, batteries updated fine, remote bricked but acts normal.   Have a green connect light between the two.  The remote doesn't work though, except to activate camera.  It will not connect to DJI GO.  Between work and play I have connected with DJI on the chat several times, its like starting over everytime.  I have sent them the link to this thread but they don't read it, instead they want to start over with troubleshooting.  The last guy wanted me to make a video and post it to YouTube so they could see it.  I haven't had time to post it yet, but did get it filmed.  DJI please help you have a bug that is needing fixed.

aerdt Posted at 2016-4-12 16:30
Yes, I can scroll left and right through the different models. When I am on the Phantom page, it ju ...

Keep in mind one fact.  YOU DO NOT UPDATE THE RC WITH 1.8.80  That is only for the Aircraft .  The version  numbers do not match.   I think that you do not have either the RC or the Aircraft updated at all.  When you get Home, dont do anything until you can look at the About Page with all sytems on .  Then list them here and I will help you.  

Also I want you to delete the Go App off of the Ipad and start over unless you are sure you have version 2.7.1.  This will be confirmed when you get home and list everything on The 'About" page .
Also just to be clear  :   RC= Radio Control =  Also called the  Transmitter some call it Controller                                                              AC = aircraft     FW = firmware  
Make sure you are using the USB full size port on the RC to connect to  I-pad.  Some of the new Phanotm 4 were shipped with the Mini  usb cables, I just want tomake sure you are not using one of those.

Can you try another device to install the GO app on and Make sure the USB port is indeed working ?   I have heard of more than one time of the USB port being BAD and being Brand NEW.  We muyst make sure of this or we are spinning our wheels .  Nothing will load if the USB port is damaged on The RC.  

Also I have heard that apple is coming out with a fix for some of the App problems.  I guess you must delete the latest update 9.3.1 on the Ipad and then re-load it through  I tunes.  I guess the DJI pilots that are having trouble did not update through the I tunes store, they must do it this way to get a clean install.  This may be the whole Problem why you cant open the GO APP.  I would work on this first .  If I get more info I will let you know.  

So four  questions I need when you get back , IN parathesis and in RED  I will list the reason I need these answers >

1- Now forgive me if I missed it, You did upate and register with DJI on the go app correct?     ( If you did not register and  then  begin updating, it will brick the system )

2- Please list  (Aircarft and RC Go app on )   The Versions of FW that you can read on the Go App "About " tab  (  I need to see if any updates have been completed  )

3-  When you have the RC and Aircraft on , Can you start the motors ( dont fly )  ?   ( I need t know if you are still bound to the System , both RC and video)

4-Can you load the go app on a IPhone or other apple device ?  ( we need to be sure the USB is working and that you can open the GO APP . If it works on another device we know the USB port on the RC is good .  If it will still not open , we have defective RC

Sorry for the million questions - donnie

sandmark Posted at 2016-4-12 17:57
Donnie,
I Dont know what version the app is on the iPad as I cant use it.
When it did work it was  ...

The reason I mentiond the cause is because I read this line
Sandmark : " I have the same issues and its been updated correctly! Bird off when doing the RC update"
I  was just giving what can cause ( Loss of Video board )  this along with the Mac's as well  .  I am sorry if I did not see  another area where it said "The Transmitter was not ON when I updated the Aircraft "  I did read the Post, must have missed that part.



I am sorry about the aircraft having to go in.

Donnie

sandmark Posted at 2016-4-12 17:57
Donnie,
I Dont know what version the app is on the iPad as I cant use it.
When it did work it was  ...

The app will open regardless, even if not connected to the RC.  Just tap on the Camera or equipment button , it will open . then go to General settings in the Top right hand corner and open that Go to the about page and the app version will say what version it is on.  

Give it a shot .it will open ( It should anyway)

Send me an e mail I will send  a short video from my phone

donaldjames1990@gmail.com

Once again sorry you are having grief- donnie

Donnie Posted at 2016-4-13 14:46
Keep in mind one fact.  YOU DO NOT UPDATE THE RC WITH 1.8.80  That is only for the Aircraft .  The  ...

Some progress here.

I did a complete factory reset of the iPad via iTunes. After the reset I was finally able to launch the DJI GO app and Connect.

However, DJI GO shows "RC signal lost" and on the "About" tab both the RC and Aircraft versions are "Unknown". I do get a video though and the craft reacts to most inputs of the RC. I was also able to relink the RC to the aircraft as well. I was also able to calibrate with no issues. Also, video is showing again.

Next step is to get rid of the RC signal lost - most likely, because I know my RC is not on the latest firmware.

I did downgrade the aircraft to 1.7.0060 (success), but same result.

I just bought the new USB port for my RC with HDMI for $100 plus shipping. Fixed my RC. I'm guessing that there is a major problem with the USB board on the RC as there are a lot of people with this problem. I cloud not be bothered sending my unit in for warranty and waiting for ever. Mine acted like the USB was dead. There was no beep when connected to any device. Samsung devices would show that they were being charged but would not connect. iPads and iPhones would not connect or beep or give any warnings. It was as if you didn't plug it in. No device would change the ap to say anything but "how to connect". Now with my new USB board with the HDMI port the RC works great. I could connect easily and upgrade the RC with the DJI Go app. The only mistake I made was to update the RC before updating the P3P. So I then had to update it with the SD card. My RC was working perfect last fall. I never used my unit over the winter and when I went to use it this spring I updated my DJI Go app and then turned on my RC and P3P and the RC would not connect. The RC would fly the P3P but would not connect to the app. I updated the P3P to the latest firmware and still nothing. I spent weeks messing around with firmware upgrades. I took a guess that the USB port was faulty on the RC and decided to just buy a new one as they were available on DJI website. Only took about a week to get it and a few minutes to install. Like I said it works great now.

aerdt Posted at 2016-4-14 04:03
Some progress here.

I did a complete factory reset of the iPad via iTunes. After the reset I was f ...

Hi I did the same, I did a restore connected to iTunes with my PC, I can now connect the iPad to the RC again, I can control the Motors, Camera etc but I still have no camera feed (which I think is a stuffed video board or something.
I can now get into the (about) screen and it tells me.
App Version 2.7.1
Aircraft Version 1.8.80
RC Version 1.6.0

the screen comes up in red with (Weak Image Transmission Signal)

Prior to this I did a full factory reset of the iPad and reinstalled the Go app and it only came up with the  (how to connect) button.

Seems like a back up then a full restore through iTunes and PC fixes that problem.

Now to get the Bitch sent off and the camera feed restored and can get to flying again.

aerdt Posted at 2016-4-13 15:03
Some progress here.

I did a complete factory reset of the iPad via iTunes. After the reset I was f ...

Ok, I would get the Aircraft back to 1.8.  and then make sure the RC is loaded at 1.6.  Keep in mind if you can control the Aircraft  and get Live video , I dont know how you are getting signal lost.  You may need to go outside with the system, away from any interference.
Also for the Versions to be visible on the Go App:  YOU MUST BE IN STANDBY MODE : THIS MEANS EVERYTHING IS ON , LIKE ABOUT TO FLY .   If you can see video and control the aircraft the version nubers will be there.  Just make sure everything is ON

Write down the numbers and please post them so I understand where you are at.




Cheers- donnie

Donnie Posted at 2016-4-14 14:18
Ok, I would get the Aircraft back to 1.8.  and then make sure the RC is loaded at 1.6.  Keep in mind ...

Hi all,

I fixed the issue.

a) By doing a complete factory reset of the iPad (to "Connect" with DJI GO)
b) By pressing the "Academy" button in the top right in DJI GO for 5-10 seconds to force a reflash of the RC firmware

In my case my RC first updated to 1.5.8 (after 3 tries), then after connecting with my aircraft DJI GO suggested to upgrade the RC to 1.6 and finally I reflashed the craft to 1.8.80

All is well. Thanks all for the help. I hope this will help others as well.
To re-iterate my issue: After upgrading the drone to 1.8.80, my DJI Go would not connect with anymore and just showed the "How to connect" button. It almost appeared that the USB on the RC was faulty, but I knew that it wasn't. After the factory restore (important: with iTunes, a full factory restore) to iOS v9.3.1, it was able to "Connect" again in DJI Go, but all my version numbers in the "About" menu showed "Version unknown" and that status showed "RC signal lost".

DJI-Ken Posted at 2016-4-12 14:38
You are on the latest update. Go to the settings and scroll down to developer options and make sur ...

Thanks Ken, I will try this.